XTE Alarm, Border Alarm, Border alarm, XTE alarm

6.2 XTE Alarm, Border Alarm

XTE alarm

The XTE (cross-track error) alarm alerts you when your ship strays from its intended course. You may preset the alarm limit from 0.01 nautical miles to a maximum lane width of 99.99 nautical miles. The alarm will be released when your ship goes out of the lane limits.

Destination

Audible alarm sounds.

XTE

Starting point

Figure 6-5 How the XTE alarm works

1.Press the [ALARM] key to display the ALARM menu.

2.Select XTE from the XTE/BORDER field.

3.Press [↓] to select ALARM RANGE.

4.Enter alarm range. To enter 0.02 nautical miles, for example, press [0], [2], [0] and [0].

5.Press the [ENT] key.

Border alarm

The border alarm defines an area, consisting of two waypoints, which you do not want to cross. The alarm will sound when your ship crosses the area defined by the two waypoints.

Width of border line
(Alarm width)	Border
Starting point	Destination
	Alarm range

Alarm sounds.

Figure 6-6 How the border alarm works

6-3

Page 71

Image 71

Furuno GD-3300, GP-3300 manual XTE Alarm, Border Alarm, Border alarm, XTE alarm

Contents

Page 00080834300 Safety Instructions Furuno agent or dealer About the TFT LCD Table of Contents Video Pilot Display Navigation Data Display External Event Mark Target Mark Lines 11.9 Memory Capacity Chart Symbols, Contour Lines Attributes12.1 Preventive Maintenance 12-1 12.2 Time Differences Geodetic Chart List Word to Furuno GD-3300/GP-3300 Owners Foreword Vii Features Viii Menu Tree GPS Antenna Unit GPA-017S System Configuration Control Description Operational Overview Control description Inserting Chart Cards Turning the power on Turning the Power On/Off Turning the cursor on/off TrackballCursor +36 44.257’ N Shifting the DisplayReturning Own Ship Marker to Screen Center Cursor information Selecting Screen Center by Cursor Position How to select screen center Display Brilliance and Key Backlighting Chart Scale Card drives Card Drives, Chart CardsDisplaying an electronic chart with the power turned on Insert chart card label side up in the lower slot Press the eject button Ejecting the chart cardChart card troubleshooting Care and handling of the cards Table below shows Furuno chart symbols and their meanings Chart iconsFuruno chart symbols Buoy, lighthouse data display on Navionics charts Comparison of FURUNO, Navionics chart cards Data Window Data shown when cursor is on Nav data mode description Data shown when cursor is offPlot mode description Video pilot mode description Menu operation versus key operation Menu Operation Main menu description Main menu description Summary of menu operation Operation on the DisplaySelecting options Entering data Operational Status Icons Economy Mode +36 44.257’ N 140.50 35.92NM 134 40.719’ E Plot Mode DisplaysPlot display when cursor is on 36 44.257’ N Plot display when cursor is off 22 Initial Settings menu Setting the Time and Date 340.5 TrackStopping Track Recording Press MENU, 9 and 1 to display the EDIT/TRACK Mark menu Track ColorChanging Color, Appearance of Specific Track EDIT/TRACK Mark menu Press MENU, 9, 1 to display the EDIT/TRACK menu Deleting TrackDeleting track by color Deleting specific track with cursor, box cursor Delete Track display Deleting all track Plot interval by time or distance Track Plotting IntervalHow the track is drawn Plot interval and track reconstruction Setting plot interval 2 to time Setting plot interval 1 by time Customizing the Hold Function Turning off track display when track is not being recordedConnecting track after restarting track recording Customizing the Plot Intvl Key Setup for manually entering plot intervalTuning off a plot interval Page Entering marks at own ship’s position MARKS, LinesEntering Marks Entering marks with the cursor Press the Mark Color key to show the Change Mark Color menu Changing Current Mark Color Changing Shape, Color of Specific Marks Deleting marks with the cursor Deleting MarksDeleting specific marks Deleting all marks Erasing an external event mark External Event MarkTarget Mark Lines Deleting lines Entering a lineChanging line color Waypoints Waypoints Place the data input cursor on waypoint Entering WaypointsWaypoint entry by L/L coordinates Waypoint entry by cursor Waypoint entry by range and bearing Waypoint entry at own ship’s position Waypoint entry by navigation aid Entering a Comment for a Waypoint Turning Specific Waypoint Displays On/Off Deleting waypoints by cursor Deleting Waypoints Deleting external waypoint Setting destination waypoint by cursorDestination Waypoint Deleting waypoints through waypoint list Setting destination waypoint by range and bearing Setting destination waypoint by waypoint number 11 How a destination waypoint is shown on the display When you set a destination waypoint Press the Plot key to display the Data Display Displaying range and bearing to destination waypoint36 34.000’ N 134 20.524’ E Select Cancel from the Dest field Press the ENT key Cancelling Destination WaypointCancelling destination waypoint through the menu Cancelling destination waypoint by key input Sample route Route Navigation Creating routes through the route list Creating Routes Press the Route key to display the Route NO. menu Creating routes with waypoint numbers Menu keyCreating routes with waypoint numbers Route key Press the Route to display the Route NO. menu Creating routes with the cursorSelect WPT no Enter waypoint numbers Press the ENT key About route navigation Following a Route Temporarily Deselecting a Route Waypoint Example of when to deselect waypoints Deleting specific route waypoints Deleting Route Waypoints Deleting all route waypoints Cancelling Route Navigation 10 Route list Route Calculation Arrival alarm AlarmsArrival Alarm, Anchor Watch Alarm Alarm range of arrival alarm Anchor watch alarm XTE alarm XTE Alarm, Border AlarmBorder alarm Press ← twice Ship’s Speed Alarm Silencing the alarm buzzer When the Alarm Buzzer SoundsWhat alarm is sounding? Video Pilot Display FeaturesCompares the features of the video pilot and plot displays Mark data Destination data 135 21.288’ E Comparison of plot and video pilot displays34 44.463’ 34 44.463’ N Navigation Data Display 44 N 135 21 E Autopilot Data Features Available with Autopilot Connection Sample autopilot information on plot display Autopilot Information on Plot Display 134 40.719’ E 10.0KTS Autopilot Information on Video Pilot Display Autopilot in Auto mode Autopilot in Manual mode Autopilot on, destination waypoint selected Autopilot in NAV mode Press the 3 key to select Save Data to Memory Card Memory Card OperationsFormatting Memory Cards Saving Data to Memory Cards Save Track display File name example Playing Back Memory Cards Press the 5 key to select Display Memory Card Saving, Playing Back Initial SettingsSaving initial settings Playing back initial settings Adding track, marks/lines Editing Memory CardsDeleting track, marks/lines from a memory card Deleting files 10-1 GPS Receiver Operation GP-3300GPS Information on the Navigation Data Display GPS receiver status 10-2 Satellite scheduleFrequency deviation 10-3 GPS and Dgps Initial SettingsSatellite data 10-4 GPS initial settings menu descriptionDescribes the GPS Initial Settings menu Press Menu and 8, and then press − to set the cursor on Satellite Force Health/Deselection10-5 10-6 GPS SmoothingSpeed and course GPS smoothing Latitude and longitude GPS smoothing 10-7 Setting GPS smoothing 10-8 Cold Start 10-9 Selecting chart systemGeodetic Datum Correcting GPS Position 11-1 Other FunctionsDisplaying Position in Loran TDs Displaying position in Loran a TDs 11-2 Bearing Display ReferenceDisplaying position in Loran C TDs 11-3 Magnetic DeviationDisplaying true bearing 11-4 Changing Chart Appearance 11-5 Correcting Chart PositionCorrecting chart position by cursor 11-6 Correcting chart position by latitude and longitudeCorrections chart position by Δ Delta L/L 11-7 Cancelling chart position correctionLoran TD Correction 11-8 Calculating R/B Between Two PointsCalculating R/B by latitude and longitude 11-9 Calculating R/B by waypoint numbers Memory Capacity Locking Preferred SettingsLocking or unlocking preferred settings Default memory arrangement is as shown in Figure 11-11 When the track memory becomes full oldest track is deletedTrack memory 11-12 When the mark memory becomes full no marks can be enteredApportioning the Memory Mark/line memory 11-13 Reading Number of Track, Marks Used 11-14 Smoothing 11-15 Selecting Navaid 11-16 Track, Mark and Marker Attributes 11-17 Initial settings menuSpecial menu 11-18 Customizable items on the Initial Settings menu Select item and option as appropriate Press the ENT key Chart Symbols, Contour Lines Attributes11-19 12-1 Maintenance & TroubleshootingPreventive Maintenance 12-2 Diagnostic TestsSelf test at power on Memory circuits, I/O ports To escape from the test, press any key Keyboard test12-3 Check the pattern for color dropout Press any key to escape Test pattern 1 color dropoutTest pattern 2 color distortion 12-4 12-5 Error Messages No files on memory card to delete 12-6Memory card replaced during operation No file by that name exists Waypoint being used as destination waypoint Replacement of Fuse12-7 12-8 Replacement of BatteriesMemory card battery 12-9 Verifying Program Version NoPlotter section GPS section GP-3300 12-10 Troubleshooting Table 12-11 12-12 Clearing Memories Press the 8 key to select Clear Memory 12-13 Time Differences Appendix Adindan Geodetic Chart List GD/GP-3300 Specifications of Color Video PLOTTER/COLOR GPS Plotter Coating Color Index-1 Index Index-2 Index-3