Furuno GD-3300, GP-3300 1.14 Menu Operation

1-14

1.14 Menu Operation

Menu operation versus key operation

Many functions of your plotter can be executed through the menu or

by pressing the key associated with function desired. For example,

you can enter a waypoint by pressing the [WPT] key, or [MENU] and

[1].

To display the menu, press the [MENU] key to display the Main menu.

To select a menu, press appropriate numeric key.

1 WAYPOINT

2 ROUTE

3 SAVE DATA TO MEMORY CARD

4 LOAD MEMORY CARD

5 DISPLAY MEMORY CARD

6 CORRECT POSITION

7 APPORTION/DELETE MEMORY

8 INITIAL SETTINGS

9 MISC

SELECT BY USING NUMBER KEY.

Figure 1-18 Main menu

Contents

Main *00080834300**00080834300* *OME43920F00**OME43920F00* *OME43920F00**OME43920F00* iiiiiiiiiiiii i SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD WARNING ii CAUTION iii TABLE OF CONTENTS FOREWORD MENU TREE SYSTEM CONFIGURATION OPERATIONAL OVERVIEW TRACK MARKS, LINES iv WAYPOINTS ROUTE NAVIGATION ALARMS VIDEO PILOT DISPLAY, NAVIGATION DATA DISPLAY AUTOPILOT DATA GPS RECEIVER OPERATION (GP-3300) OTHER FUNCTIONS MAINTENANCE & TROUBLESHOOTING APPENDIX SPECIFICATIONS INDEX Declaration of Conformity FOREWORD A Word to FURUNO GD-3300/GP-3300 Owners vii Features viii MENU TREE MENU 1 WAYPOINT 2 ROUTE 3 SAVE DATA TO MEMORY CARD 4 LOAD MEMORY CARD 5 DISPLAY MEMORY CARD 6 CORRECT POSITION 7 APPORTION/DELETE MEMORY 8 INITIAL SETTINGS (See below.) 9 MISC SYSTEM CONFIGURATION 1-1 OPERATIONAL OVER VIEW Figure 1-1 Display unit OUT Trackball 4 1.2 Inserting Chart Cards Normally, insert appropriate chart card before turning on the power. 1. Open the card drive cover. 1-3 1.3 Turning the Power On/Off Turning the power on 1-4 1.4 The Trackball 1.5 The Cursor Turning the cursor on/off 1-5 Cursor information 1.6 Shifting the Display 1.7 Returning Own Ship Marker to Screen Center 1-6 1.8 Selecting Screen Center by Cursor Position 1-7 1.9 Chart Scale 34 44.258 N 340.5123.4NM 134 40.719 E 341.2 123.4NM 1.10 Display Brilliance and Key Backlighting 1-8 1.11 Card Drives, Chart Cards Card drives Displaying an electronic chart with the power turned on Page 1-10 Chart icons FURUNO chart symbols The table below shows FURUNO chart symbols and their meanings. Table 1-3 FURUNO chart symbols 1-11 Comparison of FURUNO, NAVIONICS chart cards Buoy, lighthouse data display on NAVIONICS charts 1-12 FL (2) 12S 15M 1.12 The Data Window Data shown when cursor is on 1-13 Data shown when cursor is off 1.13 Display Modes Plot mode description Video pilot mode description Nav data mode description 1-14 1.14 Menu Operation Menu operation versus key operation Page 1-16 1.15 Operation on the Display Selecting items Selecting options Entering data Summary of menu operation H LL 1.17 Economy Mode 1-18 1.18 Plot Mode Displays +36 44.257 N 50.5 134 40.719 E 10.0KTS +36 44.257 N 140.5035.92NM 134 40.719 E 50.5 1-19 Plot display when cursor is off Figure 1-21 Plot display, cursor off 36 44.257 N 50.5 134 40.719 E 10.0KTS 36 44.257 N 59.835.92NM 134 40.719 E 50.5 1-20 1.19 Setting the Time and Date 2-1 TRACK 2.1 Stopping Track Recording +36 44.257 N 340.5 134 40.719 E 10.0KTS 2-2 2.2 Track Color 2.3 Changing Color, Appearance of Specific Track 2-3 2-4 2.4 Deleting Track Deleting track by color Deleting specific track with cursor, box cursor 2-5 Deleting all track 2-6 2.5 Track Plotting Interval How the track is drawn Plot interval and track reconstruction Plot interval by time or distance 2-7 Setting plot interval 1 by time Setting plot interval 2 to time 2-8 2.6 Customizing the Hold Function Turning off track display when track is not being recorded Connecting track after restarting track recording 2-9 2.7 Customizing the PLOT INTVL Key Setup for manually entering plot interval Tuning off a plot interval Page 3-1 MARKS, LINES 3.1 Entering Marks Entering marks with the cursor Entering marks at own ships position Entering marks by manual input of latitude and longitude 3.2 Changing Current Mark Color 3-3 3.3 Changing Shape, Color of Specific Marks 3-4 3.4 Deleting Marks Deleting marks with the cursor Deleting specific marks Deleting all marks 3-5 3.5 External Event Mark Erasing an external event mark Turning on/off event mark display 3.6 Target Mark 3.7 Lines 3-6 Entering a line Changing line color Deleting lines 4-1 WAYPOINTS 4-2 4.1 Entering Waypoints Waypoint entry by L/L coordinates Figure 4-2 Waypoint list 3. Place the data input cursor on waypoint 6. 4-3 4-4 Waypoint entry at own ships position Waypoint entry by range and bearing 4-5 Waypoint entry by navigation aid 4.2 Entering a Comment for a Waypoint 4-6 4.3 Turning Specific Waypoint Displays On/Off Turning on/off specific waypoints displays through the REGISTER WAYPOINT menu 4-7 Turning on/off specific waypoints displays through the waypoint list 1. Press the [MENU] key to display the menu. 2. Press the [1] key to display the WAYPOINT list. 4.4 Deleting Waypoints You can delete unnecessary waypoints by the cursor or through the waypoint list. Deleting waypoints by cursor 1. Place the cursor on the waypoint you want to delete. 2. Press the [CLR] key. 4-8 4.5 Destination Waypoint Setting destination waypoint by cursor 4-9 Setting destination waypoint by waypoint number Setting destination waypoint by range and bearing 4-10 When you set a destination waypoint... 4-11 Displaying range and bearing to destination waypoint Figure 4-12 Location of destination waypoint information 36 34.000 N 340.5 134 20.524 E 10.0KTS 36 34.000 N 176.5 14.5NM 134 20.524 E 340.5 4.6 Cancelling Destination Waypoint 5-1 ROUTE NAVIGATION 5-2 5.1 Creating Routes Creating routes through the route list 5-3 Creating routes with waypoint numbers: MENU key Creating routes with waypoint numbers: ROUTE key 5-4 Creating routes with the cursor 5-5 5.2 Following a Route About route navigation 5-6 5.3 Temporarily Deselecting a Route Waypoint 5-7 5.4 Deleting Route Waypoints Deleting specific route waypoints 5-8 Deleting all route waypoints 5.5 Cancelling Route Navigation 5-9 5.6 Route Calculation 6-1 ALARMS 6.1 Arrival Alarm, Anchor Watch Alarm Arrival alarm 6-2 Anchor watch alarm 6-3 6.2 XTE Alarm, Border Alarm XTE alarm Border alarm 6-4 6.3 Ships Speed Alarm 6-5 6.4 When the Alarm Buzzer Sounds... Silencing the alarm buzzer What alarm is sounding? 7-1 VIDEO PILOT DISPLAY, NAVIGATION DATA DISPLAY 7.1 Video Pilot Display Features 34 44.465 N 355.6 95.59NM 135 21.289 E 1.1KTS 7-2 Destination data Mark data 7-3 Comparison of plot and video pilot displays 34 44.463 N 314.5 135 21.288 E 0.4KTS 34 44.463 N 314.5 135 21.288 E 0.4KTS 7-4 7.2 Navigation Data Display Figure 7-4 Sample navigation data display 3444. 454 N 13521. 288 E 8-1 AUTOPILOT DATA 8.1 Features Available with Autopilot Connection 8-2 8.2 Autopilot Information on Plot Display Figure 8-2 Sample autopilot information on plot display 36 44.257 N 340.5 Autopilot information (Autopilot FAP-330 in NAV Mode) 358.0 (FAP-330 in AUTO mode) (FAP-330 in MANUAL mode) 8-3 36 44.257 N 340.5 8-4 Autopilot on, no destination waypoint selected Figure 8-5 Course error and cross-track error indications MAN 357.0 8-5 Autopilot on, destination waypoint selected 10.1 18 (c) Autopilot in NAV mode MEMORY CARD OPERATIONS 9.1 Formatting Memory Cards 9-2 9.2 Saving Data to Memory Cards 9-3 9-4 9.3 Playing Back Memory Cards 9-5 9.4 Saving, Playing Back Initial Settings Saving initial settings Playing back initial settings 9-6 9.5 Editing Memory Cards Adding track, marks/lines Deleting track, marks/lines from a memory card Deleting files 10-1 3444. 454 N 13521. 288 E Figure 10-1 Sample navigation data display GPS receiver status Table 10-1 explains the meanings of GPS receiver status indications on the navigation data display. 10-2 Satellite schedule Frequency deviation 10-3 Satellite data 10.2 GPS and DGPS Initial Settings 10-4 GPS initial settings menu description 10-5 10.3 Satellite Force Health/Deselection 10-6 10.4 GPS Smoothing Latitude and longitude GPS smoothing Speed and course GPS smoothing 10-7 Setting GPS smoothing 10-8 10.5 Cold Start 10-9 10.6 Geodetic Datum Selecting chart system 10.7 Correcting GPS Position OTHER FUNCTIONS 11-2 Displaying position in Loran C TDs 11.2 Bearing Display Reference 11-3 Displaying true bearing +36 44.257 N 340.5M 11.3 Magnetic Deviation 11-4 11.4 Changing Chart Appearance 11-5 11.5 Correcting Chart Position Correcting chart position by cursor 11-6 Correcting chart position by latitude and longitude Corrections chart position by (Delta) L/L 11-7 Cancelling chart position correction 11.6 Loran TD Correction 11-8 11.7 Calculating R/B Between Two Points Calculating R/B by latitude and longitude 11-9 Calculating R/B by latitude and longitude Calculating R/B by waypoint numbers 11-10 11.8 Locking Preferred Settings Locking or unlocking preferred settings 11.9 Memory Capacity 11-11 Track memory 11-12 Mark/line memory 11.10 Apportioning the Memory 11-13 11.11 Reading Number of Track, Marks Used 11-14 11.12 Smoothing 11-15 11.13 Selecting Navaid 11-16 11.14 Track, Mark and Marker Attributes Figure 11-24 Items whose attributes you can change on the INITIAL SETTINGS and SPECIAL menus 11-17 Initial settings menu Figure 11-26 SPECIAL menu Figure 11-25 INITIAL SETTINGS menu Special menu 11-18 11-19 11.15 Chart Symbols, Contour Lines Attributes 12-1 MAINTENANCE & TROUBLESHOOTING WARNING WARNING 12.1 Preventive Maintenance 12-2 12.2 Diagnostic Tests Self test at power on Memory circuits, I/O ports 12-3 Keyboard test 12-4 Test pattern 1 (color dropout) GP-3300 Test pattern 2 (color distortion) 12-5 12.3 Error Messages 12-6 12-7 12.4 Replacement of Fuse CAUTION 12-8 12.5 Replacement of Batteries Memory card battery 12-9 12.6 Verifying Program Version No. Plotter section GPS section (GP-3300) 12-10 12.7 Troubleshooting Table 12-11 (Continued on next page) 12-12 12.8 Clearing Memories 12-13 Page A-2 Geodetic Chart List SPECIFICATIONS OF COLOR VIDEO PLOTTER/COLOR GPS PLOTTER GD/GP-3300 Page Index-1 A B C INDEX D E F G Index-2 O P R S Index-3 V W X Z