Turning Specific Waypoint Displays On/Off

4.Press the [ENT] key. (If you enter a wrong character, set the data input cursor on wrong character and then enter correct character.)

5.Repeat steps 2 and 3 to complete comment.

6.Press [→] to set the cursor out of the comments column and then press the [ENT] key.

4.3Turning Specific Waypoint Displays On/Off

Turning on/off specific waypoints displays through the REGISTER WAYPOINT menu

1.Press the [WPT] key to display the REGISTER WAYPOINT menu.

MODE = CURSOR L/L OS POS. R/B LIST

WPT NO. = −

ENTER WAYPOINT NO., AND DESIGNATE WAYPOINT

POSITION BY USING CURSOR.

Figure 4-7 REGISTER WAYPOINT menu

2.Select L/L from the MODE field.

3.Select WPT NO.

4.Press [-] (turn off) or [+] (turn on), enter waypoint number to turn on/off.

5.Press the [ENT] key.

4-6

Page 53

Image 53

Furuno GD-3300, GP-3300 manual Turning Specific Waypoint Displays On/Off

Contents

Page 00080834300 Safety Instructions Furuno agent or dealer About the TFT LCD Table of Contents Video Pilot Display Navigation Data Display External Event Mark Target Mark Lines 12.1 Preventive Maintenance 12-1 12.2 Chart Symbols, Contour Lines AttributesTime Differences Geodetic Chart List 11.9 Memory Capacity Word to Furuno GD-3300/GP-3300 Owners Foreword Vii Features Viii Menu Tree GPS Antenna Unit GPA-017S System Configuration Control Description Operational Overview Control description Inserting Chart Cards Turning the power on Turning the Power On/Off Turning the cursor on/off TrackballCursor Returning Own Ship Marker to Screen Center Shifting the DisplayCursor information +36 44.257’ N Selecting Screen Center by Cursor Position How to select screen center Display Brilliance and Key Backlighting Chart Scale Displaying an electronic chart with the power turned on Card Drives, Chart CardsInsert chart card label side up in the lower slot Card drives Chart card troubleshooting Ejecting the chart cardCare and handling of the cards Press the eject button Table below shows Furuno chart symbols and their meanings Chart iconsFuruno chart symbols Buoy, lighthouse data display on Navionics charts Comparison of FURUNO, Navionics chart cards Data Window Data shown when cursor is on Plot mode description Data shown when cursor is offVideo pilot mode description Nav data mode description Menu operation versus key operation Menu Operation Main menu description Main menu description Selecting options Operation on the DisplayEntering data Summary of menu operation Operational Status Icons Economy Mode +36 44.257’ N 140.50 35.92NM 134 40.719’ E Plot Mode DisplaysPlot display when cursor is on 36 44.257’ N Plot display when cursor is off 22 Initial Settings menu Setting the Time and Date 340.5 TrackStopping Track Recording Press MENU, 9 and 1 to display the EDIT/TRACK Mark menu Track ColorChanging Color, Appearance of Specific Track EDIT/TRACK Mark menu Deleting track by color Deleting TrackDeleting specific track with cursor, box cursor Press MENU, 9, 1 to display the EDIT/TRACK menu Delete Track display Deleting all track How the track is drawn Track Plotting IntervalPlot interval and track reconstruction Plot interval by time or distance Setting plot interval 2 to time Setting plot interval 1 by time Customizing the Hold Function Turning off track display when track is not being recordedConnecting track after restarting track recording Customizing the Plot Intvl Key Setup for manually entering plot intervalTuning off a plot interval Page Entering Marks MARKS, LinesEntering marks with the cursor Entering marks at own ship’s position Press the Mark Color key to show the Change Mark Color menu Changing Current Mark Color Changing Shape, Color of Specific Marks Deleting specific marks Deleting MarksDeleting all marks Deleting marks with the cursor Target Mark External Event MarkLines Erasing an external event mark Deleting lines Entering a lineChanging line color Waypoints Waypoints Place the data input cursor on waypoint Entering WaypointsWaypoint entry by L/L coordinates Waypoint entry by cursor Waypoint entry by range and bearing Waypoint entry at own ship’s position Waypoint entry by navigation aid Entering a Comment for a Waypoint Turning Specific Waypoint Displays On/Off Deleting waypoints by cursor Deleting Waypoints Destination Waypoint Setting destination waypoint by cursorDeleting waypoints through waypoint list Deleting external waypoint Setting destination waypoint by range and bearing Setting destination waypoint by waypoint number 11 How a destination waypoint is shown on the display When you set a destination waypoint 36 34.000’ N Displaying range and bearing to destination waypoint134 20.524’ E Press the Plot key to display the Data Display Cancelling destination waypoint through the menu Cancelling Destination WaypointCancelling destination waypoint by key input Select Cancel from the Dest field Press the ENT key Sample route Route Navigation Creating routes through the route list Creating Routes Press the Route key to display the Route NO. menu Creating routes with waypoint numbers Menu keyCreating routes with waypoint numbers Route key Press the Route to display the Route NO. menu Creating routes with the cursorSelect WPT no Enter waypoint numbers Press the ENT key About route navigation Following a Route Temporarily Deselecting a Route Waypoint Example of when to deselect waypoints Deleting specific route waypoints Deleting Route Waypoints Deleting all route waypoints Cancelling Route Navigation 10 Route list Route Calculation Arrival alarm AlarmsArrival Alarm, Anchor Watch Alarm Alarm range of arrival alarm Anchor watch alarm XTE alarm XTE Alarm, Border AlarmBorder alarm Press ← twice Ship’s Speed Alarm Silencing the alarm buzzer When the Alarm Buzzer SoundsWhat alarm is sounding? Video Pilot Display FeaturesCompares the features of the video pilot and plot displays Mark data Destination data 34 44.463’ Comparison of plot and video pilot displays34 44.463’ N 135 21.288’ E Navigation Data Display 44 N 135 21 E Autopilot Data Features Available with Autopilot Connection Sample autopilot information on plot display Autopilot Information on Plot Display 134 40.719’ E 10.0KTS Autopilot Information on Video Pilot Display Autopilot in Auto mode Autopilot in Manual mode Autopilot on, destination waypoint selected Autopilot in NAV mode Press the 3 key to select Save Data to Memory Card Memory Card OperationsFormatting Memory Cards Saving Data to Memory Cards Save Track display File name example Playing Back Memory Cards Saving initial settings Saving, Playing Back Initial SettingsPlaying back initial settings Press the 5 key to select Display Memory Card Deleting track, marks/lines from a memory card Editing Memory CardsDeleting files Adding track, marks/lines GPS Information on the Navigation Data Display GPS Receiver Operation GP-3300GPS receiver status 10-1 10-2 Satellite scheduleFrequency deviation 10-3 GPS and Dgps Initial SettingsSatellite data 10-4 GPS initial settings menu descriptionDescribes the GPS Initial Settings menu Press Menu and 8, and then press − to set the cursor on Satellite Force Health/Deselection10-5 Speed and course GPS smoothing GPS SmoothingLatitude and longitude GPS smoothing 10-6 10-7 Setting GPS smoothing 10-8 Cold Start Geodetic Datum Selecting chart systemCorrecting GPS Position 10-9 Displaying Position in Loran TDs Other FunctionsDisplaying position in Loran a TDs 11-1 11-2 Bearing Display ReferenceDisplaying position in Loran C TDs 11-3 Magnetic DeviationDisplaying true bearing 11-4 Changing Chart Appearance 11-5 Correcting Chart PositionCorrecting chart position by cursor 11-6 Correcting chart position by latitude and longitudeCorrections chart position by Δ Delta L/L 11-7 Cancelling chart position correctionLoran TD Correction 11-8 Calculating R/B Between Two PointsCalculating R/B by latitude and longitude 11-9 Calculating R/B by waypoint numbers Locking or unlocking preferred settings Locking Preferred SettingsDefault memory arrangement is as shown in Figure Memory Capacity 11-11 When the track memory becomes full oldest track is deletedTrack memory Apportioning the Memory When the mark memory becomes full no marks can be enteredMark/line memory 11-12 11-13 Reading Number of Track, Marks Used 11-14 Smoothing 11-15 Selecting Navaid 11-16 Track, Mark and Marker Attributes 11-17 Initial settings menuSpecial menu 11-18 Customizable items on the Initial Settings menu Select item and option as appropriate Press the ENT key Chart Symbols, Contour Lines Attributes11-19 12-1 Maintenance & TroubleshootingPreventive Maintenance Self test at power on Diagnostic TestsMemory circuits, I/O ports 12-2 To escape from the test, press any key Keyboard test12-3 Test pattern 2 color distortion Test pattern 1 color dropout12-4 Check the pattern for color dropout Press any key to escape 12-5 Error Messages Memory card replaced during operation 12-6No file by that name exists No files on memory card to delete Waypoint being used as destination waypoint Replacement of Fuse12-7 12-8 Replacement of BatteriesMemory card battery Plotter section Verifying Program Version NoGPS section GP-3300 12-9 12-10 Troubleshooting Table 12-11 12-12 Clearing Memories Press the 8 key to select Clear Memory 12-13 Time Differences Appendix Adindan Geodetic Chart List GD/GP-3300 Specifications of Color Video PLOTTER/COLOR GPS Plotter Coating Color Index-1 Index Index-2 Index-3