Three Sensors to Three Blocks Triple Bus | GE GFK-0787B instruction

8

Input Wiring (continued)

Three Sensors to Three Blocks (Triple Bus)

PLC A

PLC B

PLC C

P C G G G S P B B B U C C C

A B C

P C G G G S P B B B U C C C

A B C

P C G G G S P B B B U C C C

A B C

6.2V Zener Diodes for Line Monitoring (optional)

DC+

I1

I15/32

O16

DC+

I1

I15/32

O16

DC+

Input 1

Input 15 or 32

Input 1

Input 15 or 32

Input 1

I1

Input 15 or 32

I15/32

O16

H 6.2 volt Zener diodes are used for optional line monitoring on circuits configured as tristate inputs. This option is only available with 16-circuit DC blocks.

H All blocks in an input group must have the same number of circuits (either 16 or 32).

H On either 16-circuit or 32-circuit blocks, circuit 16 is used as an output if the block group is configured for input autotesting.

H On any block, circuits that are not configured as part of the GMR input group can be used as non-redundant inputs or outputs.

H All blocks in the input group must be assigned the same serial bus address.

H If the block group is configured for input autotesting, it must be wired appropriately. Each input that is configured (by the GMR Configuration Software) to be autotested must have its input device wired to receive power from output Q16 of the block group, as shown above.

H Isolation diodes must also be wired as shown above for any input to be autotested.

	The suggested diode is 1N5400 or equivalent.
GFK-0787B	Chapter 8 Installation Information	8-5

Image 186

GE GFK-0787B user manual Three Sensors to Three Blocks Triple Bus

Contents

GE Fanuc Automation GFL±002 Preface Preface Related Publications Contents Chapter Configuration Appendix a TÜV Certification Appendix B Maintenance Override Chapter Introduction Components of a GMR System Series 90-70 PLCs Inter-processor Communications Busses and Bus Controllers Additional Bus Controllers for Communications Operation Overview Input Subsystem PLC Subsystem Voting on Input Data PLC Subsystem Providing Output Data Output SubsystemAutomatic System Test Analog, RTD, and Thermocouple Blocks Genius I/O BlocksDiscrete Blocks Block Summary Number of Non-GMR I/O Available for the 789 CPU Number of I/O Points in a GMR SystemNumber of Non-GMR I/O Available for the 788 CPU 798 Configuration and Programming GMR Basic Steps of Configuration and Programming Chapter Input Subsystem Overview GMR Input Groups One sensor to one Genius input Non-Voted I/O in the Input Subsystem Inputs from single-block simplex GMR input groupsInputs from non-GMR I/O blocks Discrete Input Processing Discrete InputsTypes of Blocks in the Input Subsystem Discrepancy Reporting for GMR Inputs Input Autotest for GMR Inputs Calculating Voltage Drops on Tristate Inputs Normally-open Inputs Line Monitoring for Discrete InputsNormally-closed Inputs Input Filter Time Manual Input Controls Number of Input Sensors per Voted Channel Analog InputsVoted Analog Inputs Analog Voting Adaptation Analog Discrepancy Reporting Non-Voted Analog Inputs in GMR Input GroupsNon-GMR Analog Blocks Chapter Output Subsystem Types of Blocks in the Output Subsystem Duplex Default for Outputs GMR Output HandlingOutput Voting Results of Block Group Voting with Three PLCs Online Output Fault Reporting PLC Logon Control Block Output Groups Output Load Sharing Electrical Characteristics of Sink and Source Blocks Operation of a 4-Block Output GroupBus Redundancy in a 4-Block Output Group Manual Output Controls and Diagnostics GMR Mode Redundancy Modes for Output Blocks Hot Standby Mode Basic Hot Standby Mode OperationHot Standby Mode in a GMR System Chapter PLC Subsystem System Startup All GMR bus controllers at serial bus address Online Changes Data Initialization CPU Sweep in a GMR System PLC Operation Estimating CPU Sweep Time Sweep Time Contribution of Genius I/O and GBCsImportant Note Input Processing DiscrepanciesDiscrete Inputs Discrete Input Voting Voting with Three Discrete Inputs Voting with Two Discrete Inputs Voting for One Discrete Input Analog Inputs Analog Input Voting Voting for Three Analog Inputs Voting for Two Analog Inputs Voting for One Analog Input Output Processing Discrete Outputs Shutdown Synchronous or Asynchronous Input Autotest and I/O Shutdown M12265 ± Sdcan Cancel I/O Shutdown Output Faults that Cause I/O ShutdownM12244 ± Iosd Any I/O Shutdown Timer Activated Programming for I/O Shutdown Hours Shut Down Recovery Shut Down Prevention Entering, Clearing, or Setting Global Data Communications Between PLCsGlobal Data Redundancy Chapter Diagnostics Programming for Diagnostics Diagnostics in a GMR System Input DiagnosticsOutput Diagnostics CPU Redundancy Mode Configuration Block Type Setting Up Blocks to Report Genius FaultsSetting Up Other Blocks to Send Multiple Fault Reports Summary Table GMR Autotesting Autotest Sequence Configuration Required for Discrete Input Autotest Setup for Input AutotestDiscrete Input Autotest Operation of the Input Autotest Circuit Fail Mask Discrete Output Autotest Operation of the Discrete Output Autotest Block a Pulse-tested Pulse Test Operation Input Data GMR Discrepancy ReportingDiscrete Input Discrepancy Reporting Voted Discrepancy Inputs Discrete Output Discrepancy Reporting How Output Discrepancy Checking is PerformedDiscrete Output Discrepancy Reporting with Dynamic Outputs Analog Input Discrepancy Reporting Input Line Fault Detection in a GMR Application PLC and I/O Fault Tables in a GMR System Clearing the Fault Tables in a GMR System Fault Table Messages for GMR Reporting of No-Load Faults on 4-Block Output Groups Fault Description Code Hex Meaning Fault Specific DataFault Type for Output Autotest PLC Fault Table Messages for GMR CodeMessage Code Code 10903 Code Manual Output Controls and Diagnostics Monitoring Manual Output Controls Fault, No Fault, and Alarm Contacts Discrete Input Fault Contacts for GMR Discrete Output Fault Contacts for GMR Contact References Associated with an Output ShortCircuitfault Overtemperaturefault Overloadfault Fault Contacts for Analog Inputs Analog Fault and Alarm Contacts for GMRAlarm Contacts Fault Contacts for Analog Outputs Chapter Configuration Configuration Overview Basic Steps of Configuration For Information to be copied set only Configuration to yes Using the GMR Configuration Software GMR Configuration Software Revision and Checksum Installing the Configuration Software Getting Started Mouse and Keyboard Guide for the Configuration Software Using a Mouse Configuration GMR Configuration Summary Insert the first GBC bus controller group Opening a Previously-Saved Configuration File Creating/Selecting a File Saving a Configuration File Closing a Configuration File without Saving It Changing to Another Directory Starting a New Configuration Closing and Deleting the System Configuration FileEntering a System Description GMR Configuration Selections When you select System, the following menu appears CPU Configuration SimplexShutdown Test Interval Period Input Discrepancy Filter Limits Initialization Data + %R data needed for the application SpareGlobal Data Initialize Data GBC1 GBC2 Parame Comment Ters Fault Actions M12232M12234 Write Access Adding Bus Controllers and I/O Modules Genius Bus Controller Group Configuration Exiting the Window Configuring the Input Subsystem for a Bus Controller Group Select To ConfigureExiting a Block Group Window Start %I SBA Auto Test GFK-0787B Duplex State GFK-0787B Analog I/O Group Configuration Vote Adapt Mode Vote Adaptation Default State Analog Discrepancy Thresholds and Limits Configuring the Output Subsystem for a Bus Controller Group Start %Q GFK-0787B Options Start Ref Bus C inputs Reserved inputs Configuration References are 0001 to CONFIG4 Creating the GMR10 Output File Printing the GMR Configuration Completing the Logicmaster 90 Configuration Configuring Bus Controllers Creating and Copying the PLC Configuration Logicmaster Configuration Summary GFK-0787B Configuring GMR Bus Controllers and I/O Blocks Setting Up Blocks for Fault Reporting Configuring Genius I/O BlocksCopying Configurations Editing the Reference Addresses Device Configuring 16-Circuit and 32-Circuit Discrete DC BlocksFeature Circuit or Factory Selections Block Setting Serial bus Circuit I/O Type Report Faults Block I/O Type Baud Rate Pulse Test Input Filter Time Configuration Duplex Default Duplex Output Default State Setting Block Duplex Voted Output Default State Setting Block Results of Block Voting with Only Two PLCs Online Chapter Programming Overview Estimating Bus Scan Time Program Instruction Set for GMREstimating Memory Usage Use of Do I/O and Suspend I/O Memor y Write Access Reserved ReferencesReferences Reserved For Input and Output Addressing for GMR Discrete I/O Addressing Q1009 to %Q1024 I1009 to %I10241024 ± 16 ± 3 x 32 +1 = 913 = %I0913 Analog I/O Addressing AnalogOutput Addressing Example16 x 6 = 96 words required Register %R Memory Assignment for GMR Memory Required for Startup Initialization Data Monitoring the Fault Tables System Status %S ReferencesMonitoring Forces and Overrides GMR Status and Control %M References Status References Resetting Status Flags PLC OK Flags Control References M12257 ContinueReference Nickname Description Meaning Clearing the PLC Fault Tables 40-characterConfiguration File DescriptionM12262 Report Programming for Startup Monitoring Startup Status Enabling Outputs At Startup Powerup Note Performing I/O Fault Reset These Program Blocks represent logic Fault. If both are not 1, initialization continuesExample Ladder Logic Routines that are appropriate for Application When a third PLC comes on line Triplex bit is optional the need for this bit depends on Point Faults Enabling I/O Point FaultsProgramming for I/O Shutdown Clearing Faults Associated with Fault/No Fault Contacts Programming for Fault and Alarm ContactsFault and No Fault Contacts Fault-Locating References Discrete Input Fault Contacts for GMR Discrete Output Fault Contacts for GMR Analog Fault Contacts for GMR Analog Alarm Contacts for GMR Reading GMR Diagnostics Parameters for the Call FunctionY3 dummy not used Range for Start Value Data Table NumbersContains Range for End Value Error Codes for GMR Diagnostics Code Meaning Programming for Global Data Global Data for the Application Program GFK-0787B Adding GMR10 to the Logicmaster Librarian Select F6 Add Element to Library Do not Rename GMR10 Storing a Program to the PLC GFK-0787B Using the Store Function Field Description Storing an Identical Program Following CPU Replacement Storing a Revised Program Using the Program Download Utility Using the Download Utility with the Default PLC IDsPress the Space Bar to Continue Customizing the Download Utility for Other PLC IDs Processing Complete Programming Information GFK-0787B Chapter Installation Information Genius Bus Connections Termination Boards Input Wiring Single Sensor to Three Blocks Triple Bus Three Sensors to Three Blocks Triple Bus Block Wiring for 16-Circuit Source Block in an Input Group DC Source Block IC660BBD020 Block Wiring for 16-Circuit Sink Block in an Input Group DC Sink Block IC660BBD021 Block Wiring for 32-Circuit Source Block in an Input Group DC Source Block IC660BBD024 Block Wiring for 32-Circuit Sink Block in an Input Group DC Sink Block IC660BBD025 Output Wiring for a 16-Circuit, 4-Block Group Circuit, 4-Block Output Group Block Wiring for a 16-Circuit 4-Block Output Group Block a Output Autotest and Pulse Testing OFF±ON±OFF TestON±OFF±ON Test GE Catalog Number CR7RBXXEL Spectra 700 IEC Control Relay Output Wiring for a 32-Circuit, 4-Block Group Block Wiring for a 32-Circuit 4-Block Output Group Block a GFK-0787B Milliamp Appendix TÜV Restrictions Catalog Number Firmware Description Revision Level Appendix a TÜV Certification COMMREQ, DATAINITCOMM, Call SUB, Callexternal Appendix Maintenance Override Project engineer Projectengineer, Typeapproval Recommendations Index Index-2 Index-3 Index-4