Storage Manager Module, Removing the Module | Galaxy Metal Gear 65

Galaxy 65 User Guide

7.12.2 Ops Panel

The Ops Panel is an integral part of the enclosure chassis assembly and can only be replaced by trained personnel.

7.12.3 Storage Manager Module

Please refer to the Galaxy 65 Getting Started Manual (P/N 44521-01A) for full information on installing the Storage Manager module.

Important Fitting of a RAID controller to the LRC module is a factory only operation.

7.12.3.1Removing the Module

Warning Do not remove this module unless a replacement can be immediately added. The system must not be run without all modules in place.

Note As there should always be two SM modules installed, you can continue working while replacing the faulty module.

1Ensure that you correctly identify the faulty module from the two modules installed.

2Using two hands, grasp each latch between the thumb and forefinger of each hand. Squeeze thumb and forefinger together to release the latch. Pull the latches forward to cam the module out of the enclosure (Figure 7–5).

Figure 7–5Removing a Storage Manager Module (1)

3Grip the latch handles and withdraw the SM module (Figure 7–6).

72

Image 92

Galaxy Metal Gear 65 manual Storage Manager Module, Removing the Module

Contents

Galaxy 65 User Guide Acknowledgments Contents Operation Troubleshooting and Problem Solving Managing Disk Drives & Enclosures Accessing Disk Array Administrator Software Array Basics Creating and Managing Arrays & Partitions 105 Managing Disk Drives and Enclosures 173 Index 229 Galaxy 65 User Guide Potential for Radio Frequency Interference PrefaceInternational Standards Safety European Regulations Preface Class 1 Laser Product Battery SafetyLaser Safety Rack System Precautions ESD Precautions Related Documentation Data SecuritySpecial Tools and Equipment Resulting in injury or death ConventionsConvention Definition Bold Revision History Version Date Description of Change14 amended 10 planned deleted Preface Xvii Galaxy 65 User Guide Xviii Introduction Galaxy 65 System Enclosure Core Product Enclosure Chassis Tower Option 3Galaxy 65 Enclosure Chassis Rear Power Supply/Cooling Module Plug-in Modules Operators Panel Multiple Power Supply/Cooling ModulesOps Panel Indicators and Switches Switch Function Recommended Definition Number Setting Loop Resiliency Circuit Input/Output Module FC-AL 7LRC Panel Layout 8Galaxy 65 LRC Storage Manager I/O Module Drive Carrier Module 10Drive Carrier Module Visible and Audible Alarms Drive Status IndicatorsDummy Carrier Modules Anti-tamper Locks Installing your Galaxy 65 Subsystem Galaxy 65 Technical SpecificationDimensions Weight Environment PSU Safety and EMC CompliancePower Cord Drive Carrier Module Specification Interfaces RAID Card Galaxy 65 FC-AL LRC I/O Module SpecificationSoftware Enclosure Services SES Support Power On Before You Begin Power Supply/Cooling Module LEDs Ops Panel LEDs Any PSU fault or Fan fault Over or Under temperatureIntermittent Ops to ESI Communications failed Audible alarm Invalid address mode setting Disk Drives LEDs Power Up/DownStarting the Drives Managing Arrays and Partitions Using SAM Galaxy 65 RAID Management Managing Arrays Viewing Array and Drive Status Information Resetting All Statistics Viewing Array and Partition Statistics Click Verify & Update Array Parity Verifying an ArrayStopping the Array Verification Process To stop the array verification process Changing Array Ownership Changing an Array NameClick Abort Array Verification Click Change Array Name Select Disk Array Config Trust Array Trusting an ArrayDeleting an Array Click Change Options Managing Partitions Viewing Partition Status InformationChanging a Partition Name Click Delete This Array Click Change Partition LUN Changing a Partition LUNClick Change Partition Name Controlling Partition Access Viewing Known WWNs Click Add New Host Creating Nicknames for Host WWNsClick Change Host Nickname Configuring InfoShield Changing the Read-Ahead Cache Size Click Delete Partition Deleting a PartitionClick Set Read Ahead Cache Size Galaxy 65 User Guide Monitoring System Status Using SAM Setting Up Remote Notification Starting and Stopping Remote Notification Setting Up the Events to be MonitoredSetting Up the E-mail Addresses Saving Log Information to a File Click Change E-mail Info Displaying Overall Statistics Resetting the All Statistics Galaxy 65 User Guide Configuring the Galaxy 65 System Configuring the LAN-related Settings Configuring the Telnet TimeoutConfiguring the Snmp Settings Click Change LAN Configuration Click Change System Configuration Configuring the System InformationSetting Passwords Configuring the Security Options Click Change Date/Time Changing the Date and TimeUnderstanding LUNs and Viewing LUN Information Changing the Alarm Mute Setting Changing Management LUNsViewing LUN Information Click Change Management LUN Alarm threshold What to do when the alarm sounds Click Change Configuration Enabling and Disabling the Battery Changing the Utility Priority Pausing I/O Rescanning All Ports Saving and Restoring a Configuration File Saving a Configuration FileRestoring a Configuration File To restore a configuration file Click Restore Configuration File Click Continue Restoring Default Settings Viewing and Restoring Default SettingsViewing Default Settings Click Load Software Package File Click Proceed with Code UpdateUpdating Software Galaxy 65 User Guide Managing Disk Drives Displaying Disk Drive Information Clearing Metadata from a Disk Drive Displaying All DevicesViewing Disk Drive Status Click Clear Metadata from Selected Device Click Change Disk Option Configuration Enabling and Disabling Write-back CacheDisplaying Disk Drive Cache Status Enabling and Disabling Smart Changes Blinking a Drive LED Taking Down a Disk DriveClick Blink Selected Device LED Click Down Selected Drive Testing a Disk Drive Setting the EMP LUNManaging Enclosures Click Test Unit Ready Changing the Additional EMP Setting Click Update EMP Configuration Initial Start-up Problems Overview LEDs Ops Panel LED Test Mode Audible AlarmAudible Alarm Mute Troubleshooting System Address Hub Green Cooling Symptom Cause Action System FaultsPower Supply/Cooling Faults Thermal Control State Green Amber Drive Carrier Module FaultsThermal Alarm Auto Start Failure Dealing with Hardware FaultsContinuous Operation During Replacement Problem SAM page help is not displaying Host Fibre Channel ProblemsProblem SAM pages do not display properly Array Problems Changing the Backoff Percent Using SAMProblem Array is much smaller than it should be To change the backoff percentage Galaxy 65 Subsystem Problems 12.1 Power Supply/Cooling ModulesReplacing a Module Removing a PSU Module 2Removing/Inserting a Power Supply/Cooling Module 3Removing a Power Supply/Cooling Module Storage Manager Module Removing the Module 6Removing a Storage Manager Module Battery Replacement Insertion/Removal of SFP Modules Removal and Replacement 8Storage Manager Module Battery Assembly Location Terminal Emulator and COM Port Problems Problem Galaxy 65 Subsystem failed the onboard memory testProblem One of the Post diagnostic tests failed Problem Screen continuously puts out garbage characters Problem Screen looks correct, but clock is not being updated Event Definition Recommended Action Array Critical Other WWN Errors SYS Online Fail Collecting Debug Logs Setting Up and Viewing the Debug LogSummary of Debug Log Capabilities Disk Array Administrator on Controller B Utilities Menu Configuring Debug LogsDisk Array Administrator on Controller a Utilities Menu Using the Loader Diagnostics Menu Using SAM to Set Up and View the Debug LogUsing the Disk Array Administrator to Set Up Debug Logging To set up debug logging Using the Loader Utility Menu Understanding Disk-related ErrorsDisk Errors Sense Key Description Descriptions Disk Channel ErrorsError Code Description Voltage and Temperature Errors and Warnings Slow Write Performance Spare Parts and Ancillary Items Upgrading Your LRC I/O Modules Switch Function Recommended Definition Number Setting Array Basics Application RAID level Array Types RAID 0 Striped DisksRAID 1, RAID 10 Mirrored Disks RAID Volume Sets Comparing RAID Levels RAID Level Min No. Drives Description Strengths Weaknesses Array Basics Galaxy 65 User Guide Accessing Disk Array Administrator Software SettingValue Setting Value Accessing DAM Using the Ethernet Port for the First Time Accessing the Disk Array Software Using the Ethernet Port 100 Press Esc, CTRL-Z, or ← Navigating the Disk Array Administrator SoftwareDo this Changing the Screen Display Select Function Disk Array Administrator Menu Tree System Menu 2Menu Tree sheet Creating Arrays RAID level Minimum Maximum Number Drives Creating a Single-Partition Array To create a single-partition array 107 See , Array Basics, on page 89, for more information 109 110 Creating a Multiple-Partition Array To create a multiple-partition array 112 113 114 115 116 To view the status of an array Viewing Array and Drive Status InformationViewing Array Status Select Array Status and press Enter Viewing Drive Status To view drive status Stopping the Array Initialization Process Select Drive Status and press EnterTo stop the array initialization process Select Abort Initialization and press Enter Select Add a Partition and press Enter Adding a PartitionTo add a partition Galaxy 65 User Guide 123 124 To view verification status Viewing Verification StatusStopping the Verification To stop the verification process Reconstructing an ArrayExpanding Array Capacity RAID level Number of drives you can add Number of drivesTo expand an array Select Expand Function and press Enter 128 To change an array name Viewing Expand StatusTo view expand status To trust an array Select Switch Array Owner and press EnterTo change array ownership To delete an array 132 Understanding Partitions Partition 1 Free space Viewing Partition Status To view the status of a partition From the Array Menu From the All Partitions MenuPartitions Menu and press Enter Enter Viewing Partition Statistics To view the partition statistics Resetting Partition Statistics To reset partition statistics Expanding a Partition To expand a partition To change a partition LUN To change the read-ahead size Enabling or Disabling Write-back Cache To enable or disable write-back cache 5InfoShield example To view known WWNs Select General InfoShield and press Enter Select Display Host List and press Enter To create or change nicknames for WWNs 148 To set up InfoShield Changing All Partitions to Include All Hosts To delete a partition Galaxy 65 User Guide 152 Monitoring System Status Introduction Displaying the Event Log Viewing the Most Recent Event Select View Event Log and press Enter Viewing One Event at a TimeTo view one event at a time Viewing a Whole Screen of Events To view a whole screen of events Capturing the Event Log To capture the event log file Displaying Module Status Information To display module status information Displaying Hardware Configuration Information Group Field What displays Disk EMP To display hardware information only To display hardware and configuration information 163 Displaying Drive Errors Resetting Error Statistics Select Dump Debug Info and press Enter To display drive errors To access the read/write histogram Resetting Overall StatisticsTo access the overall array statistics Managing Spares Managing Dedicated Spares Adding a Dedicated SpareDeleting a Dedicated Spare To add a dedicated spare To enable dynamic spares Enabling Dynamic Spares Managing the Spare Pool Displaying the Spare Pool Adding a Spare to the Spare PoolDeleting a Spare from the Spare Pool Galaxy 65 User Guide 172 Managing Disk Drives and Enclosures Displaying Drive Information Displaying All Drives To display all drives 176 To clear metadata from a drive Displaying Drive Errors and Resetting Error StatisticsClearing Metadata from a Drive To change the write-back cache setting Displaying Disk Cache Status To display disk cache status 180 To enable or disable Smart changes To take down a drive Taking Down a DriveTo blink a drive LED from the Drive Utilities Menu Testing a Drive To test a drive To change the EMP LUN 185 Select the option or number you want to use To change the EMP settings Galaxy 65 User Guide 188 Configuring the Galaxy 65 Subsystem To shut down and restart the current SM Shutting Down and Restarting the Storage Manager ModuleShutting Down and Restarting the Current SM Module Shutting Down the Other SM Module Select Shutdown/Restart and press Enter Shutting Down Both SM Modules Other Controller Menu 193 To set an SM module’s time Configuring the Host Channels Host channel Description Setting To configure the host channels Target ID To view LUN information 198 Configuring the FC Disk Channels To configure the FC disk channels 201 Galaxy 65 CPU temperature VCC voltage To enable or disable the alarm Voltage Same as above for the VCC voltage Locking the Cache Setting To lock the cache setting To change the battery setting To change the utility priority Select Utility Priority and press Enter Rescanning All Channels To rescan all channels To pause I/O Restoring Default Settings To restore the default settings Updating Firmware Updating the SM, SM Loader and Memory Controller Firmware Updating LAN Firmware To upgrade the LAN Subsystem’s firmware LAN Configuration Configuring the SM for TCP/IP To set the IP address, subnet mask, or gateway Configuring the LAN SettingsConfiguring the IP Settings To set the FTP settings Configuring the FTP SettingsConfiguring the Telnet Settings To set the Telnet settings To set the Snmp settings Configuring the Contact Settings To set the contact settings Configuring the Http Settings To set the Http settings Resetting the LAN Subsystem To reset the LAN SubsystemSelect Reset LAN Subsystem and press Enter To change any of the security options Galaxy 65 User Guide 220 Glossary 222 223 224 Glossary Small form-factor pluggable SFP Type of connector 227 Galaxy 65 User Guide 228 Index 164 Partitions 31 Disk drives ESD Http LED Number of Drives screen 108 Setting up for SAM 218 SAM 171 Defined 167 Deleting dedicated 168 Deleting pool Stopping the process