+ 5 VDC Power Input, Sync Inputs | HandHeld Entertainment SV Series

9	-	Reserved
10	-	Reserved
11	-	GND
12	-	+5 VDC power in
13	-	Power GND
14	-	GND
15	-	Output Port 5

+ 5 VDC Power Input

The SV Series requires + 5 Volts DC, +/- 0.25 Volt. Maximum current consumption is 1 amp. The voltage input must be connected to pin 12 and the ground input should be connected to pin 13 on the I/O connector.

The alternate ground pins (3, 11, and 14) may be used for power ground or for connecting the ground(s) of an external device(s) (such as presence sensors) that may be powered from a different source than the verifier power input.

Sync Inputs

Utilizing a sync signal is recommended for all applications using hardware (as opposed to communication) interfaces. (See "SV Command Language" on page 6-1.) A sync signal is used to synchronize the SV Series to an object, label, etc. that contains the bar code(s) being analyzed as it passes through the laser beam. The SV Series should be programmed for the number of bar codes expected per sync interval. This ensures a robust system that can report all undetectable bar codes due to printer failure, missing labels, etc., along with quality and data information on bar codes that are fully or partially decoded.

Two hardware sync inputs are available. Pin 4 is designed to be used with TTL or open collector inputs. For open collector inputs, adding an external pull-up resistor to 5 VDC is recommended because the internal pull-up is a relatively high 100K ohm resistance. Pins 1 and 2 form a ground isolated input designed to be used with systems that need separate grounds than the verifier and/or output a higher voltage level than TTL. See the figures the follow for circuit diagrams.

2 - 2

Quick Check® SV Series User’s Guide

Image 14

HandHeld Entertainment SV Series manual + 5 VDC Power Input, Sync Inputs

Contents

User’s Guide Disclaimer Canadian Notice Statement of Agency ComplianceFCC Class B Compliance Statement Laser Beam Statement of RoHS ComplianceSV Series Use with UL-listed Equipment Laser Safety Enclosure DescriptionPage Table of Contents Scanner Setup ISO Parameter Grade Thresholds Technical Specifications Chapter a SV Series Setup Hints Scanning Distance and Angle Quick Check SV Series Introduction Laser Beam SV Series Model SpecificationsScanView Software SV100 Control Panel Reset ButtonConnector + 5 VDC Power Input Sync Inputs Isolated Sync Input Diagram Edge Sync Mode Envelope Sync Mode Communication Sync Commands Output Ports System Displays Power/Sync LEDIndicator LEDs 1 Calibration LED Serial Port Pin-out Serial Port ConnectorSerial Port Specifications Serial Port Transmission Format Pos Chars Parameters + or indicating sign of avg. max. bar Symbology Identifier Table UPC-A Quick Check SV Series User’s Guide System Requirements ScanView Installation and SetupScanView Software Installation PC Communication Port Setup Title Bar Screen Display Setup MenuSoftware Operation Warnings Menu Bar Screen Display Moving Codes Mode Select SymbologiesStatic Codes Mode Ladder Mode and Picket Fence Mode About Menu Item Advanced MenuSupport Menu Zoom Speed Button Bar Screen DisplayAll Data Points, Last 64 Data Points Erase Current Session Data Session Mode Notes Transmit SV CommandsSession Mode Modes Of Operation Bar Code Analysis Screen Reflectance Profile ModeAnalysis Screens Bar Code Analysis Screen Bottom Panel Right Panel Bar Code Analysis Results for a Previous Bar CodeGraph Display Area Color Coding Reflectance Profile Screen Reflectance Profile Screen Scanner Setup Scanner Positioning Bar Code Travel Speed Considerations SV Scanner/Verifier Setup ProcedureBar Code Travel Direction Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Good Reflectance Profile Picket Fence Direction Bad Reflectance Profile Calibration Picket Fence Bar Code Positioning SpecificationsSetting Ladder Mode Scanning Length Using ScanView Software Ladder Direction Procedure Adjusting Scanner Gain and Offset Desired Signal Amplitude and Placement Quick Check SV Series User’s Guide SV Command Language Data Match Commands B ~BCa##bc…bbb……mmm……bbb…… etc. up to 32 characters max Check for specific data Examples ~ Brnbb .. + Define increment or decrement data check Incrementing Examples Decrementing Examples Get the Scan Rate Relationship Between ~BC and ~Br CommandsDiagnostic Commands D ~HB# Hardware Configuration Commands HExample return using ScanView Example return using ScanView inputted ~HB5 ~HO# Operational Mode ~HQ# Transmission Mode Display the verifier parameters Quick Check SV Series User’s Guide ~Hdx01nnn Sets scanner gain or offset ~LD## Passing percent decode Label Setup Commands L~LA## Overall passing grade ~LFxy Analyze special subsymbology parameters ~LE# ~LI# Include the specified symbology for a label ~LL Quick Check SV Series User’s Guide ~LQ# Enable or Disable Port Activations by Partial Decodes ~LS## Set minimum number of scans for valid read ~LT# Sync Input Source ~LZ## Set Number of Codes per Label i.e., per sync period ~LV## Output Interface Mode~LX# Sync Type Output Mode Selection Commands O ~OS# Set Transmission Data Format IDs Analysis Low High Units Parameters Value Output Port Setup Commands P~PBpiiaaabbb Port barcode decision block parameters PCS ~PPpiiaaa Port action parameters IDs Description Low Value High Value Port State PASS/FAIL Parameters ~PR#### Port/LED reset state Indicator Digit Value System Control Commands S Indicator How to Set Up Single Scan Operation Checking SV Status with ~HT Enable Verification Execute the calibration procedureDisable Verification ~SK# Communication Sync ~SN### Set the number of scans for Software Commanded Read ModeOperation Description Raster Check ~Sl## Set the low target reflectance value for calibration Reset the System~Sh## Set the high target reflectance value for calibration ~Ssxy Command Example Data Transmission Example ~Stx Command Example ~St5 Mode 00 ~LV00~Stx Program Command Indicator Header Output Interface Modes Descriptions Mode 01 LED Operation Mode 01 ~LV01Mode 01 I/O operation SV Commands Important to Mode Mode 02 ~LV02 Mode 02 I/O operation Mode 02 LED Operation ~LV02 ~LQ0 Mode 12 I/O operation Mode 03 ~LV03Mode 12 ~LV12 Mode 12 LED Operation ~LV12 ~LDxx Mode 16 ~LV16 Mode 16 I/O operation ~PP801xxx Mode 16 LED Operation~LV16 ~PB811xxxyyy Mode 17 ~LV17 Operation ~LV17 SV Commands Important for ModeLED Operation ~PB815xxx000 Mode 18 ~LV18 LED Operation ~LV18 ~PB806xxx000 Mode 19 ~LV19 ~LV19 ~LDxx Mode 20 ~LV20 ISO Parameter Grade Thresholds Reference Decode Parameter Specification Technical SpecificationsQcolvsv Series Product Specifications Scanner Options PowerScanning Performance-SV Series Model Sync Operation Modes SymbologiesSync Mode Moving Bar Codes Outputs No Sync Free Scan Operation Sync Mode Stationary Bar CodesParameters Analyzed Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Cleaning Maintenance/Customer SupportMaintenance Technical Assistance Japan Product Service and RepairOnline Technical Assistance For Further Information Malaysia Limited Warranty Online Product Service and Repair Assistance Quick Check SV Series User’s Guide Setting the Proper Scan Distance Setting the Proper Scan Angle Session Mode Screen Showing the X Dimension Measurement Button Example of Good Scan Profile Calibration Hints Examples of Scan Profile Parameters Out of Range Quick Check SV Series User’s Guide Page Hand Held Products, Inc