Microphone connection, Separation cable connection

QUICK REFERENCE GUIDE

DMicrophone connection

Connect the supplied microphone as illustrated below.

DSeparation cable connection

Using the supplied separation cable (3.5 m; 11.5 ft) or the op- tional separation cable (7 m; 23 ft) the controller can be sep- arated from the main unit, doubling as a remote controller.

qDetach the controller as below.

Release latch

wConnect a separation cable between the controller and main unit using the supplied screws as illustrated below.

• Controller’s rear panel

• Main unit

OPC-600/R or OPC-601/R

A ferrite core is adapted for the USA version.

CAUTION!

NEVER short the terminals of the separation connector.

The 13.8 V power line is available in the connector, so the transceiver may damage when short circuited.

NEVER short the terminals

III

Page 8

Image 8

Icom IC-208H Microphone connection, Separation cable connection, Connect the supplied microphone as illustrated below

Contents

I208H Word Definition Rwarning May occurEquipment damage may occur Personal injury, ﬁre or electric shock Precaution Operate this device under FCC regulations Supplied Accessories Dtmf Memory Encoder Quick Reference Guide InstallationInstallation methods Location Using the mounting bracketDrill 4 holes where the mounting bracket is to be installed Microphone connection Separation cable connectionConnect the supplied microphone as illustrated below Detach the controller as below When using the optional MB-65 Optional MB-58 installationDrill 2 or 4 holes where the bracket is to be installed Battery connection DC power supply connectionConnecting to a DC Power Source Connecting to a DC Power Supply Antenna installation Antenna connectorAntenna uses a PL-259 connector Antenna location Your ﬁrst contact IC-208H has 2 m and 70 cm transmittable bandsPush Band to select the desired frequency band You can select the desired frequency band from the HM-133 Tune the frequency Setting duplex Repeater operation Push and hold S.MWMW for 1 sec. to program Programming memory channelsPush Func then CLR AMW Panel Description Front panel- controller 4CONTROLLER Release Latch 0MEMORY/CALLPRIORITY Switch M/CALLPRIO2BAND Switch Band QTRANSMIT Indicator WDUPLEX Indicators pETONE Indicators Function display 2MEMORY Channel Number Indicators 5S/RF Indicators6OUTPUT Power Indicators 7BUSY Indicator Rear Panel Antenna Information Data Jack PIN Assignment Microphone HM-133 0BAND Switch Band1MEMORY/CALL Switch MR/CALL Microphone keypad Holding Cancels frequency entry Cancels the scan or priority watch MingAtion is performed Ing the a to D, # and Mkeys Optional Microphones HM-118N/TN/TAN Setting a Frequency DTurning power ON/OFFPreparation Dvfo and memory modes Using the keypad Using the tuning dialUsing the Y/Z keys Tuning step selection Push Setlock to enter set mode Switch the microphone keypad lock function Lock functionsFrequency lock DMicrophone keypad lock Basic Operation ReceivingMonitor function SQL Y DMUTE/ SQL Z #16KEY-L, respectively Push PWR to exit initial set mode Squelch attenuator Transmitting Selecting output powerRF Indicator Power Output Push PTT to transmit and push again to re- ceive One-touch PTT functionAudio mute function General Repeater operation ﬂow chartRepeater Operation Release PTT to receive Accessing a repeaterPush and hold PTT to transmit Set the receive frequency repeater output fre Push Simp 9TSQL to return to simplex opera- tion Subaudible tone frequency list Subaudible tonesSubaudible tones Dtmf tones Hz tone Push Y or Z to set the desired offset Offset frequencyPush Band to select the desired frequency SET band Frequency range Duplex direction Setting the auto repeater function ON/OFFFrequency range and offset direction Memory channel selection Memory OperationGeneral description Push S.MWMW for 1 sec. to program Programming a memory channelRotate Dial to select the memory channel to be pro- grammed Programming a memory channel via the microphone Copying memory contents Example Transferring memory channel 30 contents to channel Memory/callmemory/callSelect the memory/call channel to be transferred Rotate Dial to select the target memory channel Rotate the tuning dial to select the desired character Programming channel names Push Then push To select the channel. Push DTo indicate the channel name Push SET BD-OFF or ENT CT-OFF until ANM appear Push S.MWMW momentarily, then push S.MWMW again for 1 sec Memory clearingRotate Dial to select the memory channel to be cleared Rotate Dial to select the contents in the bank Push Y/Z to select the desired contents in the bankMemory bank selection Rotate Dial to select the desired bank, a to J Ory channel via Y/Z or keypad Memory bank settingPush MR/CALL then select the desired mem Transferring bank contents Call channel transferring Call Channel OperationCall channel selection Programming a call channel Scan Operation Scan types Push VFO/LOCK to select VFO mode for Memory mode for memory scanScan start/stop Preparation Scan edges programming Example Programming 145.300 MHz into scan edges 1A Programming scan edges via microphone Select a memory channel Skip channel settingPush Monidtmf to exit set mode Rotate Dial to set the desired timer Scan resume condition Ority watch starts Priority WatchPriority watch types Push MR/CALL, then push Scan 2 to start the memory scan Priority watch operationPush M/CALLPRIO for 1 sec. to stop the watch Dtmf Memory Encoder Programming a Dtmf codePush Monidtmf for 1 sec. to turn the Dtmf encoder on Push Monidtmf to exit Dtmf memory programming condition Push Func then LOW 6DTMF to turn Dtmf Dtmf encoder on Push VFO/LOCK to exit the programming condition Transmitting a Dtmf memory directly Transmitting a Dtmf codeAutomatic transmission Dtmf memory Push DTMF-S again to deactivate the Dtmf direct selection Manual transmissionMentarily, then push the desired Dtmf keys A to F Pocket Beep and Tone Squelch Pocket beep operationWaiting for a call from a speciﬁc station Lect the Dtcs polarity Calling a waiting station using pocket beep Available tone frequency list Tone/DTCS squelch operation Selects the tone type to be scanned Tone scanPush TONET-SCAN for 1 sec. to start the tone scan Set mode Other Functions Display dimmer Display colorRepeater tone Tone squelch tone Tuning step Dtcs codeOffset frequency Dtcs polarity Scan resume timer Memory name settingChannel skip setting Memory bank setting Program scan skip setting Bank link settingMemory bank link function Turns weather alert function on and OFF Initial set mode Entering initial set mode Key-touch beep Time-out timerDAuto power OFF Squelch delay Cooling fan controlData transmission speed Microphone sensitivity Narrow TX function Active bandDtmf speed AM/FM narrow mode Push Band or MR/CALL to select the desired Turn the weather alert function OFF in set mode Weather channel operationWeather channel selection Weather alert function Default setting Microphone keysUP/DN keys on a microphones 1/F-2 keys on HM-133 Partial reset Cloning between transceivers Push Setlock on the master transceiver Cloning using a personal computer Cloning error Packet operation Bps packet operationData speed Connect the transceiver and a TNC as illustrated below Other Functions Bps high speed packet operation Adjusting the transmit signal output from TNC Increase the TNC output level Problem Possible Cause Solution MaintenanceTroubleshooting Fuse Fuse replacement20 a Specifications and Options SpeciﬁcationsDgeneral Dtransmitter OPC-600/600R*, OPC-601/601R* Separation Cables OPC-347/OPC-1132 DC Power CablesOptions Mode Arrangement Mode Arrangement Kamiminami, Hirano-ku, Osaka 547-0003 Japan

Icom IC-208H Microphone connection, Separation cable connection, Detach the controller as below

Models: IC-208H

DMicrophone connection

Connect the supplied microphone as illustrated below.

DSeparation cable connection

qDetach the controller as below.