Alarm Handling | Honeywell R0512 guide

ALARM HANDLING

EXCEL 50/100/500/600/800

are set in refresh after a short-time interruption (maximum: 2 minutes) due to a communication error.

EN2B-0092GE51 R0512

52

Image 54

Honeywell R0512 manual Alarm Handling

Contents

Excel 50/100/500/600/800 Excel 50/100/500/600/800 Contents Subtype Value Hysteresis Trend Cycle Value Write Protection Excel 50/100/500/600/800 Revision Overview ChangeSection Sensor Offset added System Overview Overview Programming Datapoints Physical Datapoints Flexible Datapoints Pseudo Datapoints Global Datapoints Data Points Mapped Datapoints V2.04.xx or higher Access Level Acknowledge Alarm V2.04.xx or higherAttributes Active State prior to Active State ExcelStatus text Alarm Delay Alarm SuppressionAlarm Status prior to Alarm Definition Alarm Status V2.04.xx or higherAlarm Type Interval Counter Alarm Status Attributes Delay Time Switching Up Delay Time Switching DownCycle Count Descriptors Feedback DelayHigh/Low Alarm/Warning Limits Engineering Unit Hours Since Serviced Hours RunHours Run Log Alarm Hysteresis Hysteresis Example of alarm hysteresis Trend Hysteresis Intrinsic Hysteresis for Analog Input Signals Broadcast Hysteresis Input/Output Status Text V2.04.xx or higher Interval Count Characteristic Interval Limit Last Change Configured Activated Or low By DIP Diagram High By @Pull-Up Resistor Handling By plug-in For DI on AI Impedance LED Mode XF823x, XFL823x, and XFx830x modules Maintenance AlarmManual Value Network Variable V2.04.xx or higher Normally Open/Normally Closed V2.04.xx or higher Off Phase Operating ModeMotor Run Time Manual value Remote valueResulting value Subtype Point AlarmsOutput Type Remote value Resulting Value Safety Position XFx822x, XFx824x, and XFx830x modules Pulse DurationScaling Factor Switching Down Sensor OffsetSuppress Point Technical Address Switch-On CounterSwitching down Switching down behavior Trend Logging Value Hysteresis Trend Cycle Number of technical addresses for flexible datapoints ValueRoom Temp.1.10 Flexible datapoint Number of technical addresses Write Protection List of Datapoint Attributes Attributes Attributes Individual Time Programs Time ProgramsStructure Daily Program Weekly Program Annual Program Generating a Time Program Special Day ListToday Function Time Programs Alarm Handling Prior to04.x Alarm Alarm text Cond Cause/reason English Code # System AlarmsSystem alarms Benefits Alarm Handling Warm Start With corresponding function of XBS or XL-Online System Alarms Suppression V .04.xx or higher User Program Alarms Alarms Sent across the System BusData Storage Alarm Handling Communication Test ModeDistributed I/O testing V2.04.xx or higher System Bus Bus Communication AccessBus Initialization Runtime Synchronization Initialization of Distributed I/O Modules New Bus DevicesNetwork-Wide Controller Time Synchronization Remote Communication PC CommunicationExcel IRC Point Refreshing Remote Modem Connection Controller Firmware 2.03.xx and Higher Remote Trending dial-upGeneral Controller Firmware 2.04.xx and Higher Excel For all other controllers equipped with Flash Eproms Customize Windows Default Regional and Language Settings HBS Country and Language SettingsMiscelleanous XL40A2MMI Care Country Controllers with Internal Text MMI XL Online CentraLine Country and Language Settings CLTG00MMI Graphic MMI CLMMI00N2x Tiger Controllers with Hex Dec Char Unicode ISO/IEC 10646-12000 Character Name Latin Small Letter L Latin Small Letter O with Diaeresis Character Settings Eastern Europe Latin Small Letter D Latin Small Letter U with Ring Above Latin Capital Letter L with Acute Character Settings Turkey Miscelleanous Latin Small Letter D Latin Capital Letter I with DOT Above Latin Capital Letter G with Breve Procedure 1. In Windows, click StartSettingsControl panel Miscelleanous Miscelleanous Miscelleanous Miscelleanous Modemfaq Index Automation and Control Solutions