Honeywell K14114 3/06 Rev.B setup guide Dialer Programming

			LYNXR-I Installation and Setup Guide
			Data Field Descriptions
✻34	Exit Delay		The system will wait the time entered before sounding an
	00-99 = exit delay time in seconds		alarm if the exit door is left open after the system has been
			armed.
			UL installations: must be set for a maximum of 60 seconds
✻35	Entry Delay 01		The system will wait the time entered before sounding alarm upon
	00-99 = entry delay time in seconds.		entering if system is not disarmed. UL installations: must be set for a
			maximum of 45 seconds
✻36	Entry Delay 02		The system will wait the time entered before sounding alarm
	00-99 = entry delay time in seconds.		upon entering.
			UL installations: must be set for a maximum of 45 seconds
✻37	Audible Exit Warning/Quick Exit		Exit Warning: Sound consists of slow continuous beeps until
	Exit Warning	Quick Exit	last 5 seconds, when it changes to fast beeps. The warning
			sound will end at the termination of exit delay.
	0 = no exit warning	0 = no quick
			Quick Exit: If enabled, user can restart the exit delay time after
	sound	exit
			arming in STAY mode by entering the user code and pressing
	1 = provide exit	1 = allow quick
			the STAY key, or by pressing the STAY key if Quick Arm is
	warning sound	exit	enabled. This avoids having the user disarm then re-arm the
	when armed AWAY
			system after allowing someone to enter or exit
✻38	Confirmation of Arming Ding		Confirmation of arming is provided by a 1/2 second external sounder
	0 = no ding		“ding” that sounds when closing report is sent, or at the end of exit delay.
	1 = confirmation ding after arming system		If Option 2 is selected the external sounder “ding” occurs immediately
	2 = confirmation ding after arming from RF button or RF
			after the system receives the RF transmission.
	keypad only
✻39	Power Up In Previous State		When the system powers up armed, an alarm will occur 1
	0 = always power up in a disarmed state		minute after arming if a zone is faulted, and any bypassed
	1 = assume the system status prior to power-down		zones will be unbypassed.
			Note: If the previous state was armed AWAY or STAY, the
			system will not respond to sensor changes for 1 minute,
			which allows time for sensors such as PIRs to stabilize.
			UL installations: must be 1 (power up in previous state)

DIALER PROGRAMMING (✻40–✻50)

Fields ✻40, ✻41, ✻42: Enter up to the number of digits shown. Enter 0–9, # + 11 for ‘*’; # + 12 for ‘#’; # + 13 for a pause (2 seconds)

NOTE: Whenever AAV is used, primary (field ✻41) and secondary (field ✻42) phone numbers should be preceded with the call waiting disable command. Otherwise, there is the possibility of connection of the third party to LYNXR-I during AAV mode.

✻40	PABX Access Code	If fewer than 6 digits need to be entered, exit by pressing [✻].
	Enter up to 6 digits if PABX is needed to access an	To clear entries from field, press ✻40✻.
	outside line.
✻41	Primary Phone No.	If fewer than 20 digits entered, exit by pressing [✻]. To clear
	Enter up to 20 digits.	entries from field, press ✻41✻.
		Note: Backup reporting (8 attempts are made to the secondary
		phone number if no kissoff is received after 8 attempts to
		the primary number) is automatic only if there is a
		secondary phone number (field ✻42).
✻42	Secondary Phone No.	If fewer than 24 digits entered, exit by pressing [✻]. To clear
	Enter up to 24 digits.	entries from field, press ✻42✻. See backup reporting note for
		field ✻41. If using the paging feature, enter the pager phone
		number here.

- 21 -