Installing a Scsi Device in a Scsi Device Shelf | HP D3604-90004

3 Installing Hardware Accessories

Installing a SCSI Device in a SCSI Device Shelf

Almost any Fast SCSI-2 single-ended 3.5-inch or 5.25-inch device, such as a digital audio tape (DAT), CD-ROM or SCSI hard disk drive, can be installed in a SCSI device shelf. The details for configuring the device, such as jumper settings, are supplied by the manufacturer of the device. Internal cabling configurations are described in the “Cabling Configurations” section of this manual. This section describes the basic process of installing a SCSI device in a SCSI device shelf. A SCSI hard disk drive is used as an example.

Use only the cables supplied by HP. The storage system includes an actively terminated SCSI cable for your SCSI tray devices. Fast SCSI-2 (up to 10 MB/second synchronous transfer) devices require an actively terminated SCSI cable.

NOTE To use SCSI mass storage devices, you need to obtain trays to install them in the storage system. Contact your HP dealer for obtaining these trays: 5.25-inch tray (HP D2199A), 3.5-inch tray (D2198A).

For installation of a third-party, non-HP device in a SCSI device shelf, consult the HP BBS (408-553-3500) for recommended supplies and instructions.

The following example demonstrates the procedure for installing a SCSI hard disk drive:

1.Verify that the device is not terminated because the internal SCSI cable includes a built-in terminator. If you are installing a SCSI device that uses a built-in terminator, remove the terminator from the device before proceeding with the installation. The HP accessory devices available for your storage system are shipped with the terminators disabled.

2.Power down the unit. (Since all the data stored on all the drives in the storage system is inaccessible while the system is powered down, consider informing all users before powering down the storage system.)

3.Open the door of the storage system as described in the section “Opening the Door.”

4.Position the first device closest to the SCSI cable terminator located at the end of the SCSI cable.

5.Remove the screws that secure the filler panel to the disk shelf. (Do not attempt to pry the plastic cover off the storage system.)

29

E nglish

Image 35

HP D3604-90004 manual Installing a Scsi Device in a Scsi Device Shelf

Contents

HP NetServer Storage System/6 User Guide Audience Assumptions Contents Contents Regulatory Information Page Introduction Introduction Basic Installation Unpacking the NetServer Storage System/6 Contents of the NetServer Storage System/6 Package Front View of the Storage System Identifying Parts of the NetServer Storage System/6 Nglish Scsi Self-Test Reset SwitchPower Supply Reset General Operating Instructions Continuous Operation Power Cycling Placement Temperature Control Spin Up Using an Uninterruptible Power SupplyHot-Swap Disk Module Care and Relocation Cabling Storage Devices and Setting Scsi Addresses Opening the Door Removing the Bezel and Opening the Door Storage System Switch Location Setting Scsi Addresses Settings Switch Functions Lower Cage Cabling ConfigurationsExternal Cabling Upper Cage System or Meter Cable Accessory Scsi Port Number Meter Cable Number Description Number Cabling Diagram LabelStorage System Layout Part C14 Default Cabling Configuration Non-DuplexC11 C20 Duplex Configuration Duplex Configuration C11 C14 Alternate Non-Duplex Configuration Alternate Duplex Configuration Alternate Duplex ConfigurationPage Unpacking a Hot-Swap Disk Module Installing Hardware AccessoriesInstalling Hot-Swap Storage Devices Installing Hardware Accessories Installing a New Hot-Swap Disk Module Removing a Hot-Swap Disk Module Installing the Hot-Swap Disk Module Removing the Hot-Swap Disk Module Installing a Scsi Device in a Scsi Device Shelf Installing Hardware Accessories Troubleshooting Procedures Troubleshooting Troubleshooting If The System Will Not Power On If the Scsi Devices Fail to Spin Up If the LED Readout Shows a Fan Fault FFIf the LED Readout Shows a Line Fault LF If the LED Readout Shows a Power Supply Fault PF If the Host Cannot Communicate With the Storage System If the Hot-Swap Disk Power LEDs are Flashing Troubleshooting Tools Error Messages Nglish Page System Design, Integration and Support Service and SupportService Service and Support Information and Support When You Need It HP NetServer Information Assistant CompuServe Discussion Forum and Library HP Support Assistant CD-ROM Automated Fax World Wide Web and Internet FTPBulletin Board System Telephone Support HP NetServer Support News Obtaining HP Repair and Telephone Support Ordering System Documentation Ordering HP Cables, Drive Trays and Manuals North America and Asia Ordering HP Cables, Drive Trays and Technical Publications Joining CompuServe Contacting HP Regional Headquarters CompuServe CompuServe Europe Page Limitation of Warranty Warranty and Software LicenseNetServer Storage System/6 On-Site Limited Warranty Three Year On-Site Limited Hardware Warranty Limitation of Liability and Remedies Warranty and Software LicenseObtaining Warranty Service Nglish Customer Responsibilities Removable Media if supplied Software Product Limited WarrantyObtaining Return Warranty Service Ninety-Day Limited Software Warranty Warranty and Software License Notice of Warranty Claims Environment SpecificationsWeight and Dimensions Power Supply SpecificationsPage Class B Product Statement Regulatory Information Regulatory Information Country Notices Declaration of Conformity Regulatory Information Póliza de Garantía Mexico Hardware Warranty Statement Notas Index Bios Index Nglish