Speciﬁcations, 4 Technical Information | J. T. Eaton LCX9000

Speciﬁcations

LCX9000 Liquid-Cooled Drives User Manual

January 2007

Speciﬁcations

Table 1-4: Technical Information

Description	Speciﬁcation

Mains Connection

Input voltage Uin	400 – 500V AC; 525 – 690V AC; (-10% – 10%)
	465 – 800V DC; 640 – 1100V DC; (-0% – 0%)
Input frequency	45 – 66 Hz

Connection to mains	Once per minute or less

Motor Connection

Output voltage	0 – Uin
Continuous output current	Rated current at nominal inﬂow cooling water temperature
	according to dimensioning charts

Output frequency	0 – 320 Hz (standard); 7200 Hz (Special software)

Frequency resolution	Application dependent

Control Characteristics

Control method	Frequency control U/f
	Open Loop Sensorless Vector Control
	Closed Loop Vector Control

Switching frequency	480V:	Up to and including 61 Amp Size:
(see parameter 2.6.9)		1 – 16 kHz; Factory default 10 kHz
		From 72 Amp Size:
		1 – 12 kHz; Factory default 3.6 kHz
	575V:	1 – 6 kHz; Factory default 1.5 kHz
	Note: Derating required if higher switching frequency than the
	default is used!

Frequency reference
Analog input	Resolution 0.1% (10-bit), accuracy ±1%
Panel reference	Resolution 0.01 Hz

Field weakening point	8 – 320 Hz

Acceleration time	.1 – 3000 sec

Deceleration time	.1 – 3000 sec

Braking torque	DC brake: 30% * TN (without brake option)
Ambient Conditions

Ambient operating temperature	14°F (-10°C) (no frost) to +122°F (+50°C) (at Ith)
	122 – 158°F (50 to 70°C) derating required, see Pages 2-13and 2-19
Storage temperature	-40 to +158°F (-40 to +70°C); No liquid in heatsink under 32°F (0ºC)

Relative humidity	5 to 96% RH, non-condensing, no dripping water

Air quality:
chemical vapors	IEC 721-3-3, unit in operation, class 3C2
mechanical particles	IEC 721-3-3, unit in operation, class 3S2 (no conductive dust allowed)
	No corrosive gases
Altitude	100% load capacity (no derating) up to 1,000m; above 1,000m
	derating of 1% per each 100m required

Vibration	5 – 150 Hz
EN50178/EN60068-2-6	Displacement amplitude .25 mm (peak) at 3 – 31 Hz
	Max acceleration amplitude 1 G at 31 – 150 Hz

Shock	UPS Drop Test (for applicable UPS weights)
EN50178, EN60068-2-27	Storage and shipping: max 15G, 11 mS (in package)

Enclosure class	IP00/Open Frame standard in entire kW/hp range

MN04005001E

For more information visit: www.EatonElectrical.com

1-9

Image 21

J. T. Eaton LCX9000 user manual Speciﬁcations, 4 Technical Information

Contents

LCX9000 Liquid-Cooled Drives User Manual January Supersedes SeptemberMN04005001E Page Important Notice - Please Read CHAPTER 4 - CONTROL WIRING AND INTERNAL CONNECTIONS Table ofContents List of Figures List of Figures Continued List of Tables Table 5-13 Resettable Counters List of Tables ContinuedTable A-1 Fault Codes Table 5-11 System Menu Functions Safety Deﬁnitions and SymbolsHazardous High Voltage Warnings Warnings, Cautions and Notices Cautions Motor and Equipment Safety Grounding and Ground Fault Protection Receiving and Inspection Chapter 1 - Overview L C X 0 1 6 A 0 - 4 A 2 B Maintenance Technical DataStorage and Shipping LCX9000 Liquid-Cooled Drives User Manual Figure 1-1 Liquid-Cooled Drive Principal Block Diagram Drives Power RatingsPage Page Table 1-4 Technical Information Speciﬁcations 1-10 Table 1-4 Technical Information Continued Chapter 2 - Installation MountingLifting the Drive Table 2-1 One-Module Drive Dimensions Mounting Base Included Liquid-Cooled DimensionsDrives Consisting of One Module Figure 2-2 LCX9000 Liquid-Cooled Drive, CH3 Figure 2-4 LCX9000 Liquid-Cooled Drive, CH5 Figure 2-3 LCX9000 Liquid-Cooled Drive, CH4Bottom View Top View Figure 2-6 LCX9000 Liquid-Cooled Drive, CH72 Figure 2-5 LCX9000 Liquid-Cooled Drive, CH61 Table 2-2 Several Module Drive Dimensions Mounting Bracket Included Drives Consisting of Several ModulesFigure 2-7 Drive Mounted Inside Mounting Bracket Figure 2-8 LCX9000 Liquid-Cooled Drive with Mounting Bracket, CH63 Bottom Figure 2-9 LCX9000 Liquid-Cooled Drive, CH74, IP006-Pulse Supply 12-Pulse Supply Drinking Water Speciﬁcation CoolingTable 2-3 Drinking Water Chemical Speciﬁcation Table 2-4 Drinking Water Quality Recommendations - Maximum Values Table 2-6 Process Water Speciﬁcation Table 2-5 Drinking Water Quality Recommendations - Desired Values Figure 2-10 Example of Cooling System ExchangerHeat Table 2-7 Information About Cooling Agent and Its Circulation Figure 2-11 Example PI-Diagram of Cooling System and Connections Table 2-9 Coolant Volumes and Temperatures Figure 2-12 Safe Operating Conditions in Relation to Condensation Condensation Cooling System Connections Table 2-10 Liquid Connector Types All Pressure Values at Nominal FlowFigure 2-13 Aluminum Hose Adapters Figure 2-14 External Thread of Hose Pressure Losses Table 2-11 Pressure Losses - CH6x Figure 2-15 Pressure Loss - CH6xOutﬂow Hoses and Figure 2-16 Pressure Loss - CH7x Table 2-12 Pressure Losses - CH7xThe following main line hose materials are acceptable plastic PVC rubber EPDM only aluminium other stainless and acid-proof materials About Flow Switch Installation Installation of Flow SwitchFigure 2-17 Flow Switch Hose Connection, Fast Connector Electrical Fast Connector Lock Screw, Cable Seal and Clamp External Cooling Fan for CH4 Figure 2-18 Direction of Coolant Circulation Drive Derating Input Chokes Table 2-16 Input Choke Dimensioning, 6-Pulse Supply Figure 2-19 Example of Input Chokes for Liquid-Cooled Sizes Up to 62A Installation of Input ChokeFigure 2-20 Example of Input Chokes for Liquid-Cooled Sizes 87 - 145A and 590A January Table 2-17 Choke Dimensions Sizes 23 - 145A and 590A Table 2-18 Choke Dimensions Sizes 261 - 1150A LCX9000 Liquid-Cooled Drives User Manual Power Connections Chapter 3 - Power WiringMains Cable Motor Cable Table 3-1 Cable Types Required to Meet Standards Cable DataTable 3-2 Cable Sizes 400 Units with 6-pulse supply Table 3-2 Cable Sizes 400 - 500V ContinuedUnits with 12-pulse supply Three grounding terminals per mounting plate, see Page Table 3-3 Cable Sizes 525 Table 3-4 Tightening Torques of BoltsSee the tightening torques of bolts in Table Table 3-5 Fuse Sizes for LCX9000 Liquid-Cooled 500V Drives Fuse Sizes, Drives Fuse information Table 3-6 Fuse Sizes for LCX9000 Liquid-Cooled 690V Drives Cable Installation Instructions The maximum length of the motor cables is 984 feet 300m4. If cable insulation checks are needed, see Page Figure 3-1 Maximum Terminal Stresses Figure 3-2 Installation Space Installation Space Grounding of Power Unit Cable Installation and the UL StandardsFigure 3-3 Grounding Terminal on Mounting Plate Cable and Motor Insulation Checks 3-12 Figure 4-1 Control Board Chapter 4 - Control Wiring and Internal Connections Figure 4-3 Drives Connected in Parallel Figure 4-2 Basic and Option Board Connections of the Control Board Figure 4-4 Connection of Control Board Cable from the Power Board Control Board Power-UpSee Figures 4-4 and WRONG Terminal J1 Upper Control Connections Figure 4-5 Connection of Control Board Cable from the Power BoardCORRECT Terminal J2 Lower Figure 4-6 I/O Terminals of the Two Basic Boards Figure 4-8 General Wiring Diagram of the Basic Relay Board OPT-A2 Figure 4-7 General Wiring Diagram of the Basic I/O Board OPT-A9 Control Cables Galvanic Isolation BarriersFigure 4-9 Galvanic Isolation Barriers Table 4-1 Control I/O Terminal Signals Control Terminal Signals Figure 4-10 Positive/Negative Logic Digital Input Signal InversionsJumper Selections on the OPT-A9 Basic Board Figure 4-11 Jumper Blocks on OPT-A9 AI1 Mode Figure 4-12 Jumper Selection for OPT-A9AI2 Mode AO1 Mode Figure 4-14 Control Unit Installed into the Mounting Box Installing the Control Unit Mounting BoxControl Unit Mounting Box Figure 4-13 Control Unit Mounting Box Table 4-2 Installing the Control Unit Mounting Box January MN04005001E Table 4-2 Installing the Control Unit Mounting Box Continued Internal Connections Connections between Power Unit ASIC and Driver Boards CH61, CH62 and CH72 Table 4-3 Terminals CH61, CH62 and CH72 Figure 4-15 Terminals and Connections between ASIC and Driver BoardX9 OEVA feedback X15 Charging relay output X6 DC terminal X29 Flow supervision input Connect to WL on Phase V/W driver board Table 4-4 Terminals CH63 Table 4-5 Terminals between Driver Boards CH64 and CH74 Figure 4-18 Remove Cover to Access Power Unit Connections between Power Unit ASIC and the Control UnitConnections with Round Cable Connections with Optical Cable Table 4-6 Terminals on Adapter Board Figure 4-19 Optical Cable Adapter BoardSupply voltage 24Vin from power unit Control board connection Chapter 5 - Menu Information Indicators on the Keypad DisplayKeypad Operation Figure 5-1 Control Keypad and Drive Status Indications Table 5-1 Drive Status Indicators Drive Status IndicatorsControl Place Indicators Table 5-2 Control Place Indicators Status LEDs Green - Green - Red Keypad PushbuttonsTable 5-3 Status LEDs Green - Green - Red Text Lines Table 5-5 Button Descriptions Menu Navigation Figure 5-3 Keypad Display DataMonitor Figure 5-4 Keypad Navigation Chart Figure 5-5 Monitoring Menu Monitoring Menu M1 Parameter Menu M2 Table 5-6 Monitored Signals Figure 5-6 Parameter Value Change Procedure Keypad Control Menu M3Table 5-7 Keypad Control Parameters, M3 Selection of Control Place Figure 5-7 Selection of Control Place Keypad ReferenceKeypad Direction Active Faults Menu M4 Figure 5-8 Normal State, No FaultsSTOP Button Activated Figure 5-9 Fault Display Table 5-8 Fault Types Fault TypesFault Time Data Record Fault Type Symbol Fault History Menu M5 Table 5-9 Fault Time Recorded DataReal Time Record Table 5-10 Real Time Record System Menu M6 Figure 5-10 Fault History Menu Table 5-11 System Menu Functions 5-16 Table 5-11 System Menu Functions Continued Selection of Language Figure 5-11 Selection of Language Application SelectionFigure 5-12 Change of Application Parameter Sets S6.3.1 Copy ParametersFigure 5-13 Storing and Loading of Parameter Sets Upload parameters to keypad To keypad, S6.3.2 Automatic Parameter Backup P6.3.4 Figure 5-14 Parameter Copy to KeypadDownload parameters to drive From keypad, S6.3.3 Parameter Comparison Figure 5-15 Parameter ComparisonP2.1.2= 20.0 Hz Password S6.5.1 Figure 5-16 Password SettingSecurity Figure 5-17 Parameter Locking Parameter Lock P6.5.2Start-Up Wizard P6.5.3 Figure 5-18 Activation of Start-Up Wizard Figure 5-20 Keypad Settings Submenu Keypad SettingsDefault Page P6.6.1 Figure 5-21 Default Page Function Timeout Time P6.6.3 Default page in the operating menu P6.6.2Figure 5-22 Timeout Time Setting Contrast Adjustment P6.6.4 Hardware Settings HMI Acknowledge Timeout P6.7.3Figure 5-23 HMI Acknowledge Timeout System info Number of retries to receive HMI acknowledgement P6.7.4Total Counters Table 5-12 Counter Pages Figure 5-24 Counter Reset Table 5-13 Resettable CountersTrip Counters Software S6.8.3 Table 5-15 Applications Information Pages Applications S6.8.4Figure 5-25 Applications Info Submenu Hardware S6.8.5 Figure 5-26 Expander Board Information Menus Expander Boards S6.8.6Debug Menu S6.8.7 Expander Board Menu M7 Expander Board Parameters Further Keypad FunctionsTable 5-17 Expander Board Parameters Board OPTA1 Figure 5-27 Expander Board Information Menu Chapter 6 - Start-Up Safety Precautions Sequence of Operation Page LCX9000 Liquid-Cooled Drives User Manual Table A-1 Fault Codes Appendix A - Fault Codes Table A-1 Fault Codes Continued Table A-1 Fault Codes Continued Load Test with Motor DC Link Test without Motor LCX9000 Liquid-Cooled Drives User Manual Main Circuit and Control Diagrams Figure B-1 Main Circuit and Control Diagram, CH3Appendix B - Technical Reference Figure B-3 Main Circuit and Control Diagram, CH5 Figure B-2 Main Circuit and Control Diagram, CH4Term ATerm Figure B-5 Main Circuit and Control Diagram, CH61, Control Figure B-4 Main Circuit and Control Diagram, CH61SPF1 H8...H13 Figure B-6 Main Circuit and Control Diagram, CH63, Module Figure B-7 Main Circuit and Control Diagram, CH63, ModuleVB00491 Figure B-9 Main Circuit and Control Diagram, CH72 Figure B-8 Main Circuit and Control Diagram, CH63, Control Figure B-11 Main Circuit and Control Diagram, CH74, Phase U Figure B-10 Main Circuit and Control Diagram, CH72, Control Figure B-12 Main Circuit and Control Diagram, CH74, Control Fan Dimensions Figure B-13 Fan Mounting Pallet - Hot Dip Zinc CoatedFigure B-14 Fan Support LCX9000 Liquid-Cooled Drives User Manual B-10 Page Eaton Electrical Inc Company Information2007 Eaton Corporation All Rights Reserved Printed in USA Publication No. MN04005001E/CPG January