GE GFK-0787B user manual Data Table Numbers, Contains, Range for Start Value, Range for End Value

7

Data Table Numbers

Table

11

Contains

DigitalInput Discrepancy faults

Range for Start Value

Greater than or equal to the first digital input address for A, B, or C.

Range for End Value

Less than the start plus the maximum digital input ad- dress for A, B, or C.

14	Digital Input Autotestfaults	start>=1	end<=12228,	end<=start
15	Digital Input Genius faults	start>=1	end<=12228,	end<=start
16	Digital Input Point faults	start>=1	end<=12228,	end<=start
21	Digital Output Discrepancy faults: PLC A	start>=1	end<=12228,	end<=start
22	Digital Output Discrepancy faults: PLC B	start>=1	end<=12228,	end<=start
23	Digital Output Discrepancy faults: PLC C	start>=1	end<=12228,	end<=start
24	Digital Output Autotestfaults	start>=1	end<=12228,	end<=start
25	Digital Output Genius faults	start>=1	end<=12228,	end<=start
26	Digital Output Point faults	start>=1	end<=12228,	end<=start
27	Digital Logon faults (PLC A)	First group number required	Last group number required
28	Digital Logon faults (PLC B)	First group number required	Last group number required
29	Digital Logon faults (PLC C)	First group number required	Last group number required
31	Analog Input Discrepancy faults	Greater than or equal to the	Less than the start plus the
		first digital input address for A,	maximum digital input ad-
		B, or C.	dress for A, B, or C.
35	Analog Input Genius faults	start>=1	end<=8192,	end<=start
36	Analog Input Point faults	start>=1	end<=8192,	end>=start
37	Analog Input Low Alarms	start>=1	end<=8192,	end>=start
38	Analog Input High Alarms	start>=1	end<=8192,	end>=start
45	Analog Output Genius faults	start>=1	end<=8192,	end>=start
46	Analog Output Point faults	start>=1	end<=8192,	end>=start
47	Input shutdown timers (per block)	High byte contains rack num-	High byte contains the number
	Returns a single word indicating the shutdown	ber (0±7) and low byte con-	1. Low byte contains the Serial
	timer value as seconds of elapsed time. A value	tains slot number (1±9)	Bus Address (SBA) of the de-
	of ±1 means a fault exists but the timer has not		sired block you want shut-
	started (the Shutdown Cancel bit is On).		down information from (0±28)
48	Output shutdown timers (per block)	High byte contains rack num-	High byte contains the number
	Returns a single word indicating the shutdown	ber (0±7) and low byte con-	1. Low byte contains the Serial
	timer value as seconds of elapsed time. A value	tains slot number (1±9)	Bus Address (SBA) of the de-
	of ±1 means a fault exists but the timer has not		sired block you want shut-
	started (the Shutdown Cancel bit is On).		down information from (0±28)
49	Input shutdown timers (per GBC)	High byte contains rack num-	unused
	For each SBA, returns a word indicating the	ber (0±7) and low byte con-
	shutdown timer value as seconds of elapsed	tains slot number (1±9) where
	time. A value of ±1 means a fault exists but the	the desired Bus Controller is
	timer has not started (the Shutdown Cancel bit	located.
	is On). A value of 0 means a block does not exist
	or has no associated shutdown timer. All output
	blocksreturn the value 0.

50

1000h

Output shutdown timers (per GBC)

For each SBA, returns a word indicating the shutdown timer value as seconds of elapsed time. A value of ±1 means a fault exists but the timer has not started (the Shutdown Cancel bit is On). A value of 0 means a block does not exist or has no associated shutdown timer. All input blocksreturn the value 0.

Configurationtextdescription

High byte contains rack num- ber (0±7) and low byte con- tains slot number (1±9) where the desired Bus Controller is located.

unused

unused

unused

GFK-0787B Chapter 7 Programming Information 7-25