Hardware Maintenance, Power Module, Removal | HP 6000 Router

5

HARDWARE MAINTENANCE

Hardware	Please review the following cautions before installation or maintenance:
Maintenance	■ On a mounting screw of 3Com 6000 series router chassis, there is an

	anti-dismantle seal of 3Com Corporation. The seal must be kept intact
	before the support agent performs maintenance on the switch.
	■ Remember to wear ESD-preventive wrist strap.

Power Module	6000 Series Routers support 1+1 redundant power system. The power modules
Removal and	are hot-swappable.
Installation

Remove a Power

Module

1Turn off power switch.

2Remove the power cord connected to the power module to be removed and loosen the two captive screws in the top panel of the module.

3Hold the handle of the module and gently pull the module out along the guides.

Figure 1 Power Module Removal

Install a Power Module

1Hold the handle of the power module panel, slowly push the module into the chassis along the guides until it touches the rear power panel inside the power slot of the chassis.

2Fasten the two captive screws in the power module panel.

Image 49

HP 6000 Router manual Hardware Maintenance, Power Module, Removal

Contents

Router 6000 Family Installation Guide Campus Drive 3Com CorporationMarlborough, MA 01752-3064 Contents Register Your Product to Gain Service Benefits Troubleshooting Application Software Upgrade Conventions About this GuideCommunication protocols that are used to interconnect WANs List conventions that are used throughout this guide Documentation RelatedRouter Use the display user-interface Introducing the Router Family Main features of 6000 RoutersIntroduction Abundant fault isolation methods Structure Router ModelComponents Front Panel Rear Panel of the 3Com Router Rear Panel Front Panel Rear Panel of the 3Com Router System Description of 6040 System description6040 6080 Sdram Introduction to Provides the hardware reset button, ResetGeneral Modules 6000 Routers modules include RPU, PSU PWR, FAN, and FICs Console interface attributes Interface Console interfaceLED and button Description Attribute Description Ethernet interface AUX interfaceAUX interface attributes MDI LED LEDs Front Panel of AC Power Module PWR LED description Fan Location Temperature/Humidity requirements in the equipment room Installing the RouterLimitation on dust content in equipment room General Site Even the entire Router Check Router Accessories Safety Recommendations3Com 6000 Routers and accessorie Name Quantity SET Installation Tools Meters Equipment 6000 Router dimensions InstallationModel Dimensions mm Various FICs Installing Modules AC power input range 100 to 240V, 50/60Hz AC Connect AC Power Cord AC power supplyCable-retention clip Power switch AC input Recommended AC power socket Connect console cable Console cable AUX cable Console failure, AUX can function as a console interface Installing the Router Configuration Configuring the RouterEstablishing Environment Configuring the Router Establishing Configuration Environment Configuring the Router Startup Process Self-test on Sdram Select booting device and download applicationsDisplay system information Following information displays on the screen Procedure Router Configuration FundamentalsDecompress Application Initialize the system Snmp Management Performs the local configuration through CON port Slot 5 Slot 7Slot 8 Slot Interface numbering rule Slot Software Maintenance Overview Software MaintenanceBoot Menu Upgrading Boot main system LargeBootrom through serial port Boot Sub-menuStarting Boot main system Modifying serial port parameters Starting application program from Flash Starting host program in default mode Entering serial port sub-menu Entering Ethernet port sub-menu Available Boot Device wancom Displaying available boot files in the Flash Then the system enters boot file control menuModifying Flash description area Setting the backup boot file Setting the main boot fileAvailable boot files Returning to Boot main menu Ignoring system configuration Upgrading Program Files Using Xmodem ProtocolRebooting the system Program Xmodem File Setting Parameters Upgrading Building up upgrade environmentApplication Program Via Ethernet Port Configuring the Router Software Maintenance Power Module Hardware MaintenanceHardware Removal Fan Removal Install a FanRight side inside the integrated chassis Remove a Fan Install an RPU RPU Removal InstallationRemove an RPU Hardware Maintenance Troubleshooting Power System TroubleshootingTroubleshooting Configuration System Troubleshooting Troubleshooting Application Software UpgradeUpgrade device of 6000 Router Displays the following prompt Troubleshooting Application Software Upgrade Troubleshooting FIC Categories Flexible Interface CardsFollowing are the FICs available for 6000 Series Routers 3C13861 Port 10/100 FIC Ethernet Cable Make Ethernet cable Port 100 FX MM FIC 1-port 100BASE-F SM FIC interface attributes SC optical fiber connector FIC 3C13863 Port Enhanced SerialFIC 3C13864 24 RS232 DTE 24 RS232 DCE 35 DTE 35 DCE 21 DTE 21 DCE Port FICAttribute Description Synchronous Asychronous DTE, DCE Service Terminal accessFront panel of 8-port FIC is shown as follows DDN leased line Interface Attributes Port Channelized FIC Connecting the Interface CablePort Fractional FIC E1 FIC LEDs on the Card Panel Following table describes the LEDs on the card panelsData is being transceived 120-ohm 4E1 adapter cable Interface cables Internal DIP SwitchPort Channelized T1/PRI FIC Port Fractional T1 FIC Port Channelized T1/PRI FIC panel Interface attributes of FICcards Main functions of 1-port Channelized E3 FIC include Port Channelized E3 FIC 3C13888Interface Attributes Port Channelized E3 FIC Interface attributes Connect Interface Cable Port Channelized T3 1CT3 3C13889Main functions of 1-port Channelized T3 FIC include Port T3 interface attributes Following table describes the LEDs on the card panelLED description of 1-port T3 FIC CT3 Port OC ATM Attribute Port OC-3 ATM SML Following figure illustrates the 1-port OC-3 ATM SM panelSonet OC-3/SDH Pots FIC 3C13872 Port Adsl overFollowing figure illustrates the 1-port OC-3 ATM SML panel LED description of the ATM cards Attribute Port Adsl FIC Port Adsl FIC interface attributesFIC-1ADSL Pstnm LED description 2-port Adsl FIC Flexible Interface Cards Obtaining Support for Your Product Telephone Technical Contact UsSupport and Repair US and Canada Telephone Technical Support and Repair Latin America Telephone Technical Support and Repair Appendix a Obtaining Support for Your Product