Honeywell K14114 3/06 Rev.B Enhanced Zone Programming Mode, LYNXR-IInstallation and Setup Guide

LYNXR-I Installation and Setup Guide

	56 Enhanced Zone Programming Mode
✻
			Enroll mode	If “L” is displayed, the serial number for this transmitter has already
	IA	LC	0 = advance to the VOICE DESCRIPTOR	been entered. It may, however, still be viewed, confirmed (only if in
				listen mode), or deleted.
			prompt (1C).
			Note: This will save all zone parameters.	View serial number
			1 = enter now and proceed to SERIAL
				Enter “3”. Each digit will be redisplayed, and the keypad will beep once
			NUMBER prompt (1b).	for digits 1-6, and three times for the last digit.
			Note: Not applicable if the serial number is already
			present.	Confirm serial number
			2 = copy the last serial number entered into	The serial number/loop number combination can be confirmed after one
				transmission from a BR type device or two transmissions (fault and
			local ram.
				restore) from a UR or RF type device. If a transmission is received that
			Note: If this is the 1st zone, none will be in the buffer
				matches the serial number and loop number entered, the system will
			and the panel will emit a long tone. Not valid if	confirm the reception by announcing the Voice Descriptor for the zone,
			serial number is already present.	if it is programmed, followed by three beeps, and a “C” will appear on
			3 = view existing serial number.	the display indicating the received serial number and loop number
			Note: Only if “L” is displayed. If “L” is not displayed,	have been confirmed. No further transmissions will be received.
			panel will emit a long beep.	Delete serial number
			9 = advance to F; delete existing serial
				The serial number can be deleted by entering “9”.
			number.
			Note: Only if “L” is displayed. If “L” is not displayed,	If “L” is not displayed, the serial number for this transmitter has not
			panel will emit a long beep.
				been previously entered. You may enter the serial number manually,
			[✻] = advance to the VOICE DESCRIPTOR
				copy the previous serial number, return to Prompt (E) or enter the
			prompt (1C). This will save all zone	serial number later using the ✻83 Enhanced Sequential Mode.
			parameters.	Manual entry
			[#] = return to the LOOP NUMBER prompt (E).
				Enter "1" to advance to Serial number prompt (1b).
			Note: In order for all entered parameters to be
				Copy the previous serial number
			accepted, you must advance to the VOICE	Enter “2” to copy the previous serial number entered.
			DESCRIPTOR prompt (1C).	Return to Prompt (E)
				Enter “#” to return to Loop Number prompt (E).
				Enter transmitter later
				Enter “0” or “✻” if you wish to enter the transmitter later, using the
				✻83 Enhanced Sequential Mode described later in this manual.
				Notes: (1) The panel will listen only when it is in the idle loop waiting
				for key entry and a serial number has been entered. If a key
				is entered, the function must be completed and the panel
				will listen again.
				(2) A long beep indicates illegal entry or duplicate serial number/loop
				entry
			Serial number	In this mode, the transmitter serial numbers can only be entered
	Ib		Enter the transmitter’s 7-digit serial number.	manually.
			[#] = return to prompt 1A and reject any serial	Enter the	7-digit serial number printed on the transmitter. If an
			numbers entries that have been made.
				incorrect digit is entered, press the [#] key to backup to prompt (1A)
			[✻] = return to prompt 1A, (if a valid serial
				and start over. When all 7 digits are entered, press the [✻] key.
			number has been entered, the "L" is
			displayed and the serial number will be	If 52 seconds passes and no entry has been made, the system returns
			copied into EEROM from the last serial	to prompt (1A).
			entered into the buffer.)	Notes: (1) If the serial and loop number combination is already
			Note: This prompt can be used only to manually
					present the keypad will emit a single long beep and the
			enroll a serial number. RF enrollment will be		system will return to the (1A) prompt and “L” will be
			rejected and the current zone descriptor will be		displayed.
			announced, followed by a single long beep	(2)	If less than 7 digits have been entered, the keypad will
			and the system will return to prompt (1A).		emit a single long beep and return to the (1A) prompt
					without displaying the “L”.
				(3)	If more than 7 digits have been entered, the first 6 digits
					will be saved along with the last digit that was entered
					(entering 123456789 yields the serial number 1234569).
			Voice descriptor	Each zone can have a voice descriptor of up to 3 words that will be
	IC		0 = skip to next zone (A)	announced whenever the system announces status for that zone.
			1 = enter descriptor mode; existing descriptor
			for this zone will be announced

- 32 -