Honeywell K14114 3/06 Rev.B setup guide Data Field Descriptions

LYNXR-I Installation and Setup Guide

Data Field Descriptions

Defaults (where applicable) are Indicated in bold text.

The following pages list all data fields in this Control (in numerical order). Use the blank programming form to record the data for this installation. Note that both keypad LEDs flash while in Programming mode.

Note: Entering a number other than the one specified will give unpredictable results.

✻20	Installer Code						The Installer Code is used to enter the 4-digit Master Security
	Enter 4 digits, 0-9						Code. See "Master Code" in the System Operation section for
							procedure.
✻21	Quick Arm Enable						If enabled, security code is not required to arm the system. The
	0	= do not allow quick arm					user simply presses and holds down the AWAY or STAY key to
	1	= allow quick arm					arm.
✻22	Keypad Backlight Timeout						This option allows the choice of either always backlighting the
	0	= no timeout; always backlight keys					keypad or turning the backlighting off after 10 seconds of
	1	= turn backlighting off after inactivity					keypad inactivity.
✻23	Forced Bypass						All zones bypassed by this function will be displayed after the
	0	= no forced bypass					bypass is initiated.
	1	= provide automatic bypass of all open (faulted) zones					UL installations: must be 0 (no forced bypass)
✻24	RF House ID Code						The House ID identifies receivers and wireless keypads.
	00 = disable all wireless keypad usage						If a 5804BD/5804BDV Transmitter is to be used, a House ID
	01-31 = House ID						Code MUST be entered, and the keypad should be set to the
							same ID.
✻25	Powerline Carrier Device (X10) House ID						Powerline Carrier Devices require a House ID. This field
	0	= A	4 = E	8 = I	# + 12 = M		identifies this House ID to the Control. The Powerline Carrier
	1	= B	5 = F	9 = J	# + 13 = N		Devices are programmed in field ✻80.
	2 = C 6 = G # + 10 = K # + 14 = O
	3 = D 7 = H # + 11 = L # + 15 = P
✻26	Chime by Zone						This option allows the installer to define the specific zones
	0	= no (chimes on fault of any entry/exit or perimeter					intended to chime when faulted while the system is in Chime
		zone when Chime mode is activated					mode. If enabled, these zones are defined in zone list 3 (see ✻81
	1	= yes (chimes on fault of those zones assigned to					Zone List Menu Mode).
		Zone List 3 when Chime mode on)
✻27	Real Time Clock Display						Refer to the User’s Manual for setting the clock time and date.
	0	= do not display the time
	1	= display the time
✻29	Daylight Savings Time Start/End Month						Enter # + 10 for 10, # + 11 for 11, and # + 12 for 12.
	0, 0 = no daylight saving time used
	1-12 = start month and end month
✻30	Daylight Savings Time Start/End Week						Enter the appropriate start and end weekend of the month.
	0	= disable			4 = fourth weekend
	1	= first weekend of month			5 = last weekend
	2	= second weekend			6 = next to last
	3	= third weekend			7 = 3rd from last
✻31	Single Alarm Sounding Per Zone						This field applies only to burglary zones (zone response types 1-
	(per armed period)						5, 10), and affects long range radio reporting but does not affect
	0	= no limit on alarm sounding per zone					central station reporting.
	1	= limit alarm sounding to once per arming period for					Note: This field applies only to the bell and does not affect
		a given zone
							keypad sounds.
							UL installations: must be 0 (no limit)
✻32	Fire Sounder Timeout						This Control complies with NFPA requirements for temporal
	0 = yes, fire sounder timeout after time programmed in						pulse sounding of fire notification appliances.
		field ✻33					Temporal pulse sounding for a fire alarm consists of the
	1	= no fire sounder timeout; continue sounding until					following: 3 pulses – pause – 3 pulses – pause – 3 pulses. . .
		manually turned off
✻33	Alarm Bell Timeout						This field determines whether the external sounder will shut
	0	= No timeout		2 = 8 min		4 = 16 min	off after time allowed, or continue until manually turned off.
	1	= 4 min		3 = 12 min			UL installations: must be set for a minimum of 4 min
							(option 1)

- 20 -