Introduction to, General Modules | HP 6000 Router guide

14CHAPTER 1: INTRODUCING THE ROUTER 6000 FAMILY

Introduction to	The 6000 Routers modules include RPU, PSU (PWR), FAN, and FICs.
General Modules
	RPU The RPU functions primarily to process protocols, forward low-speed packets,
	control interfaces, and detect faults. The state monitoring information, such as the
	operation states of FAN, PWR, and system can be shown directly via the LEDs on
	the RPU, or reported to the network management system. In addition, RPU also
	provides the hardware reset button, RESET.
	Figure 4 RPU

Image 14

HP 6000 Router manual Introduction to, General Modules, Routers modules include RPU, PSU PWR, FAN, and FICs

Contents

Router 6000 Family Installation Guide Marlborough, MA 3Com CorporationCampus Drive 01752-3064 Contents Troubleshooting Application Software Upgrade Register Your Product to Gain Service Benefits Communication protocols that are used to interconnect WANs About this GuideConventions List conventions that are used throughout this guide Router RelatedDocumentation Use the display user-interface Introduction Main features of 6000 RoutersIntroducing the Router Family Abundant fault isolation methods Components Router ModelStructure Front Panel Rear Panel Rear Panel of the 3Com Router Front Panel Rear Panel of the 3Com Router 6040 6080 System descriptionSystem Description of 6040 Sdram General Modules Provides the hardware reset button, ResetIntroduction to 6000 Routers modules include RPU, PSU PWR, FAN, and FICs LED and button Description Interface Console interfaceConsole interface attributes Attribute Description AUX interface attributes AUX interfaceEthernet interface MDI LEDs Front Panel of AC Power Module PWR LED description LED Fan Location Limitation on dust content in equipment room Installing the RouterTemperature/Humidity requirements in the equipment room General Site Even the entire Router 3Com 6000 Routers and accessorie Safety RecommendationsCheck Router Accessories Name Quantity Installation Tools Meters Equipment SET Model Dimensions mm Installation6000 Router dimensions Installing Modules Various FICs Cable-retention clip Power switch AC input Connect AC Power Cord AC power supplyAC power input range 100 to 240V, 50/60Hz AC Recommended AC power socket Console cable Connect console cable Console failure, AUX can function as a console interface AUX cable Installing the Router Establishing Configuring the RouterConfiguration Environment Configuring the Router Establishing Configuration Environment Configuring the Router Display system information Select booting device and download applicationsStartup Process Self-test on Sdram Following information displays on the screen Decompress Application Router Configuration FundamentalsProcedure Initialize the system Performs the local configuration through CON port Snmp Management Slot Slot 5 Slot 7Slot 8 Slot Interface numbering rule Boot Menu Software MaintenanceSoftware Maintenance Overview Starting Boot main system Boot Sub-menuUpgrading Boot main system LargeBootrom through serial port Modifying serial port parameters Starting host program in default mode Starting application program from Flash Entering serial port sub-menu Available Boot Device wancom Entering Ethernet port sub-menu Modifying Flash description area Then the system enters boot file control menuDisplaying available boot files in the Flash Available boot files Setting the main boot fileSetting the backup boot file Returning to Boot main menu Rebooting the system Upgrading Program Files Using Xmodem ProtocolIgnoring system configuration Program Setting Parameters Xmodem File Application Program Building up upgrade environmentUpgrading Via Ethernet Port Configuring the Router Software Maintenance Hardware Hardware MaintenancePower Module Removal Right side inside the integrated chassis Install a FanFan Removal Remove a Fan Remove an RPU RPU Removal InstallationInstall an RPU Hardware Maintenance Troubleshooting TroubleshootingTroubleshooting Power System Configuration System Upgrade device of 6000 Router Troubleshooting Application Software UpgradeTroubleshooting Displays the following prompt Troubleshooting Application Software Upgrade Troubleshooting Following are the FICs available for 6000 Series Routers Flexible Interface CardsFIC Categories Port 10/100 FIC 3C13861 Make Ethernet cable Ethernet Cable Port 100 FX MM FIC SC optical fiber connector 1-port 100BASE-F SM FIC interface attributes FIC 3C13864 Port Enhanced SerialFIC 3C13863 Attribute Description Synchronous Asychronous Port FIC24 RS232 DTE 24 RS232 DCE 35 DTE 35 DCE 21 DTE 21 DCE DTE, DCE Front panel of 8-port FIC is shown as follows Terminal accessService DDN leased line Port Fractional FIC Connecting the Interface CableInterface Attributes Port Channelized FIC E1 FIC Data is being transceived Following table describes the LEDs on the card panelsLEDs on the Card Panel 120-ohm 4E1 adapter cable Port Channelized T1/PRI FIC Internal DIP SwitchInterface cables Port Fractional T1 FIC Interface attributes of FICcards Port Channelized T1/PRI FIC panel Interface Attributes Port Channelized E3 FIC 3C13888Main functions of 1-port Channelized E3 FIC include Port Channelized E3 FIC Interface attributes Main functions of 1-port Channelized T3 FIC include Port Channelized T3 1CT3 3C13889Connect Interface Cable LED description of 1-port T3 FIC Following table describes the LEDs on the card panelPort T3 interface attributes CT3 Sonet Following figure illustrates the 1-port OC-3 ATM SM panelPort OC ATM Attribute Port OC-3 ATM SML OC-3/SDH Following figure illustrates the 1-port OC-3 ATM SML panel Port Adsl overPots FIC 3C13872 LED description of the ATM cards FIC-1ADSL Port Adsl FIC interface attributesAttribute Port Adsl FIC LED description 2-port Adsl FIC Pstnm Flexible Interface Cards Obtaining Support for Your Product Support and Repair Contact UsTelephone Technical Latin America Telephone Technical Support and Repair US and Canada Telephone Technical Support and Repair Appendix a Obtaining Support for Your Product