Honeywell K14114 3/06 Rev.B Powerline Carrier Device, Programming, Device number, Device action

LYNXR-I Installation and Setup Guide

✻80 Device Programming Menu Mode

The following explains these prompts in detail. The left two columns identify the prompts and list the available entries. The right-most column provides a further explanation of the entries.

Note: Entering a number other than one specified will give unpredictable results.

		Powerline Carrier Device		Entering “1” advances to the next prompt below.
	80	programming		Entering “0” exits mode, upon which this prompt blinks, indicating
				the mode is inactive.
		0 = exit mode
		1 = enter mode
		Device number		Enter device numbers as 2-digit entries.
A	0I
		01-08 = device number to be programmed
		[✻] = continue
		00 = exit Device Programming mode
		Device action		Enter the 1-digit action (0-3) for the device being programmed
b	aa	0 = No response		(current action is displayed).
				NOTES:
		1 = Close for 2 seconds
		2 = Close and Stay Closed		1. If “3” is entered (pulse), only up to 3 different devices can be
				pulsed if one of the devices is a siren/horn (X10 Powerhouse
		3 = Continuous Pulse on & off (1 sec ON, 1 sec
				Security model SH10A). In addition, the siren/horn cannot be
		OFF)		manually activated using the lights on/lights off keypad
		[✻] = continue		commands.
		[#] = return to previous prompt		2. If using an X10 Powerhouse Security SH10A siren:
				• you must use device action “3.”
				• you must change the device action default to “3” if using default
				table 2 or 4
		Start event type		Enter the 1-digit event type (0-3) to activate the device being
C	et	0 = Not used	3 = Trouble	programmed. A zone list must be used in conjunction with an event. If
				a zone type/system operation is to be used instead of an event, enter
		1 = Alarm	[✻] = continue
				“0”.
		2 = Fault	[#] = return to previous
			prompt
		Start zone list		If a zone list will be used to start the device action, enter the zone list
d	zl	1-3 = zone list number (to be programmed in		number at this prompt.
		field ✻81)
		0 = zone list not used for this device
		[✻] = continue
		[#] = return to previous prompt
		Start zone type		If a zone type or system operation will be used to start the device
E
	zt	01-58 = zone type to start this device action		action, enter the appropriate 2-digit code for the device being
		(select only those that are applicable)		programmed (see table that follows).
		00 = zone type not used for this device			Choices for zone types
		[✻] = continue		00 = Not Used	04 = Interior Follower		08 = 24 Hr Aux
		[#] = return to previous prompt		01 = Entry/Exit #1 05 = Trouble Day/Alarm Night			09 = Fire
				02 = Entry/Exit #2	06 = 24 Hr Silent		10 = Interior w/Delay
				03 = Perimeter	07 = 24 Hr Audible		24 = Silent Burglary
				Choices for system operation
				20 = Arming–Stay		33 = Any Alarm (except	42 = Sys. Batt. Low
						zt 08 & 09)
				21 = Arming–Away		36 = At Bell Timeout**	43 = Comm. Failure
				22 = Disarm. (Code		38 = Chime	52 = Kissoff
				+ OFF)
				31 = End of Exit		39 = Any Fire Alarm	58 = Duress
				Time
				32 = Start of Entry		40 = Bypassing
				Time
				** Or at Disarming (which ever occurs earlier)
		Stop zone list		If a zone list will be used to STOP, or restore, the device action, enter
F	zl	1-3 = zone list to stop this device action		the zone list number 1, 2, or 3 (to be programmed in ✻81 mode). If not
				used, enter “0”.
		0 = zone list not used
		[✻] = continue
		[#] = return to previous prompt
		Stop zone type		If a zone type or system operation will be used to STOP the device
IA	zt	01-58 = zone type to start this device action		action, enter the appropriate 2-digit code (see the "ZT" choices listed
				above). If not, enter 00.
		(select only those that are applicable)
				The display then returns to the DEVICE NUMBER prompt (A) so
		00 = zone type not used for this device		that you can enter the next device number to be programmed, or enter
		[✻] = continue
				[0][0] to end device programming.
		[#] = return to previous prompt

- 36 -