Push Then push To select the channel. Push | Icom IC-208H specification

MEMORY OPERATION 5

Channel names can also be programmed via the mi- crophone.

zPush [FUNC] then [CLR A(MW)] momentarily.

• “!” and memory channel number blink.

xPush [Y]/[Z] to select the memory/call channel to be as-

signed memory names.

cPush [BAND].

• Frequency readouts disappear and a cursor blinks.

nRepeat steps v and b until the desired channel names are displayed.

mPush [FUNC] then [CLR A(MW)] for 1 sec. to program the

name and exit the channel name programming condition.

5

vPush [Y]/[Z] to select the desired character.

• The selected character blinks.

bPush [SET B(D-OFF)] or [ENT C(T-OFF)] to move the cur- sor to left or right, respectively.

[EXAMPLE]: Programming “CLUB” into memory channel 1.

Push

, then push

. Push

to select the channel. Push

Push

to select the character

Push	or	to move the cursor. Repeat the
		previous
		steps.

Push , then push for 1 sec.

“Beep“

“Beep

“ Beep

“

32

Image 47

Icom IC-208H instruction manual Push Then push To select the channel. Push

Contents

I208H Personal injury, ﬁre or electric shock Word Definition RwarningMay occur Equipment damage may occur Operate this device under FCC regulations Precaution Supplied Accessories Dtmf Memory Encoder Quick Reference Guide InstallationInstallation methods Location Using the mounting bracketDrill 4 holes where the mounting bracket is to be installed Detach the controller as below Microphone connectionSeparation cable connection Connect the supplied microphone as illustrated below When using the optional MB-65 Optional MB-58 installationDrill 2 or 4 holes where the bracket is to be installed Connecting to a DC Power Supply Battery connectionDC power supply connection Connecting to a DC Power Source Antenna location Antenna installationAntenna connector Antenna uses a PL-259 connector You can select the desired frequency band from the HM-133 Your ﬁrst contactIC-208H has 2 m and 70 cm transmittable bands Push Band to select the desired frequency band Tune the frequency Repeater operation Setting duplex Push and hold S.MWMW for 1 sec. to program Programming memory channelsPush Func then CLR AMW Front panel- controller Panel Description 4CONTROLLER Release Latch 0MEMORY/CALLPRIORITY Switch M/CALLPRIO2BAND Switch Band Function display QTRANSMIT IndicatorWDUPLEX Indicators p ETONE Indicators 7BUSY Indicator 2MEMORY Channel Number Indicators5S/RF Indicators 6OUTPUT Power Indicators Antenna Information Rear Panel Data Jack PIN Assignment Microphone HM-133 0BAND Switch Band1MEMORY/CALL Switch MR/CALL Holding Microphone keypad Ing the a to D, # and Mkeys Cancels frequency entryCancels the scan or priority watch Ming Ation is performed Optional Microphones HM-118N/TN/TAN Dvfo and memory modes Setting a FrequencyDTurning power ON/OFF Preparation Using the keypad Using the tuning dialUsing the Y/Z keys Push Setlock to enter set mode Tuning step selection DMicrophone keypad lock Switch the microphone keypad lock functionLock functions Frequency lock SQL Y DMUTE/ SQL Z #16KEY-L, respectively Basic OperationReceiving Monitor function Squelch attenuator Push PWR to exit initial set mode Transmitting Selecting output powerRF Indicator Power Output Push PTT to transmit and push again to re- ceive One-touch PTT functionAudio mute function General Repeater operation ﬂow chartRepeater Operation Release PTT to receive Accessing a repeaterPush and hold PTT to transmit Push Simp 9TSQL to return to simplex opera- tion Set the receive frequency repeater output fre Subaudible tone frequency list Subaudible tonesSubaudible tones Hz tone Dtmf tones Push Y or Z to set the desired offset Offset frequencyPush Band to select the desired frequency SET band Frequency range Duplex direction Setting the auto repeater function ON/OFFFrequency range and offset direction Memory channel selection Memory OperationGeneral description Push S.MWMW for 1 sec. to program Programming a memory channelRotate Dial to select the memory channel to be pro- grammed Programming a memory channel via the microphone Copying memory contents Rotate Dial to select the target memory channel Example Transferring memory channel 30 contents to channelMemory/callmemory/call Select the memory/call channel to be transferred Programming channel names Rotate the tuning dial to select the desired character Push Then push To select the channel. Push Push SET BD-OFF or ENT CT-OFF until ANM appear DTo indicate the channel name Push S.MWMW momentarily, then push S.MWMW again for 1 sec Memory clearingRotate Dial to select the memory channel to be cleared Rotate Dial to select the desired bank, a to J Rotate Dial to select the contents in the bankPush Y/Z to select the desired contents in the bank Memory bank selection Ory channel via Y/Z or keypad Memory bank settingPush MR/CALL then select the desired mem Transferring bank contents Call channel transferring Call Channel OperationCall channel selection Programming a call channel Scan types Scan Operation Preparation Push VFO/LOCK to select VFO mode forMemory mode for memory scan Scan start/stop Example Programming 145.300 MHz into scan edges 1A Scan edges programming Programming scan edges via microphone Select a memory channel Skip channel settingPush Monidtmf to exit set mode Scan resume condition Rotate Dial to set the desired timer Ority watch starts Priority WatchPriority watch types Push MR/CALL, then push Scan 2 to start the memory scan Priority watch operationPush M/CALLPRIO for 1 sec. to stop the watch Push Monidtmf to exit Dtmf memory programming condition Dtmf Memory EncoderProgramming a Dtmf code Push Monidtmf for 1 sec. to turn the Dtmf encoder on Push VFO/LOCK to exit the programming condition Push Func then LOW 6DTMF to turn Dtmf Dtmf encoder on Transmitting a Dtmf memory directly Transmitting a Dtmf codeAutomatic transmission Dtmf memory Push DTMF-S again to deactivate the Dtmf direct selection Manual transmissionMentarily, then push the desired Dtmf keys A to F Lect the Dtcs polarity Pocket Beep and Tone SquelchPocket beep operation Waiting for a call from a speciﬁc station Available tone frequency list Calling a waiting station using pocket beep Tone/DTCS squelch operation Selects the tone type to be scanned Tone scanPush TONET-SCAN for 1 sec. to start the tone scan Other Functions Set mode Tone squelch tone Display dimmerDisplay color Repeater tone Dtcs polarity Tuning stepDtcs code Offset frequency Memory bank setting Scan resume timerMemory name setting Channel skip setting Turns weather alert function on and OFF Program scan skip settingBank link setting Memory bank link function Entering initial set mode Initial set mode Key-touch beep Time-out timerDAuto power OFF Microphone sensitivity Squelch delayCooling fan control Data transmission speed Narrow TX function Active bandDtmf speed Push Band or MR/CALL to select the desired AM/FM narrow mode Weather alert function Turn the weather alert function OFF in set modeWeather channel operation Weather channel selection 1/F-2 keys on HM-133 Default settingMicrophone keys UP/DN keys on a microphones Partial reset Push Setlock on the master transceiver Cloning between transceivers Cloning error Cloning using a personal computer Connect the transceiver and a TNC as illustrated below Packet operationBps packet operation Data speed Other Functions Bps high speed packet operation Increase the TNC output level Adjusting the transmit signal output from TNC Problem Possible Cause Solution MaintenanceTroubleshooting Fuse Fuse replacement20 a Dtransmitter Specifications and OptionsSpeciﬁcations Dgeneral OPC-600/600R*, OPC-601/601R* Separation Cables OPC-347/OPC-1132 DC Power CablesOptions Mode Arrangement Mode Arrangement Kamiminami, Hirano-ku, Osaka 547-0003 Japan