Manuals / Frymaster / Kitchen Appliance / Fryer

Frymaster H52 Series warranty How to Activate or Deactivate the Frypot BOIL-OUT Feature

Models: H52 Series

1 48

Download 48 pages 48.78 Kb

Page 23

How to Activate or Deactivate the Frypot BOIL-OUT Feature

For the right side of a split-vat or for a full-vat:Press the right 1 switch to go UP a degree (maximum of 5 for Fahrenheit or 3 for Celsius). Press the right 2 switch to go DOWN a degree (maximum of 5 for Fahrenheit or 3 for Celsius).

5.Press the switch to save the settings.

6.Press either ON/OFF switch to exit the setup mode. Both displays will change to OFF.

How to Activate or Deactivate the Frypot BOIL-OUT Feature

1.Enter the setup mode. See How to Enter the Setup Mode on Page 3-8.

2.Press and release the switch until BOIL-OUTappears in the display.

3.Press the right 1 or 2 switch to toggle the boil-out mode ON or OFF.

4.Press the switch to save the settings.

5.Press either ON/OFF switch to exit the setup mode. Both displays will change to OFF.

3.6.2 M-100B™ Computer Programming Mode

How to Enter the Program Mode

1.Press the ON/OFF switches until both displays of cooking computer indicate OFF. Press the left product selection switch and the left 1 and 2 cook switches simultaneously. Release all three switches at the same time.

2.When the program mode has been entered, the display will flash M-100B computer briefly, followed by the software version number. After a few seconds, Fr fries yes or Fr fries no will be displayed, depending upon previous program settings.

How to Reset the Computer to the Factory Defaults

While in the program mode, press all 4 cook switches (left and right 1 and 2 ) simultaneously to reset the computer to the factory defaults. See How to Enter the Program Mode above. Updating menu will flash in the display, followed by epra cleared and cooks cleared. After a few seconds, Fr fries yes will be displayed, indicating that the computer has been reset to the factory defaults.

How to Change the Shake, Pull, Or Quality Times for Menu Items

1.Enter the program mode. (See How to Enter the Program Mode above.)

2.Press and release the switch until the product to be changed appears in the left display.

3–10

Image 23

Frymaster H52 Series How to Activate or Deactivate the Frypot BOIL-OUT Feature, 3.6.2 M-100B Computer Programming Mode

Contents

SERVICE HOTLINE OPERATOR’S MANUAL FRYMASTER H52 SERIES GAS FRYERTABLE OF CONTENTS FOR YOUR SAFETYPage Example of a WARNING box CHAPTER 1 INTRODUCTION1.1 General Example of a CAUTION boxCE Standard Example of box used to distinguish CE and Non-CE specific information 1.5 Shipping Damage Claim Procedure1.3 Computer Information 1.4 European Community CE Specific InformationRETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE 1.6 Service InformationDANGER CHAPTER 2 INSTALLATION INSTRUCTIONS2.1 General Installation Requirements CLEARANCE AND VENTILATIONELECTRICAL GROUNDING REQUIREMENTS This equipment requires electrical power for operationDo not attempt to use the equipment during a power outage NATIONAL CODE REQUIREMENTSin this section 2.2 Caster/Leg Installation2.3 Pre-Connection Preparations DANGER Do not connect fryer to gas supply before completing each stepNon-CE Standard for Incoming Gas Pressures CE Standard for Incoming Gas Pressuresfor Fryers Manufactured After April for Fryers Manufactured Through AprilH152-2 units are not approved for G30 Butane gas 2.4 Connection to Gas LineRequired airflow for the combustion air supply is 2m3/h per kW service agency for serviceCE Standard If gas odors are detected, shut off the gas supply to the fryerDANGER 2.5 Converting to Another Gas Type4. It is suggested that the burner manifold pressure be checked at this time by the local gas com- pany or an authorized service agent. Refer to “Check Burner Manifold Pressure” in Chapter 5 of this manual for the proper procedure. The accompanying tables list the burner manifold gas pressures for the various gas types that can be used with this equipment 2.6 Frypot Boil-Out Non-CE Gas Conversion KitsCE Gas Conversion Kits for Units with Gas Valve CE GAS CONVERSION INSTRUCTIONS3.2 Finding Information 3.1 Equipment Setup and Shutdown Procedures SetupCHAPTER 3 OPERATING FRYERS WITH M100B COOKING COMPUTERS ShutdownDESCRIPTION 3.3 Introduction To The M-100B Cooking ComputerOperating the Computer on Full-Vat Fryers 3.4 M-100B Computer Operating Instructionsproperly filled with vegetable oil. See Section Cooking Product Full-Vat or Split-Vat Viewing the Frypot Temperature Actual or SetpointOperating the Computer on Split-Vat Fryers Recovery Out of Range REC LOCK 3.5 M-100B Computer Problem Condition IndicatorsOpen Drain Valve Indication Low Temperature IndicationIn the Program Mode, the operator can In the Setup Mode, the operator canProbe Failure Indication 3.6 M-100B Computer Set-Up and Programming InstructionsHow to Configure the Computer for Use on a Gas Fryer 3.6.1 M-100B Computer Setup ModeHow to Enter the Setup Mode How to Change the Computer’s Display LanguageHow to Calibrate Computer Temperature to Actual Frypot Temperature How to Change Computer Product/Temperature DisplaysHow to Change the Shake, Pull, Or Quality Times for Menu Items How to Activate or Deactivate the Frypot BOIL-OUT FeatureHow to Enter the Program Mode How to Reset the Computer to the Factory DefaultsHow to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test Menu How to Suppress a Shake, QA, or Duty Function How to Display the Product Cycle Accumulator Information How to Turn the Display of a Factory-Programmed Menu Item On and OffHow to Display “Use Time” Information How to Use the Filter Countdown Timer 4.2 Introduction to the Analog Controller 4.1 Equipment Setup and Shutdown Procedures Setupswitch to the ON position. Failure to do so could damage the frypot CHAPTER 4 OPERATING FRYERS WITH ANALOG CONTROLLERSA B C D E F G H I J K L M N DESCRIPTIONproperly filled with vegetable oil. See Section control-check procedure4.3 Analog Controller Operating Instructions 4.4 Analog Controller High-Limit Checkrelease switch container for disposal Always wear appropriate protective gloves when draining or filteringCHAPTER 5 FILTERING 5.1 Draining and Manual Filtering DANGERDANGER 5.2 Operating the Built-In Filtration SystemPREPARING THE FILTER UNIT FOR USE and CHANGING THE FILTER PAPER 1. Turn the controller OFFNOTE! DO NOT use filter powder if using the optional filter pad If using the optional filter pad, place the ring over the padHot oil will rush out, creating an extreme hazard to cooking temperaturetemperature probe or operating thermostat OPERATING THE FILTER UNITPage 5.3 Getting the Most Out of Your Filter g. Insert filter pan into the filter base assembly Verify that electrical cords are securely plugged in CHAPTER 6 PREVENTIVE MAINTENANCE AND TROUBLESHOOTING6.1 Preventive Maintenance 6.2 TroubleshootingREC LOCK 6.2.1 Troubleshooting Fryers with M100B Computerscomputer on another If problem repeatsIGNITION FAILURE IGNITION FAILUREwill not enter programming operating6.2.3 Troubleshooting Fryers Equipped with Analog Controllers BURNERS DO NOT LIGHT POWER LIGHT ON HEAT LIGHT ON TROUBLE LIGHT ON 6.2.4 Troubleshooting Built-in Filtration System stopped? thermal overload resetpump microswitch, a failed pump relay for a while and then