Mode 18 ~LV18, ~Ln## | HandHeld Entertainment SV Series specs

~LN##

This command sets the minimum number of codes to be read during a sync period. ## = the number of codes. For example: ~LN02 causes a No Read condition to be set if less than 2 bar codes are fully decoded during a sync interval. See the ~LZ## (page 6-17) command below for priority.

If the value ## = 00 (and ~LZ00 is also set), a sync input is disregarded, therefore a No Read condition is disabled.

~LZ##

This command sets the exact number of codes to be read during a sync period.

##= the number of codes. For example: ~LZ02 causes a No Read condition to be set if exactly 2 bar codes are not fully decoded during a sync interval.

This command overrides the ~LN## command if the number of codes set does not = 00. If ~LZ## is set to ~LZ00, the ~LN## command takes precedence.

~Hx

This command stores all parameters into non-volatile memory. This command should be the last command sent after parameters are programmed via the above commands.

Mode 18 (~LV18)

I/O operation

1.System will operate Envelope or Edge sync mode (~LX#)

2.Sync polarity – programmable (~LP#)

3.Use ~PR0210 for proper port initialization.

4.Port 1 will go active OFF (no current) on an error condition.

5.Port 2 will go active ON (sink current) on an error condition.

6.Port 3 will operate in per analysis pulse mode. Active polarity ON (sink current), approximately 500 millisecond duration. Port 3 will activate (pulse) on an error condition.

7.Port 4 will operate in per analysis pulse mode. Active polarity ON (sink current), approximately 50 millisecond duration. Port 4 will activate (pulse) on an error condition.

8.Port 5 will pulse active ON for an acceptable condition (absence of error condition.)

9.Port 5 pulse time programmable (~PP801xxx). Pulses will act like a re- triggerable 1-shot.

10.Pushing the reset button or power re-cycle will place Ports 1- 5 in their inactive states.

Quick Check® SV Series User’s Guide

6 - 45

Image 93

HandHeld Entertainment SV Series manual Mode 18 ~LV18, ~Ln##

Contents

User’s Guide Disclaimer Statement of Agency Compliance FCC Class B Compliance StatementCanadian Notice Statement of RoHS Compliance SV Series Use with UL-listed EquipmentLaser Beam Enclosure Description Laser SafetyPage Table of Contents Scanner Setup ISO Parameter Grade Thresholds Technical Specifications Chapter a SV Series Setup Hints Scanning Distance and Angle Introduction Quick Check SV Series ScanView Software SV Series Model SpecificationsLaser Beam SV100 Reset Button ConnectorControl Panel Sync Inputs + 5 VDC Power Input Isolated Sync Input Diagram Envelope Sync Mode Edge Sync Mode Output Ports Communication Sync Commands Indicator LEDs 1 Power/Sync LEDSystem Displays Calibration LED Serial Port Specifications Serial Port ConnectorSerial Port Pin-out Serial Port Transmission Format Pos Chars Parameters + or indicating sign of avg. max. bar Symbology Identifier Table UPC-A Quick Check SV Series User’s Guide ScanView Installation and Setup ScanView Software InstallationSystem Requirements PC Communication Port Setup Software Operation Warnings Setup MenuTitle Bar Screen Display Menu Bar Screen Display Static Codes Mode Select SymbologiesMoving Codes Mode Ladder Mode and Picket Fence Mode Advanced Menu Support MenuAbout Menu Item All Data Points, Last 64 Data Points Speed Button Bar Screen DisplayZoom Erase Current Session Data Session Mode Transmit SV CommandsSession Mode Notes Modes Of Operation Reflectance Profile Mode Analysis ScreensBar Code Analysis Screen Bottom Panel Bar Code Analysis Screen Bar Code Analysis Results for a Previous Bar Code Graph Display AreaRight Panel Reflectance Profile Screen Color Coding Reflectance Profile Screen Scanner Setup Scanner Positioning SV Scanner/Verifier Setup Procedure Bar Code Travel DirectionBar Code Travel Speed Considerations Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Good Reflectance Profile Bad Reflectance Profile Picket Fence Direction Setting Ladder Mode Scanning Length Using ScanView Software Picket Fence Bar Code Positioning SpecificationsCalibration Ladder Direction Procedure Adjusting Scanner Gain and Offset Desired Signal Amplitude and Placement Quick Check SV Series User’s Guide Data Match Commands B SV Command Language Check for specific data ~BCa##bc…bbb……mmm……bbb…… etc. up to 32 characters max ~ Brnbb .. + Define increment or decrement data check Examples Decrementing Examples Incrementing Examples Relationship Between ~BC and ~Br Commands Diagnostic Commands DGet the Scan Rate Hardware Configuration Commands H Example return using ScanView~HB# ~HO# Operational Mode Example return using ScanView inputted ~HB5 Display the verifier parameters ~HQ# Transmission Mode Quick Check SV Series User’s Guide ~Hdx01nnn Sets scanner gain or offset Label Setup Commands L ~LA## Overall passing grade~LD## Passing percent decode ~LE# ~LFxy Analyze special subsymbology parameters ~LL ~LI# Include the specified symbology for a label Quick Check SV Series User’s Guide ~LQ# Enable or Disable Port Activations by Partial Decodes ~LT# Sync Input Source ~LS## Set minimum number of scans for valid read ~LV## Output Interface Mode ~LX# Sync Type~LZ## Set Number of Codes per Label i.e., per sync period ~OS# Set Transmission Data Format Output Mode Selection Commands O Output Port Setup Commands P ~PBpiiaaabbb Port barcode decision block parametersIDs Analysis Low High Units Parameters Value PCS IDs Description Low Value High Value ~PPpiiaaa Port action parameters Port State PASS/FAIL Parameters Indicator Digit Value ~PR#### Port/LED reset state Indicator System Control Commands S Checking SV Status with ~HT How to Set Up Single Scan Operation Disable Verification Execute the calibration procedureEnable Verification ~SK# Communication Sync Operation Description Set the number of scans for Software Commanded Read Mode~SN### Raster Check Reset the System ~Sh## Set the high target reflectance value for calibration~Sl## Set the low target reflectance value for calibration Data Transmission Example ~Ssxy Command Example ~Stx Program Command Indicator Header Mode 00 ~LV00~Stx Command Example ~St5 Output Interface Modes Descriptions Mode 01 ~LV01 Mode 01 I/O operationMode 01 LED Operation SV Commands Important to Mode Mode 02 I/O operation Mode 02 ~LV02 ~LV02 Mode 02 LED Operation ~LQ0 Mode 03 ~LV03 Mode 12 ~LV12Mode 12 I/O operation ~LV12 Mode 12 LED Operation ~LDxx Mode 16 I/O operation Mode 16 ~LV16 Mode 16 LED Operation ~LV16~PP801xxx ~PB811xxxyyy Operation Mode 17 ~LV17 SV Commands Important for Mode LED Operation~LV17 ~PB815xxx000 Mode 18 ~LV18 LED Operation ~LV18 ~PB806xxx000 Mode 19 ~LV19 ~LV19 ~LDxx Mode 20 ~LV20 ISO Parameter Grade Thresholds Reference Decode Technical Specifications Qcolvsv Series Product SpecificationsParameter Specification Scanning Performance-SV Series Model PowerScanner Options Sync Sync Mode Moving Bar Codes SymbologiesOperation Modes Outputs Sync Mode Stationary Bar Codes Parameters AnalyzedNo Sync Free Scan Operation Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Maintenance Maintenance/Customer SupportCleaning Technical Assistance Online Technical Assistance For Further Information Product Service and RepairJapan Malaysia Online Product Service and Repair Assistance Limited Warranty Quick Check SV Series User’s Guide Setting the Proper Scan Distance Session Mode Screen Showing the X Dimension Measurement Setting the Proper Scan Angle Button Example of Good Scan Profile Examples of Scan Profile Parameters Out of Range Calibration Hints Quick Check SV Series User’s Guide Page Hand Held Products, Inc