Function display, QTRANSMIT Indicator

1 PANEL DESCRIPTION

■Function display

q	w	e	r	t	y	u
						i
						o
!7						!0
						!0
!6
	!5	!4	!3	!2		!1

qTRANSMIT INDICATOR

➥Appears while transmitting. (p. 17)

➥Blinks while transmitting with the one-touch PTT func- tion. (p. 18)

wDUPLEX INDICATORS (p. 20)

“DUP” appears when plus duplex, “DUP –” appears when minus duplex (repeater) operation is selected.

eTONE INDICATORS

➥“T” appears while the subaudible tone encoder is in use. (p. 20)

➥“T SQL” appears while the tone squelch function is in use. (p. 52)

➥“DTCS” appears while the DTCS squelch function is in use. (p. 52)

➥“S” appears with the “T SQL” or “DTCS” indicator while the pocket beep function (with CTCSS or DTCS) is in use. (p. 52)

Page 18

Image 18

Icom IC-208H instruction manual Function display, QTRANSMIT Indicator, WDUPLEX Indicators p, ETONE Indicators

Contents

I208H Equipment damage may occur Word Definition RwarningMay occur Personal injury, ﬁre or electric shock Precaution Operate this device under FCC regulations Supplied Accessories Dtmf Memory Encoder Installation Installation methodsQuick Reference Guide Using the mounting bracket Drill 4 holes where the mounting bracket is to be installedLocation Connect the supplied microphone as illustrated below Microphone connectionSeparation cable connection Detach the controller as below Optional MB-58 installation Drill 2 or 4 holes where the bracket is to be installedWhen using the optional MB-65 Connecting to a DC Power Source Battery connectionDC power supply connection Connecting to a DC Power Supply Antenna uses a PL-259 connector Antenna installationAntenna connector Antenna location Push Band to select the desired frequency band Your ﬁrst contactIC-208H has 2 m and 70 cm transmittable bands You can select the desired frequency band from the HM-133 Tune the frequency Setting duplex Repeater operation Programming memory channels Push Func then CLR AMWPush and hold S.MWMW for 1 sec. to program Panel Description Front panel- controller 0MEMORY/CALLPRIORITY Switch M/CALLPRIO 2BAND Switch Band4CONTROLLER Release Latch ETONE Indicators QTRANSMIT IndicatorWDUPLEX Indicators p Function display 6OUTPUT Power Indicators 2MEMORY Channel Number Indicators5S/RF Indicators 7BUSY Indicator Rear Panel Antenna Information Data Jack PIN Assignment 0BAND Switch Band 1MEMORY/CALL Switch MR/CALLMicrophone HM-133 Microphone keypad Holding Ation is performed Cancels frequency entryCancels the scan or priority watch Ming Ing the a to D, # and Mkeys Optional Microphones HM-118N/TN/TAN Preparation Setting a FrequencyDTurning power ON/OFF Dvfo and memory modes Using the tuning dial Using the Y/Z keysUsing the keypad Tuning step selection Push Setlock to enter set mode Frequency lock Switch the microphone keypad lock functionLock functions DMicrophone keypad lock Monitor function Basic OperationReceiving SQL Y DMUTE/ SQL Z #16KEY-L, respectively Push PWR to exit initial set mode Squelch attenuator Selecting output power RF Indicator Power OutputTransmitting One-touch PTT function Audio mute functionPush PTT to transmit and push again to re- ceive Repeater operation ﬂow chart Repeater OperationGeneral Accessing a repeater Push and hold PTT to transmitRelease PTT to receive Set the receive frequency repeater output fre Push Simp 9TSQL to return to simplex opera- tion Subaudible tones Subaudible tonesSubaudible tone frequency list Dtmf tones Hz tone Offset frequency Push Band to select the desired frequency SET bandPush Y or Z to set the desired offset Setting the auto repeater function ON/OFF Frequency range and offset directionFrequency range Duplex direction Memory Operation General descriptionMemory channel selection Programming a memory channel Rotate Dial to select the memory channel to be pro- grammedPush S.MWMW for 1 sec. to program Programming a memory channel via the microphone Copying memory contents Select the memory/call channel to be transferred Example Transferring memory channel 30 contents to channelMemory/callmemory/call Rotate Dial to select the target memory channel Rotate the tuning dial to select the desired character Programming channel names Push Then push To select the channel. Push DTo indicate the channel name Push SET BD-OFF or ENT CT-OFF until ANM appear Memory clearing Rotate Dial to select the memory channel to be clearedPush S.MWMW momentarily, then push S.MWMW again for 1 sec Memory bank selection Rotate Dial to select the contents in the bankPush Y/Z to select the desired contents in the bank Rotate Dial to select the desired bank, a to J Memory bank setting Push MR/CALL then select the desired memOry channel via Y/Z or keypad Transferring bank contents Call Channel Operation Call channel selectionCall channel transferring Programming a call channel Scan Operation Scan types Scan start/stop Push VFO/LOCK to select VFO mode forMemory mode for memory scan Preparation Scan edges programming Example Programming 145.300 MHz into scan edges 1A Programming scan edges via microphone Skip channel setting Push Monidtmf to exit set modeSelect a memory channel Rotate Dial to set the desired timer Scan resume condition Priority Watch Priority watch typesOrity watch starts Priority watch operation Push M/CALLPRIO for 1 sec. to stop the watchPush MR/CALL, then push Scan 2 to start the memory scan Push Monidtmf for 1 sec. to turn the Dtmf encoder on Dtmf Memory EncoderProgramming a Dtmf code Push Monidtmf to exit Dtmf memory programming condition Push Func then LOW 6DTMF to turn Dtmf Dtmf encoder on Push VFO/LOCK to exit the programming condition Transmitting a Dtmf code Automatic transmission Dtmf memoryTransmitting a Dtmf memory directly Manual transmission Mentarily, then push the desired Dtmf keys A to FPush DTMF-S again to deactivate the Dtmf direct selection Waiting for a call from a speciﬁc station Pocket Beep and Tone SquelchPocket beep operation Lect the Dtcs polarity Calling a waiting station using pocket beep Available tone frequency list Tone/DTCS squelch operation Tone scan Push TONET-SCAN for 1 sec. to start the tone scanSelects the tone type to be scanned Set mode Other Functions Repeater tone Display dimmerDisplay color Tone squelch tone Offset frequency Tuning stepDtcs code Dtcs polarity Channel skip setting Scan resume timerMemory name setting Memory bank setting Memory bank link function Program scan skip settingBank link setting Turns weather alert function on and OFF Initial set mode Entering initial set mode Time-out timer DAuto power OFFKey-touch beep Data transmission speed Squelch delayCooling fan control Microphone sensitivity Active band Dtmf speedNarrow TX function AM/FM narrow mode Push Band or MR/CALL to select the desired Weather channel selection Turn the weather alert function OFF in set modeWeather channel operation Weather alert function UP/DN keys on a microphones Default settingMicrophone keys 1/F-2 keys on HM-133 Partial reset Cloning between transceivers Push Setlock on the master transceiver Cloning using a personal computer Cloning error Data speed Packet operationBps packet operation Connect the transceiver and a TNC as illustrated below Other Functions Bps high speed packet operation Adjusting the transmit signal output from TNC Increase the TNC output level Maintenance TroubleshootingProblem Possible Cause Solution Fuse replacement 20 aFuse Dgeneral Specifications and OptionsSpeciﬁcations Dtransmitter OPC-347/OPC-1132 DC Power Cables OptionsOPC-600/600R*, OPC-601/601R* Separation Cables Mode Arrangement Mode Arrangement Kamiminami, Hirano-ku, Osaka 547-0003 Japan

Icom IC-208H Function display, QTRANSMIT Indicator, WDUPLEX Indicators p, ETONE Indicators

Models: IC-208H

1 PANEL DESCRIPTION

■Function display

qTRANSMIT INDICATOR

wDUPLEX INDICATORS (p. 20)

eTONE INDICATORS