SEAT FRAME

PROCEDURE 6

 

 

3.Cut tie wraps and disconnect joystick from controller.

4.Turn the lever on the adjustment lock to release the adjustment lock from the joystick mounting tube.

5.Remove the joystick from the wheelchair.

6.Perform one (1) of the following:

4.ReinstallthecomponentspreviouslyremovedinSTEP 1.PerformtheinstructionsoutlinedinPREPARATIONS FORREMOVING/INSTALLINGSEATFRAME(STAN- DARD FRAME, ADJUSTABLE FRAME,AND CAP- TAINS VAN SEAT) in this procedure of the manual.

S E

A. STANDARD OR ADJUSTABLE SEAT FRAMES - Remove the flip-back armrests from thewheelchair.RefertoINSTALLING/REMOVING FLIP BACK ARMRESTS in PROCEDURE 4 of the owner’s manual, 1081227.

B. CAPTAINS VAN SEAT - Remove the mounting

screw that secures the armrest to the van seat

frame. Repeat for opposite side.

7. For standard and adjustable seat frames, remove the

seat pan (including seat positioning straps). Refer to

REMOVING/INSTALLINGSEATPANinthisprocedure

REMOVING/INSTALLING

STANDARD SEAT FRAME

SUBASSEMBLY (FIGURE 2)

NOTE: Perform steps required from starting procedure.

Removing

1.Remove the four (4) mounting screws, locknuts and spacers, if applicable, that secure the standard seat frame subassembly to the seat mounting plates.

2.Remove the existing standard seat frame.

A

T

F

R A M E

 

of the manual.

8.

Disconnectbatteryandleft/rightmotorconnectorsfrom

 

the controller. Refer to REPLACING WIRING HAR-

 

NESS in PROCEDURE 10 of this manual.

9.

Remove tie-wraps that secures the wiring harness to

 

the seat frame and the charger cable from its mount-

 

ingbracket.RefertoREPLACINGWIRINGHARNESS

 

in PROCEDURE 10 of this manual.

10.

For standard and adjustable seat frames, remove the

 

back upholstery (including back canes and spreader

 

bar, if applicable). Refer to REPLACING BACK UP-

 

HOLSTERY in PROCEDURE 5 of the manual.

11.

Refer back to the starting procedure to complete the

 

desired change.

REPLACING EXACT SAME SIZE STANDARD SEAT FRAME

1.

Perform the instructions outlined in PREPARATIONS

 

FORREMOVING/INSTALLINGSEATFRAME(STAN-

 

DARD FRAME, ADJUSTABLE FRAME, AND CAP-

 

TAINS VAN SEAT) in this procedure of the manual.

2.

Remove the existing standard seat frame subassem-

 

bly and install the NEW standard frame. Refer to RE-

 

MOVING/INSTALLING STANDARD SEAT FRAME

 

SUBASSEMBLY in this procedure of the manual.

3.

FOR 12-15-INCH SEAT DEPTHS ONLY: Remove

Mounting Screws

(Torque to 156-

inch pounds)

Standard

Seat

Assembly

Spacer

(16-inch Wide

Only)

Locknuts

Mounting Screws

(Torque to 156-

inch pounds)

Spacer

(16-inch

Wide Only)

Seat

Mounting

Plate

Base Frame

the CJ back brackets from the existing standard seat

frame and install onto the NEW standard seat frame.

RefertoREMOVING/INSTALLINGCJBACKBRACK-

ETS FROM SEAT FRAME in this procedure of the

manual.

NOTE: For 16-inch wide seat frames, there will be spac- erspositionedbetweentheseatframeandtheseatmount- ing plates.

FIGURE 2 - REMOVING/INSTALLING STANDARD

SEAT FRAME SUB-ASSEMBLY

23

Page 23
Image 23
Invacare Ranger X, Arrow REMOVING/INSTALLING Standard Seat Frame Subassembly Figure, Seat Frame Procedure, Removing