Honeywell K14114 3/06 Rev.B Data Field Descriptions, LYNXR-IInstallation and Setup Guide

LYNXR-I Installation and Setup Guide

Data Field Descriptions

To ensure that the LYNXR-I properly transmits its reports to the Central Station via the proper channel you must program a Primary Phone Number in Field *41 and/or activate/deactivate the LRR/IP Communications Module in Field *55.

The 15-Second Dialer Delay (Burglary), programmed in Field in *50 is independent of the delay selected in Field *77 and applies to both telephone and communications device.

DYNAMIC SIGNALING DELAY/DYNAMIC SIGNALING PRIORITY FIELD ✻77

Two report channels are used by the LYNXR-I to support the LRR/IP communications device and dynamic signaling. For the primary channel the device can communicate via LRR, Cellular GSM, or Internet (IP). Secondary phone is not affected by dynamic signaling scheme. Two programming options are used to define dynamic signaling behavior. Field *55 is used to enable/disable the LRR/IP communications device and allows it to supervise the communications module. The two-digit option programmed in Field *77 defines how dynamic signaling will function. The Dynamic signaling options are shown below:

	Enable/Disable	Dynamic Signaling Delay/Dynamic Signaling
Reporting Option	Device (Field *55)	(Field *77)
Primary Phone only	0 = Disable	1st Entry
Report is sent to Primary phone with No Dynamic Signaling		Enter Any Digit
Delay		2nd Entry
		Enter “0”
LRR/IP Communications Device only	1 = Enable	1st Entry
Report sent to communications device with No Delay		* = enter any non zero digit as a first entry
		2nd Entry
		2 = LRR/IP reporting only
Redundant reports to both channels	1 = Enable	1st Entry
Report independently goes to the Primary phone and LRR/IP		0 = Redundant reporting on dialer and comm. device
communications device with No Delay		2nd Entry
		* = enter any number as a second entry
Primary Phone is the preferred channel	1 = Enable	1st Entry
First report is sent to the primary phone. If primary phone fails to		* = enter a delay for the first entry
deliver report within the delay window defined in *77 all following		2nd Entry
reports go to both primary phone and communications device		0 = Primary Dialer is the preferred channel
with no delay. When report goes through the primary phone,
LYNXR-I stops reporting to communications device.
Note: The delay must be set to at least 30 seconds if Remote
Phone Control and/or AAV is enabled.
LRR/IP Communications Device is the preferred channel	1 = Enable	1st Entry
First report is sent to the communications device. If device fails to		* = Enter any delay for the first entry
deliver report within to deliver report within the time window		2nd Entry
defined in *77 all following reports go to both LRR/IP device and		1 = LRR/IP is the preferred channel
primary phone with no delay. When report goes through the
LRR/IP device LYNXR-I stops reporting to primary phone.

Note: If the LRR/IP communications device is selected as the preferred channel option and the LYNXR-I detects a communication failure or supervision failure, reports will be sent to the Primary Phone without any delay.

✻77	Dynamic Signaling Delay/ Dynamic			Intended for use with LRR/IP communication device reporting.
	Signaling Priority			This field’s 1st Entry allows you select the time the panel will
	1st Entry (delay before switching Central Station			wait for acknowledgment from the first reporting destination
				(preferred channel) before it attempts to send a message to the
	reporting path)		7 = 105 seconds	second destination. This delay is per message. The 2nd entry
	0	= Redundant reporting		allows you to select the preferred reporting channel.
		on dialer and LRR/IP	8 = 120 seconds
				Notes: (1)	You must also enable/disable LRR/IP Device in field *55.
		communications	9 = 135 seconds	(2)	If Remote Phone Access is enabled, and Primary Phone is
		device	#10 = 150 seconds		used as a Preferred Channel, Dynamic Signaling Delay
	1	= 15 seconds	#11 = 165 seconds		should be at least 30 sec in order to prevent duplicate
	2	= 30 seconds	#12 = 180 seconds		reports.
	3	= 45 seconds	#13 = 195 seconds	(3)	For UL installations Dynamic Signaling Delay cannot exceed
	4	= 60 seconds	#14 = 210 seconds		15 sec. If Primary Phone is used as a Preferred Channel,
	5	= 75 seconds	#15 = 225 seconds	1st Entry	duplicate reports may sent.
	6	= 90 seconds
				Enables Dynamic Signaling Delay. The entry of digits 1-9 or #10-
	2nd Entry			#15 will control the time-out period the panel will wait for an
				acknowledgment from the first reporting destination. Delays can
	0 = Primary Dialer Preferred Channel
				be selected from 0 to 225 seconds, in 15-second increments. If 0
	1 = LRR/IP Preferred Channel
				is entered, the control panel will send redundant reports to both
	2 = LRR/IP reporting only
				Primary Dialer and the LRR/IP communications device.
				2nd Entry
				The second entry determines the Dynamic Signaling Priority.
				The alternate Central Station communication path will be
				initiated After the time-out period.

- 26 -