Control Panel, Reset Button | HandHeld Entertainment SV Series

2

Control Panel

The control panel displays the reset button, I/O connector, system LEDs, and the serial port connector.

Reset Button

The Reset button is multifunctional. It may be used to turn off the laser beam, perform calibration, and reset the ports.

Turn Off Laser Beam

The laser beam may be turned off (therefore turning off the SV unit’s operation) by holding down the Reset button for a few seconds until the beam turns off. Pressing the Reset button again will begin normal operation.

Note: There are some modes of operation when the laser beam is on only during specific scanning times. (See the ~SA command (page 6-24) in Chapter 6, SV Command Language) Using the Reset Button for turning off the system is not recommended in these modes.

Perform Calibration

The reset button is used in the calibration procedures. See "Calibration" on page 5-8for details.

Reset Ports

Pressing the Reset button will reset ports to their inactive states. This is useful in systems where the SV unit is holding a printer in PAUSE mode and the user desires to clear the pause condition. See "Output Ports" on page 2-5for details.

I/O Connector

The I/O connector is used for all power and field interconnections. The connector is a DB 15 male. Pin-outs are shown below:

1 -	Isolated synchronization input (+)

2 - Isolated synchronization input (-)

3 - GND

4 - Switch synchronization input

5 - Output Port 1

6 - Output Port 2

7 - Output Port 3

8 - Output Port 4

Quick Check® SV Series User’s Guide

2 - 1

Image 13

HandHeld Entertainment SV Series manual Control Panel, Reset Button, Connector

Contents

User’s Guide Disclaimer FCC Class B Compliance Statement Statement of Agency ComplianceCanadian Notice SV Series Use with UL-listed Equipment Statement of RoHS ComplianceLaser Beam Enclosure Description Laser SafetyPage Table of Contents Scanner Setup ISO Parameter Grade Thresholds Technical Specifications Chapter a SV Series Setup Hints Scanning Distance and Angle Introduction Quick Check SV Series ScanView Software SV Series Model SpecificationsLaser Beam SV100 Connector Reset ButtonControl Panel Sync Inputs + 5 VDC Power Input Isolated Sync Input Diagram Envelope Sync Mode Edge Sync Mode Output Ports Communication Sync Commands Indicator LEDs 1 Power/Sync LEDSystem Displays Calibration LED Serial Port Specifications Serial Port ConnectorSerial Port Pin-out Serial Port Transmission Format Pos Chars Parameters + or indicating sign of avg. max. bar Symbology Identifier Table UPC-A Quick Check SV Series User’s Guide ScanView Software Installation ScanView Installation and SetupSystem Requirements PC Communication Port Setup Software Operation Warnings Setup MenuTitle Bar Screen Display Menu Bar Screen Display Static Codes Mode Select SymbologiesMoving Codes Mode Ladder Mode and Picket Fence Mode Support Menu Advanced MenuAbout Menu Item All Data Points, Last 64 Data Points Speed Button Bar Screen DisplayZoom Erase Current Session Data Session Mode Transmit SV CommandsSession Mode Notes Modes Of Operation Analysis Screens Reflectance Profile ModeBar Code Analysis Screen Bottom Panel Bar Code Analysis Screen Graph Display Area Bar Code Analysis Results for a Previous Bar CodeRight Panel Reflectance Profile Screen Color Coding Reflectance Profile Screen Scanner Setup Scanner Positioning Bar Code Travel Direction SV Scanner/Verifier Setup ProcedureBar Code Travel Speed Considerations Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Good Reflectance Profile Bad Reflectance Profile Picket Fence Direction Setting Ladder Mode Scanning Length Using ScanView Software Picket Fence Bar Code Positioning SpecificationsCalibration Ladder Direction Procedure Adjusting Scanner Gain and Offset Desired Signal Amplitude and Placement Quick Check SV Series User’s Guide Data Match Commands B SV Command Language Check for specific data ~BCa##bc…bbb……mmm……bbb…… etc. up to 32 characters max ~ Brnbb .. + Define increment or decrement data check Examples Decrementing Examples Incrementing Examples Diagnostic Commands D Relationship Between ~BC and ~Br CommandsGet the Scan Rate Example return using ScanView Hardware Configuration Commands H~HB# ~HO# Operational Mode Example return using ScanView inputted ~HB5 Display the verifier parameters ~HQ# Transmission Mode Quick Check SV Series User’s Guide ~Hdx01nnn Sets scanner gain or offset ~LA## Overall passing grade Label Setup Commands L~LD## Passing percent decode ~LE# ~LFxy Analyze special subsymbology parameters ~LL ~LI# Include the specified symbology for a label Quick Check SV Series User’s Guide ~LQ# Enable or Disable Port Activations by Partial Decodes ~LT# Sync Input Source ~LS## Set minimum number of scans for valid read ~LX# Sync Type ~LV## Output Interface Mode~LZ## Set Number of Codes per Label i.e., per sync period ~OS# Set Transmission Data Format Output Mode Selection Commands O ~PBpiiaaabbb Port barcode decision block parameters Output Port Setup Commands PIDs Analysis Low High Units Parameters Value PCS IDs Description Low Value High Value ~PPpiiaaa Port action parameters Port State PASS/FAIL Parameters Indicator Digit Value ~PR#### Port/LED reset state Indicator System Control Commands S Checking SV Status with ~HT How to Set Up Single Scan Operation Disable Verification Execute the calibration procedureEnable Verification ~SK# Communication Sync Operation Description Set the number of scans for Software Commanded Read Mode~SN### Raster Check ~Sh## Set the high target reflectance value for calibration Reset the System~Sl## Set the low target reflectance value for calibration Data Transmission Example ~Ssxy Command Example ~Stx Program Command Indicator Header Mode 00 ~LV00~Stx Command Example ~St5 Output Interface Modes Descriptions Mode 01 I/O operation Mode 01 ~LV01Mode 01 LED Operation SV Commands Important to Mode Mode 02 I/O operation Mode 02 ~LV02 ~LV02 Mode 02 LED Operation ~LQ0 Mode 12 ~LV12 Mode 03 ~LV03Mode 12 I/O operation ~LV12 Mode 12 LED Operation ~LDxx Mode 16 I/O operation Mode 16 ~LV16 ~LV16 Mode 16 LED Operation~PP801xxx ~PB811xxxyyy Operation Mode 17 ~LV17 LED Operation SV Commands Important for Mode~LV17 ~PB815xxx000 Mode 18 ~LV18 LED Operation ~LV18 ~PB806xxx000 Mode 19 ~LV19 ~LV19 ~LDxx Mode 20 ~LV20 ISO Parameter Grade Thresholds Reference Decode Qcolvsv Series Product Specifications Technical SpecificationsParameter Specification Scanning Performance-SV Series Model PowerScanner Options Sync Sync Mode Moving Bar Codes SymbologiesOperation Modes Outputs Parameters Analyzed Sync Mode Stationary Bar CodesNo Sync Free Scan Operation Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Maintenance Maintenance/Customer SupportCleaning Technical Assistance Online Technical Assistance For Further Information Product Service and RepairJapan Malaysia Online Product Service and Repair Assistance Limited Warranty Quick Check SV Series User’s Guide Setting the Proper Scan Distance Session Mode Screen Showing the X Dimension Measurement Setting the Proper Scan Angle Button Example of Good Scan Profile Examples of Scan Profile Parameters Out of Range Calibration Hints Quick Check SV Series User’s Guide Page Hand Held Products, Inc