Invacare Ranger X, Arrow Replacing Battery Charger Bracket and T-NUT, RWD and MWD Models Figure

BASE FRAME PROCEDURE 7

12.Reinstall the seat mount plates. Refer to REPLACING SEAT MOUNTING PLATES in this procedure of the manual.

13.Adjust seat mounting plates to desired angle. Refer to

MOUNTING PLATE - SEAT ANGLE ADJUSTMENT ANDINSTALLATIONORIENTATIONinPROCEDURE 6 of this manual.

14.Reverse STEP 2A, 2B or 2C.

15.Perform the instructions outlined in PREPARATIONS FORREMOVING/INSTALLINGSEATFRAME(STAN- DARD FRAME, ADJUSTABLE FRAME, AND CAP- TAINS VAN SEAT) in PROCEDURE 6 of this manual.

REPLACING BATTERY CHARGER BRACKET AND T-NUT

NOTE: There is no T-nut on the FWD models.

RWD and MWD Models (FIGURE 4)

1.Perform the instructions outlined in PREPARATIONS FOR REMOVING/INSTALLING THE SEAT FRAME (STANDARD FRAME, ADJUSTABLE FRAME, AND CAPTAINS VAN SEAT) in PROCEDURE 6 of this manual.

2.Perform one (1) of the following:

A.Remove standard seat frame subassembly. Refer to REMOVING/INSTALLING STANDARD SEAT FRAME SUBASSEMBLY in PROCEDURE 6 of this manual.

B.Remove adjustable seat frame subassembly. Re- fer to INSTALLING/REMOVING ADJUSTABLE SEAT FRAME ASSEMBLY AND OR COMPO- NENT REPLACEMENT in PROCEDURE 6 of this manual.

C.Remove captains van seat. Refer toINSTALLING/ REMOVINGCAPTAINSVANSEATASSEMBLYin PROCEDURE 6 of this manual.

3.Remove the seat support brackets. Refer to RE- PLACING SEAT SUPPORT BRACKETS in this procedure of this manual.

4.Remove the two (2) mounting screws that secure the battery charger connector to the mount bracket.

5.Removebatterychargerconnectorfrommountbracket.

6.Removethemountingscrewwhichsecuresthebattery charger mount bracket to the T-nut located in the chan- nel of the base frame.

7.Replace battery charger mount bracket and secure to base frame with existing mounting screw.

NOTE: To replace the Battery Charger Bracket T-Nut, per- form STEPS 3-13 in REPLACING SEAT SUPPORT BRACKET T-NUTS in this procedure of the manual.

8.Secure the battery charger connector to the mount bracket with the EXISTING two (2) mounting screws. Tightensecurely.

9.Reverse STEP 2A, 2B or 2C.

10.Perform the instructions outlined in PREPARATIONS FORREMOVING/INSTALLINGSEATFRAME(STAN- DARD FRAME, ADJUSTABLE FRAME, AND CAP- TAINS VAN SEAT) in PROCEDURE 6 of this manual.

	Mounting Screw
Battery	Battery
	Charger
Charger
	Connector
Mount
Bracket
	T-nut

Base

Frame

FIGURE 4 - RWD AND MWD MODELS

Arrow FWD Model (FIGURE 5)

1.Perform one (1) of the following:

A.For LOW MOUNT BRACKETS, perform STEPS 1-11.

B.For MEDIUM/HIGH MOUNT BRACKETS per- form STEPS 4-9 ONLY.

2.Perform the instructions outlined in PREPARATIONS FOR REMOVING/INSTALLING THE SEAT FRAME (STANDARD FRAME, ADJUSTABLE FRAME, AND CAPTAINS VAN SEAT) in PROCEDURE 6 of this manual.

3.Perform one (1) of the following:

A.Remove standard seat frame subassembly. Refer to REMOVING/INSTALLING STANDARD SEAT FRAME SUBASSEMBLY in PROCEDURE 6 of this manual.

B.Remove adjustable seat frame subassembly. Re- fer to INSTALLING/REMOVING ADJUSTABLE SEAT FRAME ASSEMBLY AND OR COMPO- NENT REPLACEMENT in PROCEDURE 6 of this manual.

C.Remove captains van seat. Refer toINSTALLING/ REMOVINGCAPTAINSVANSEATASSEMBLYin PROCEDURE 6 of this manual.

4.Remove the front shroud. Refer to REMOVING/IN- STALLING FRONT SHROUD in PROCEDURE 17 of the manual.

B A S E

F

R A M E

35