Replacement of Batteries, Memory card battery

12.5 Replacement of Batteries

Both the GDC Board inside the display unit and the memory cards use a battery to store information. The life of these batteries is about three years. When the voltage of a battery is low, the “battery” icon appears on the display. The offending battery should be replaced at your earliest convenience, so that important information will not be lost.

Table 12-1 Replacement battery types and code numbers

Battery	Type	FURUNO Code No.

Memory	Lithium Battery,	000-141-093
Card Battery	CR2025
Battery on	Lithium Battery,	000-123-713
GDC Board	BR-213AE 2P

Memory card battery

Insert new battery within 10 minutes after removing expired battery.

Otherwise, the information stored on the card will be lost.

1.Slide tab on card leftward. Remove battery.

2.Insert new battery plus terminal facing upward.

3.Close battery lid.

Tab

Face "+" mark upward.

Battery case

Figure 12-6 How to replace memory card battery

12-8

Page 124

Image 124

Furuno GP-3300, GD-3300 manual Replacement of Batteries, Memory card battery, 12-8

Contents

Page 00080834300 Safety Instructions About the TFT LCD Furuno agent or dealer Table of Contents External Event Mark Target Mark Lines Video Pilot Display Navigation Data Display Chart Symbols, Contour Lines Attributes 12.1 Preventive Maintenance 12-1 12.2Time Differences Geodetic Chart List 11.9 Memory Capacity Foreword Word to Furuno GD-3300/GP-3300 Owners Features Vii Menu Tree Viii System Configuration GPS Antenna Unit GPA-017S Operational Overview Control Description Inserting Chart Cards Control description Turning the Power On/Off Turning the power on Cursor TrackballTurning the cursor on/off Shifting the Display Returning Own Ship Marker to Screen CenterCursor information +36 44.257’ N How to select screen center Selecting Screen Center by Cursor Position Chart Scale Display Brilliance and Key Backlighting Card Drives, Chart Cards Displaying an electronic chart with the power turned onInsert chart card label side up in the lower slot Card drives Ejecting the chart card Chart card troubleshootingCare and handling of the cards Press the eject button Furuno chart symbols Chart iconsTable below shows Furuno chart symbols and their meanings Comparison of FURUNO, Navionics chart cards Buoy, lighthouse data display on Navionics charts Data shown when cursor is on Data Window Data shown when cursor is off Plot mode descriptionVideo pilot mode description Nav data mode description Menu Operation Menu operation versus key operation Main menu description Main menu description Operation on the Display Selecting optionsEntering data Summary of menu operation Economy Mode Operational Status Icons Plot display when cursor is on Plot Mode Displays+36 44.257’ N 140.50 35.92NM 134 40.719’ E Plot display when cursor is off 36 44.257’ N Setting the Time and Date 22 Initial Settings menu Stopping Track Recording Track340.5 Changing Color, Appearance of Specific Track Track ColorPress MENU, 9 and 1 to display the EDIT/TRACK Mark menu EDIT/TRACK Mark menu Deleting Track Deleting track by colorDeleting specific track with cursor, box cursor Press MENU, 9, 1 to display the EDIT/TRACK menu Deleting all track Delete Track display Track Plotting Interval How the track is drawnPlot interval and track reconstruction Plot interval by time or distance Setting plot interval 1 by time Setting plot interval 2 to time Connecting track after restarting track recording Turning off track display when track is not being recordedCustomizing the Hold Function Tuning off a plot interval Setup for manually entering plot intervalCustomizing the Plot Intvl Key Page MARKS, Lines Entering MarksEntering marks with the cursor Entering marks at own ship’s position Changing Current Mark Color Press the Mark Color key to show the Change Mark Color menu Changing Shape, Color of Specific Marks Deleting Marks Deleting specific marksDeleting all marks Deleting marks with the cursor External Event Mark Target MarkLines Erasing an external event mark Changing line color Entering a lineDeleting lines Waypoints Waypoints Waypoint entry by L/L coordinates Entering WaypointsPlace the data input cursor on waypoint Waypoint entry by cursor Waypoint entry at own ship’s position Waypoint entry by range and bearing Entering a Comment for a Waypoint Waypoint entry by navigation aid Turning Specific Waypoint Displays On/Off Deleting Waypoints Deleting waypoints by cursor Setting destination waypoint by cursor Destination WaypointDeleting waypoints through waypoint list Deleting external waypoint Setting destination waypoint by waypoint number Setting destination waypoint by range and bearing When you set a destination waypoint 11 How a destination waypoint is shown on the display Displaying range and bearing to destination waypoint 36 34.000’ N134 20.524’ E Press the Plot key to display the Data Display Cancelling Destination Waypoint Cancelling destination waypoint through the menuCancelling destination waypoint by key input Select Cancel from the Dest field Press the ENT key Route Navigation Sample route Creating Routes Creating routes through the route list Creating routes with waypoint numbers Route key Creating routes with waypoint numbers Menu keyPress the Route key to display the Route NO. menu Select WPT no Enter waypoint numbers Press the ENT key Creating routes with the cursorPress the Route to display the Route NO. menu Following a Route About route navigation Example of when to deselect waypoints Temporarily Deselecting a Route Waypoint Deleting Route Waypoints Deleting specific route waypoints Cancelling Route Navigation Deleting all route waypoints Route Calculation 10 Route list Arrival Alarm, Anchor Watch Alarm AlarmsArrival alarm Anchor watch alarm Alarm range of arrival alarm Border alarm XTE Alarm, Border AlarmXTE alarm Ship’s Speed Alarm Press ← twice What alarm is sounding? When the Alarm Buzzer SoundsSilencing the alarm buzzer Compares the features of the video pilot and plot displays FeaturesVideo Pilot Display Destination data Mark data Comparison of plot and video pilot displays 34 44.463’34 44.463’ N 135 21.288’ E 44 N 135 21 E Navigation Data Display Features Available with Autopilot Connection Autopilot Data Autopilot Information on Plot Display Sample autopilot information on plot display Autopilot Information on Video Pilot Display 134 40.719’ E 10.0KTS Autopilot in Manual mode Autopilot in Auto mode Autopilot in NAV mode Autopilot on, destination waypoint selected Formatting Memory Cards Memory Card OperationsPress the 3 key to select Save Data to Memory Card Saving Data to Memory Cards Save Track display Playing Back Memory Cards File name example Saving, Playing Back Initial Settings Saving initial settingsPlaying back initial settings Press the 5 key to select Display Memory Card Editing Memory Cards Deleting track, marks/lines from a memory cardDeleting files Adding track, marks/lines GPS Receiver Operation GP-3300 GPS Information on the Navigation Data DisplayGPS receiver status 10-1 Frequency deviation Satellite schedule10-2 Satellite data GPS and Dgps Initial Settings10-3 Describes the GPS Initial Settings menu GPS initial settings menu description10-4 10-5 Satellite Force Health/DeselectionPress Menu and 8, and then press − to set the cursor on GPS Smoothing Speed and course GPS smoothingLatitude and longitude GPS smoothing 10-6 Setting GPS smoothing 10-7 Cold Start 10-8 Selecting chart system Geodetic DatumCorrecting GPS Position 10-9 Other Functions Displaying Position in Loran TDsDisplaying position in Loran a TDs 11-1 Displaying position in Loran C TDs Bearing Display Reference11-2 Displaying true bearing Magnetic Deviation11-3 Changing Chart Appearance 11-4 Correcting chart position by cursor Correcting Chart Position11-5 Corrections chart position by Δ Delta L/L Correcting chart position by latitude and longitude11-6 Loran TD Correction Cancelling chart position correction11-7 Calculating R/B by latitude and longitude Calculating R/B Between Two Points11-8 Calculating R/B by waypoint numbers 11-9 Locking Preferred Settings Locking or unlocking preferred settingsDefault memory arrangement is as shown in Figure Memory Capacity Track memory When the track memory becomes full oldest track is deleted11-11 When the mark memory becomes full no marks can be entered Apportioning the MemoryMark/line memory 11-12 Reading Number of Track, Marks Used 11-13 Smoothing 11-14 Selecting Navaid 11-15 Track, Mark and Marker Attributes 11-16 Special menu Initial settings menu11-17 Customizable items on the Initial Settings menu 11-18 11-19 Chart Symbols, Contour Lines AttributesSelect item and option as appropriate Press the ENT key Preventive Maintenance Maintenance & Troubleshooting12-1 Diagnostic Tests Self test at power onMemory circuits, I/O ports 12-2 12-3 Keyboard testTo escape from the test, press any key Test pattern 1 color dropout Test pattern 2 color distortion12-4 Check the pattern for color dropout Press any key to escape Error Messages 12-5 12-6 Memory card replaced during operationNo file by that name exists No files on memory card to delete 12-7 Replacement of FuseWaypoint being used as destination waypoint Memory card battery Replacement of Batteries12-8 Verifying Program Version No Plotter sectionGPS section GP-3300 12-9 Troubleshooting Table 12-10 12-11 Clearing Memories 12-12 12-13 Press the 8 key to select Clear Memory Appendix Time Differences Geodetic Chart List Adindan Specifications of Color Video PLOTTER/COLOR GPS Plotter GD/GP-3300 Coating Color Index Index-1 Index-2 Index-3

12.5 Replacement of Batteries

Table 12-1 Replacement battery types and code numbers

Battery

Type

FURUNO Code No.

Memory card battery

Figure 12-6 How to replace memory card battery

12-8