HandHeld Entertainment SV Series specs

[~SN###]#scans= 050 [~Lp#]part= 000 [~Lt#]itfp= 001 [DACs]= 175 156 255 255 [~LQ#]p_out= 000 [~Lw,d]def= 000 000 [~L*]pnet= 000 [~LC##]I25min= 002 [~H###]NTrys= 010 [~OS#]Data_Output= 000 [~Hs#]RunSpeed= 000 [~SS######]CntlChars=01 3 010 {hex 5}

T

~Hdx01nnn

Sets scanner gain or offset.

x = value of 1 or 2. If =1, scanner gain is set. If = 2, scanner offset is set.

nnn = gain or offset setting.

For gain, the higher the value, the higher the gain. 225 is the max allowed value.

Example: ~Hd101195 sets the scanner gain setting to a value of 195.

For offset, the higher the value, the lower the offset.

Example: ~Hd201145 sets the scanner offset value to 145.

These commands are best used in conjunction with Hand Held Products’ ScanView software. Please refer to Chapter 4 for descriptions on the use of these commands.

~Hnx

Sets the number of consecutive scans that do not detect a bar code that cause a bar code to exit the beam and be reported.

x = values of 2, 3, 4 or 5. The normal setting is 5.

This command is best used in conjunction with the ~SB 1 setting for single scan operation. Please see ~SBn (page 6-24) command description.

~Hx

Saves the parameters to FLASH (non-volatile memory) from RAM.

6 - 10

Quick Check® SV Series User’s Guide

Image 58

HandHeld Entertainment SV Series manual ~Hdx01nnn Sets scanner gain or offset

Contents

User’s Guide Disclaimer FCC Class B Compliance Statement Statement of Agency ComplianceCanadian Notice SV Series Use with UL-listed Equipment Statement of RoHS ComplianceLaser Beam Laser Safety Enclosure DescriptionPage Table of Contents Scanner Setup ISO Parameter Grade Thresholds Technical Specifications Chapter a SV Series Setup Hints Scanning Distance and Angle Quick Check SV Series Introduction Laser Beam SV Series Model SpecificationsScanView Software SV100 Connector Reset ButtonControl Panel + 5 VDC Power Input Sync Inputs Isolated Sync Input Diagram Edge Sync Mode Envelope Sync Mode Communication Sync Commands Output Ports System Displays Power/Sync LEDIndicator LEDs 1 Calibration LED Serial Port Pin-out Serial Port ConnectorSerial Port Specifications Serial Port Transmission Format Pos Chars Parameters + or indicating sign of avg. max. bar Symbology Identifier Table UPC-A Quick Check SV Series User’s Guide ScanView Software Installation ScanView Installation and SetupSystem Requirements PC Communication Port Setup Title Bar Screen Display Setup MenuSoftware Operation Warnings Menu Bar Screen Display Moving Codes Mode Select SymbologiesStatic Codes Mode Ladder Mode and Picket Fence Mode Support Menu Advanced MenuAbout Menu Item Zoom Speed Button Bar Screen DisplayAll Data Points, Last 64 Data Points Erase Current Session Data Session Mode Notes Transmit SV CommandsSession Mode Modes Of Operation Analysis Screens Reflectance Profile ModeBar Code Analysis Screen Bar Code Analysis Screen Bottom Panel Graph Display Area Bar Code Analysis Results for a Previous Bar CodeRight Panel Color Coding Reflectance Profile Screen Reflectance Profile Screen Scanner Setup Scanner Positioning Bar Code Travel Direction SV Scanner/Verifier Setup ProcedureBar Code Travel Speed Considerations Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Good Reflectance Profile Picket Fence Direction Bad Reflectance Profile Calibration Picket Fence Bar Code Positioning SpecificationsSetting Ladder Mode Scanning Length Using ScanView Software Ladder Direction Procedure Adjusting Scanner Gain and Offset Desired Signal Amplitude and Placement Quick Check SV Series User’s Guide SV Command Language Data Match Commands B ~BCa##bc…bbb……mmm……bbb…… etc. up to 32 characters max Check for specific data Examples ~ Brnbb .. + Define increment or decrement data check Incrementing Examples Decrementing Examples Diagnostic Commands D Relationship Between ~BC and ~Br CommandsGet the Scan Rate Example return using ScanView Hardware Configuration Commands H~HB# Example return using ScanView inputted ~HB5 ~HO# Operational Mode ~HQ# Transmission Mode Display the verifier parameters Quick Check SV Series User’s Guide ~Hdx01nnn Sets scanner gain or offset ~LA## Overall passing grade Label Setup Commands L~LD## Passing percent decode ~LFxy Analyze special subsymbology parameters ~LE# ~LI# Include the specified symbology for a label ~LL Quick Check SV Series User’s Guide ~LQ# Enable or Disable Port Activations by Partial Decodes ~LS## Set minimum number of scans for valid read ~LT# Sync Input Source ~LX# Sync Type ~LV## Output Interface Mode~LZ## Set Number of Codes per Label i.e., per sync period Output Mode Selection Commands O ~OS# Set Transmission Data Format ~PBpiiaaabbb Port barcode decision block parameters Output Port Setup Commands PIDs Analysis Low High Units Parameters Value PCS ~PPpiiaaa Port action parameters IDs Description Low Value High Value Port State PASS/FAIL Parameters ~PR#### Port/LED reset state Indicator Digit Value System Control Commands S Indicator How to Set Up Single Scan Operation Checking SV Status with ~HT Enable Verification Execute the calibration procedureDisable Verification ~SK# Communication Sync ~SN### Set the number of scans for Software Commanded Read ModeOperation Description Raster Check ~Sh## Set the high target reflectance value for calibration Reset the System~Sl## Set the low target reflectance value for calibration ~Ssxy Command Example Data Transmission Example ~Stx Command Example ~St5 Mode 00 ~LV00~Stx Program Command Indicator Header Output Interface Modes Descriptions Mode 01 I/O operation Mode 01 ~LV01Mode 01 LED Operation SV Commands Important to Mode Mode 02 ~LV02 Mode 02 I/O operation Mode 02 LED Operation ~LV02 ~LQ0 Mode 12 ~LV12 Mode 03 ~LV03Mode 12 I/O operation Mode 12 LED Operation ~LV12 ~LDxx Mode 16 ~LV16 Mode 16 I/O operation ~LV16 Mode 16 LED Operation~PP801xxx ~PB811xxxyyy Mode 17 ~LV17 Operation LED Operation SV Commands Important for Mode~LV17 ~PB815xxx000 Mode 18 ~LV18 LED Operation ~LV18 ~PB806xxx000 Mode 19 ~LV19 ~LV19 ~LDxx Mode 20 ~LV20 ISO Parameter Grade Thresholds Reference Decode Qcolvsv Series Product Specifications Technical SpecificationsParameter Specification Scanner Options PowerScanning Performance-SV Series Model Sync Operation Modes SymbologiesSync Mode Moving Bar Codes Outputs Parameters Analyzed Sync Mode Stationary Bar CodesNo Sync Free Scan Operation Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Cleaning Maintenance/Customer SupportMaintenance Technical Assistance Japan Product Service and RepairOnline Technical Assistance For Further Information Malaysia Limited Warranty Online Product Service and Repair Assistance Quick Check SV Series User’s Guide Setting the Proper Scan Distance Setting the Proper Scan Angle Session Mode Screen Showing the X Dimension Measurement Button Example of Good Scan Profile Calibration Hints Examples of Scan Profile Parameters Out of Range Quick Check SV Series User’s Guide Page Hand Held Products, Inc