Multimonitoring Items P6.5.4, Keypad Settings | J. T. Eaton LCX9000

Multimonitoring Items (P6.5.4)

LCX9000 Liquid-Cooled Drives User Manual

January 2007

Multimonitoring Items (P6.5.4)

The alphanumeric keypad features a display where you can monitor up to three actual values at the same time — see Monitoring Menu (M1) on Page 5-7and the manual of the application you are using. On page P6.5.4 of the System Menu, you can deﬁne whether the operator can replace the values monitored with other values. See below.

56.5.4	56.5.4	56.5.4
Multimon. items	Multimon. items	Multimon. items
ChangeEnable	ChangeEnable	ChangeDisable

Figure 5-19: Disabling the Change of Multimonitoring Items

Keypad Settings

In the Keypad Settings submenu under the System menu, you can further customize your drive’s operator interface.

Locate the Keypad Setting submenu (S6.6). Under the submenu, there are four pages (P#) associated with the keypad operation:

5.6.6				P6.6.
Keypad settings				Default page
P1		P5		0.
P1		P5		0.

Figure 5-20: Keypad Settings Submenu

Default Page (P6.6.1)

Here you can set the location (page) to which the display automatically moves when the Timeout Time (see below) has expired or the power is switched on to the keypad.

If the default page is 0, the function is not activated, i.e. the latest displayed page remains on the keypad display. Pressing Menu Button Right takes you to the edit mode. Change the number of the Main menu with the Browser buttons. To edit the number of the submenu/ page, press Menu Button Right. If the page you want to move to by default is at the third level, repeat the procedure. Conﬁrm the new default page with the ENTER button. You can return to the previous menu at any time by pressing Menu Button Left.

P6.6.	P6.6.	P6.6.
Default page	Default page	Default page
0.	0.	1.

Confirm Change

Repeat to Set

Default Submenu/Page

Cancel

Figure 5-21: Default Page Function

MN04005001E

For more information visit: www.EatonElectrical.com

5-23

Image 99

J. T. Eaton LCX9000 Multimonitoring Items P6.5.4, 19 Disabling the Change of Multimonitoring Items, Keypad Settings

Contents

LCX9000 Liquid-Cooled Drives User Manual January Supersedes SeptemberMN04005001E Page Important Notice - Please Read CHAPTER 4 - CONTROL WIRING AND INTERNAL CONNECTIONS Table ofContents List of Figures List of Figures Continued List of Tables Table 5-11 System Menu Functions List of Tables ContinuedTable 5-13 Resettable Counters Table A-1 Fault Codes Safety Deﬁnitions and SymbolsHazardous High Voltage Warnings Warnings, Cautions and Notices Cautions Motor and Equipment Safety Grounding and Ground Fault Protection Receiving and Inspection Chapter 1 - Overview L C X 0 1 6 A 0 - 4 A 2 B Maintenance Technical DataStorage and Shipping LCX9000 Liquid-Cooled Drives User Manual Figure 1-1 Liquid-Cooled Drive Principal Block Diagram Drives Power RatingsPage Page Table 1-4 Technical Information Speciﬁcations 1-10 Table 1-4 Technical Information Continued Chapter 2 - Installation MountingLifting the Drive Figure 2-2 LCX9000 Liquid-Cooled Drive, CH3 Liquid-Cooled DimensionsTable 2-1 One-Module Drive Dimensions Mounting Base Included Drives Consisting of One Module Top View Figure 2-3 LCX9000 Liquid-Cooled Drive, CH4Figure 2-4 LCX9000 Liquid-Cooled Drive, CH5 Bottom View Figure 2-6 LCX9000 Liquid-Cooled Drive, CH72 Figure 2-5 LCX9000 Liquid-Cooled Drive, CH61 Table 2-2 Several Module Drive Dimensions Mounting Bracket Included Drives Consisting of Several ModulesFigure 2-7 Drive Mounted Inside Mounting Bracket Figure 2-8 LCX9000 Liquid-Cooled Drive with Mounting Bracket, CH63 12-Pulse Supply Figure 2-9 LCX9000 Liquid-Cooled Drive, CH74, IP00Bottom 6-Pulse Supply Table 2-4 Drinking Water Quality Recommendations - Maximum Values CoolingDrinking Water Speciﬁcation Table 2-3 Drinking Water Chemical Speciﬁcation Table 2-6 Process Water Speciﬁcation Table 2-5 Drinking Water Quality Recommendations - Desired Values Figure 2-10 Example of Cooling System ExchangerHeat Table 2-7 Information About Cooling Agent and Its Circulation Figure 2-11 Example PI-Diagram of Cooling System and Connections Table 2-9 Coolant Volumes and Temperatures Figure 2-12 Safe Operating Conditions in Relation to Condensation Condensation Figure 2-14 External Thread of Hose Table 2-10 Liquid Connector Types All Pressure Values at Nominal FlowCooling System Connections Figure 2-13 Aluminum Hose Adapters Pressure Losses Table 2-11 Pressure Losses - CH6x Figure 2-15 Pressure Loss - CH6xOutﬂow Hoses and rubber EPDM only aluminium other stainless and acid-proof materials Table 2-12 Pressure Losses - CH7xFigure 2-16 Pressure Loss - CH7x The following main line hose materials are acceptable plastic PVC Fast Connector Lock Screw, Cable Seal and Clamp Installation of Flow SwitchAbout Flow Switch Installation Figure 2-17 Flow Switch Hose Connection, Fast Connector Electrical External Cooling Fan for CH4 Figure 2-18 Direction of Coolant Circulation Drive Derating Input Chokes Table 2-16 Input Choke Dimensioning, 6-Pulse Supply Sizes 87 - 145A and 590A Installation of Input ChokeFigure 2-19 Example of Input Chokes for Liquid-Cooled Sizes Up to 62A Figure 2-20 Example of Input Chokes for Liquid-Cooled January Table 2-17 Choke Dimensions Sizes 23 - 145A and 590A Table 2-18 Choke Dimensions Sizes 261 - 1150A LCX9000 Liquid-Cooled Drives User Manual Motor Cable Chapter 3 - Power WiringPower Connections Mains Cable Table 3-1 Cable Types Required to Meet Standards Cable DataTable 3-2 Cable Sizes 400 Three grounding terminals per mounting plate, see Page Table 3-2 Cable Sizes 400 - 500V ContinuedUnits with 6-pulse supply Units with 12-pulse supply Table 3-3 Cable Sizes 525 Table 3-4 Tightening Torques of BoltsSee the tightening torques of bolts in Table Table 3-5 Fuse Sizes for LCX9000 Liquid-Cooled 500V Drives Fuse Sizes, Drives Fuse information Table 3-6 Fuse Sizes for LCX9000 Liquid-Cooled 690V Drives Cable Installation Instructions The maximum length of the motor cables is 984 feet 300m4. If cable insulation checks are needed, see Page Figure 3-1 Maximum Terminal Stresses Figure 3-2 Installation Space Installation Space Grounding of Power Unit Cable Installation and the UL StandardsFigure 3-3 Grounding Terminal on Mounting Plate Cable and Motor Insulation Checks 3-12 Figure 4-1 Control Board Chapter 4 - Control Wiring and Internal Connections Figure 4-3 Drives Connected in Parallel Figure 4-2 Basic and Option Board Connections of the Control Board WRONG Terminal J1 Upper Control Board Power-UpFigure 4-4 Connection of Control Board Cable from the Power Board See Figures 4-4 and Figure 4-6 I/O Terminals of the Two Basic Boards Figure 4-5 Connection of Control Board Cable from the Power BoardControl Connections CORRECT Terminal J2 Lower Figure 4-8 General Wiring Diagram of the Basic Relay Board OPT-A2 Figure 4-7 General Wiring Diagram of the Basic I/O Board OPT-A9 Control Cables Galvanic Isolation BarriersFigure 4-9 Galvanic Isolation Barriers Table 4-1 Control I/O Terminal Signals Control Terminal Signals Figure 4-11 Jumper Blocks on OPT-A9 Digital Input Signal InversionsFigure 4-10 Positive/Negative Logic Jumper Selections on the OPT-A9 Basic Board AO1 Mode Figure 4-12 Jumper Selection for OPT-A9AI1 Mode AI2 Mode Figure 4-13 Control Unit Mounting Box Installing the Control Unit Mounting BoxFigure 4-14 Control Unit Installed into the Mounting Box Control Unit Mounting Box Table 4-2 Installing the Control Unit Mounting Box January MN04005001E Table 4-2 Installing the Control Unit Mounting Box Continued Internal Connections Connections between Power Unit ASIC and Driver Boards X29 Flow supervision input Figure 4-15 Terminals and Connections between ASIC and Driver BoardCH61, CH62 and CH72 Table 4-3 Terminals CH61, CH62 and CH72 X9 OEVA feedback X15 Charging relay output X6 DC terminal Connect to WL on Phase V/W driver board Table 4-4 Terminals CH63 Table 4-5 Terminals between Driver Boards CH64 and CH74 Connections with Optical Cable Connections between Power Unit ASIC and the Control UnitFigure 4-18 Remove Cover to Access Power Unit Connections with Round Cable Control board connection Figure 4-19 Optical Cable Adapter BoardTable 4-6 Terminals on Adapter Board Supply voltage 24Vin from power unit Figure 5-1 Control Keypad and Drive Status Indications Indicators on the Keypad DisplayChapter 5 - Menu Information Keypad Operation Table 5-2 Control Place Indicators Drive Status IndicatorsTable 5-1 Drive Status Indicators Control Place Indicators Text Lines Keypad PushbuttonsStatus LEDs Green - Green - Red Table 5-3 Status LEDs Green - Green - Red Table 5-5 Button Descriptions Menu Navigation Figure 5-3 Keypad Display DataMonitor Figure 5-4 Keypad Navigation Chart Figure 5-5 Monitoring Menu Monitoring Menu M1 Parameter Menu M2 Table 5-6 Monitored Signals Figure 5-6 Parameter Value Change Procedure Keypad Control Menu M3Table 5-7 Keypad Control Parameters, M3 Selection of Control Place Figure 5-7 Selection of Control Place Keypad ReferenceKeypad Direction Active Faults Menu M4 Figure 5-8 Normal State, No FaultsSTOP Button Activated Fault Type Symbol Fault TypesFigure 5-9 Fault Display Table 5-8 Fault Types Fault Time Data Record Table 5-10 Real Time Record Table 5-9 Fault Time Recorded DataFault History Menu M5 Real Time Record System Menu M6 Figure 5-10 Fault History Menu Table 5-11 System Menu Functions 5-16 Table 5-11 System Menu Functions Continued Selection of Language Figure 5-11 Selection of Language Application SelectionFigure 5-12 Change of Application Upload parameters to keypad To keypad, S6.3.2 Copy ParametersParameter Sets S6.3.1 Figure 5-13 Storing and Loading of Parameter Sets Automatic Parameter Backup P6.3.4 Figure 5-14 Parameter Copy to KeypadDownload parameters to drive From keypad, S6.3.3 Parameter Comparison Figure 5-15 Parameter ComparisonP2.1.2= 20.0 Hz Password S6.5.1 Figure 5-16 Password SettingSecurity Figure 5-18 Activation of Start-Up Wizard Parameter Lock P6.5.2Figure 5-17 Parameter Locking Start-Up Wizard P6.5.3 Figure 5-21 Default Page Function Keypad SettingsFigure 5-20 Keypad Settings Submenu Default Page P6.6.1 Contrast Adjustment P6.6.4 Default page in the operating menu P6.6.2Timeout Time P6.6.3 Figure 5-22 Timeout Time Setting Hardware Settings HMI Acknowledge Timeout P6.7.3Figure 5-23 HMI Acknowledge Timeout Table 5-12 Counter Pages Number of retries to receive HMI acknowledgement P6.7.4System info Total Counters Software S6.8.3 Table 5-13 Resettable CountersFigure 5-24 Counter Reset Trip Counters Hardware S6.8.5 Applications S6.8.4Table 5-15 Applications Information Pages Figure 5-25 Applications Info Submenu Expander Board Menu M7 Expander Boards S6.8.6Figure 5-26 Expander Board Information Menus Debug Menu S6.8.7 Figure 5-27 Expander Board Information Menu Further Keypad FunctionsExpander Board Parameters Table 5-17 Expander Board Parameters Board OPTA1 Chapter 6 - Start-Up Safety Precautions Sequence of Operation Page LCX9000 Liquid-Cooled Drives User Manual Table A-1 Fault Codes Appendix A - Fault Codes Table A-1 Fault Codes Continued Table A-1 Fault Codes Continued Load Test with Motor DC Link Test without Motor LCX9000 Liquid-Cooled Drives User Manual Main Circuit and Control Diagrams Figure B-1 Main Circuit and Control Diagram, CH3Appendix B - Technical Reference ATerm Figure B-2 Main Circuit and Control Diagram, CH4Figure B-3 Main Circuit and Control Diagram, CH5 Term H8...H13 Figure B-4 Main Circuit and Control Diagram, CH61Figure B-5 Main Circuit and Control Diagram, CH61, Control SPF1 Figure B-6 Main Circuit and Control Diagram, CH63, Module Figure B-7 Main Circuit and Control Diagram, CH63, ModuleVB00491 Figure B-9 Main Circuit and Control Diagram, CH72 Figure B-8 Main Circuit and Control Diagram, CH63, Control Figure B-11 Main Circuit and Control Diagram, CH74, Phase U Figure B-10 Main Circuit and Control Diagram, CH72, Control Figure B-12 Main Circuit and Control Diagram, CH74, Control Fan Dimensions Figure B-13 Fan Mounting Pallet - Hot Dip Zinc CoatedFigure B-14 Fan Support LCX9000 Liquid-Cooled Drives User Manual B-10 Page Publication No. MN04005001E/CPG January Company InformationEaton Electrical Inc 2007 Eaton Corporation All Rights Reserved Printed in USA