Honeywell K14114 3/06 Rev.B Data Field Descriptions, LYNXR-IInstallation and Setup Guide, Device

				LYNXR-I Installation and Setup Guide
				Data Field Descriptions
✻49	Split/Dual Reporting			This field is used to select a reporting option as follows:
				Enter: 0 - 5 when reporting to telephone receivers.
	To Primary		To Secondary
				6 - 9 when reporting to a pager is desired.
	0 = All reports		None, unless primary
				10 - 13 when reporting to an auxiliary telephone receiver.
			fails, then all
				Pager Report Format
	1 = Alarms, Restore, Cancel		Others
	2 = All except Open/Close, Test		Open/Close, Test	Options 6-9 send reports to the primary phone number, in a
	3 = Alarms, Restore, Cancel		All	format defined in Field ✻48, and send reports to a pager, which
	4 = All except Open/Close, Test		All	has its phone number entered as the secondary phone number in
	5 = All reports		All	Field ✻42. The pager report is a 7-digit code, with optional 16-
	To Primary		To Paging Number	digit prefix, in the following format:
	6 = All reports except Open/Close		Alarms, Open/Close ‡,	AAAAAAAAAAAAAAAA-EEE–0NNN where:
			Troubles	AAA = Optional 16 digits for PIN number, etc. See Field ✻88 for
	7 = All reports		Alarms, Troubles	full description of these characters.
	8 = All reports		Alarms, Open/Close ‡,	EEE = 3-digit Event Code as follows:
			Troubles	911 = Alarm (NN = zone number)
	9 = All reports except Open/Close		Open/Close ‡	101 = Open, system disarmed (NN = user no.)
				102 = Close, system armed (NN = user no.)
	To Primary		To Follow Me System	811 = Trouble (NN = zone no.)
			Phone Number	0 = Always displayed before 3-digit user/zone no.
	10=All reports except Open/Close		Alarms, Open/Close ‡,	NNN = 3-digit user number or zone number, depending on the
			Troubles	type of event (EEE) that occurred.
	11 = All reports		Alarms, Troubles	Follow Me System Report Format
	12=All reports		Alarms, Open/Close ‡,
				Options 10-13 send reports to the primary phone number, in a
			Troubles	format defined in Field ✻48, and sends voice message to the
	13=All reports except Open/Close		Open/Close ‡	secondary phone number entered in Field ✻42.
	‡ Will report Users 0, 5-8, and, if using wireless button-type			The message is a repeatable system status announcement. If the
	devices, will report the zone number of the arm or disarm			manual paging option has been programmed in Field ✻87, the
				message will repeat “system, system…..”.
	button 26-33. All other zones and users are not reported.
				The message can be terminated by pressing any key on the
				telephone keypad.
✻50	15-Second Dialer Delay (Burglary)			If enabled, provides delay of burglary report to the central station,
	0 = no dialer delay			and allows time for the subscriber to avoid a false alarm
	1 = provide 15-second delay of burglary alarm report			transmission. The delay applies only to zone type 3 and 5 alarms
	when armed away			and not to zone type 24 alarms (silent burglary) or to 24-hour zone
				types 6, 7, and 8 (silent panic, audible alarm, auxiliary alarm),
				which are always sent as soon as they occur.
				UL installations: must be 0 (no delay)
✻51	Periodic Test Report			Test report code entered in field ✻64 is sent.
	0 = no test report	2 = weekly
	1 = once every 24 hrs	3 = once every 30 days
✻52	First test Report Offset			Select the time for the first report following programming or
	0 = 24 hrs after exit program mode or download			downloading.
	1 = 6 hours after exit program mode or download
	2 = 12 hrs after exit program mode or download
	3 = 18 hrs after exit program mode or download
✻53	Sescoa/Radionics Select			If disabled, selects Radionics, which uses hexadecimal 0-9, B-F
	0 = Radionics (0–9, B–F reporting)			reporting.
	1 = SESCOA (0–9 only reporting)			If enabled, selects Sescoa, which uses only numeric reporting (0-9).
				Select 0 for all other formats.
✻54	Lack of Usage Notification			If enabled, notifies the central station if an end user is not
	0 = Disabled	4 = 90 days		operating their security system by sending a System Inactivity
	1 = 1 day	5 = 180 days		report 654. The report will be sent only to the Primary phone
	2 = 7 days	6 = 365 days		number and only if Contact ID® format was selected.
	3 = 27 days			Note: The report will follow the ✻49 = 0 rules, no matter which
	Note: There is no local annunciation indicating that this			selection was made in ✻49.
	report has been sent to the Central Station.
✻55	Enable/Disable LRR/IP Communications			This option is used to enable/disable Central Station reporting via
	Device			the LRR/IP Communications Device (See Field *77). Upload/
	0 = disable			download via the Internet IP module is not affected by this entry.
				Zone 103 supports the LRR/IP Communications Device.
	1 = enable
				Notes: (1) When LYNXR-I is in programming mode it will not
				communicate with the LRR/IP device. As a result the
				LRR/IP device will transmit 355 (event and restore)
				reports to the Central Station.
				(2) Zone 103 can not be bypassed.

- 23 -