Fan Dimensions, Figure B-14 Fan Support | J. T. Eaton LCX9000

Fan Dimensions

LCX9000 Liquid-Cooled Drives User Manual

January 2007

Fan Dimensions

	.51				29.45				.51
	(13)				(748)				(13)
	.18					30.12			.18
	(4.5)	1.46	R .23			(765)		1.46	(4.5)
.01		1.46	R .23					1.46	.87
.01	R .11	(37)	(5.8)		27.56			(37)	.87
(3)					27.56				(22)
(3)					(700)				(22)
	(2.9)				(700)
	(2.9)
2.72										2.95
(69)										(75)
.01	.49		.75			Dia. .43 Dia. .17		.75	.87 .98	.41
.01	.49		(19)		28.98	(11)	(4.2)	(19)	.87 .98	(10.5)
(3)	(12.5)				28.98				(22) (25)
(3)	(12.5)				(736)				(22) (25)
	Typ.			30.47	(736)
	Typ.			30.47
				(774)

Figure B-13: Fan Mounting Pallet — Hot Dip Zinc Coated

Approximate Dimensions in Inches (mm)

.30	5.91
(7.5)	(150)
Dia. .23	1.50
(5.8)	(38)
	6.50		1.46	.26
.85	(165)	.85	(37)	.26
.85	4.80	.85	.98	(6.5)
(21.5)	4.80	(21.5)	.98
	(122)		(25)
			105°
				.75
				(19)
			4.92	5.39
4.13			4.92	(137)
4.13			(125)
(105)	Dia. 4.53		(125)
(105)	Dia. 4.53
	(115)		4.13
			(105)

2.46

(62.5)

2.46

(62.5)

.39

(10)

.39	4.13	.39
(10)	(105)	(10)

4.92

(125)

Figure B-14: Fan Support

B-8

For more information visit: www.EatonElectrical.com

MN04005001E

Image 124

J. T. Eaton LCX9000 Fan Dimensions, Figure B-13 Fan Mounting Pallet - Hot Dip Zinc Coated, Figure B-14 Fan Support

Contents

User Manual January Supersedes September LCX9000 Liquid-Cooled DrivesMN04005001E Page Important Notice - Please Read Table of CHAPTER 4 - CONTROL WIRING AND INTERNAL CONNECTIONSContents List of Figures List of Figures Continued List of Tables List of Tables Continued Table 5-13 Resettable CountersTable A-1 Fault Codes Table 5-11 System Menu Functions Deﬁnitions and Symbols SafetyHazardous High Voltage Warnings, Cautions and Notices Warnings Cautions Grounding and Ground Fault Protection Motor and Equipment Safety Chapter 1 - Overview Receiving and Inspection L C X 0 1 6 A 0 - 4 A 2 B Technical Data MaintenanceStorage and Shipping LCX9000 Liquid-Cooled Drives User Manual Figure 1-1 Liquid-Cooled Drive Principal Block Diagram Power Ratings DrivesPage Page Speciﬁcations Table 1-4 Technical Information Table 1-4 Technical Information Continued 1-10 Mounting Chapter 2 - InstallationLifting the Drive Liquid-Cooled Dimensions Table 2-1 One-Module Drive Dimensions Mounting Base IncludedDrives Consisting of One Module Figure 2-2 LCX9000 Liquid-Cooled Drive, CH3 Figure 2-3 LCX9000 Liquid-Cooled Drive, CH4 Figure 2-4 LCX9000 Liquid-Cooled Drive, CH5Bottom View Top View Figure 2-5 LCX9000 Liquid-Cooled Drive, CH61 Figure 2-6 LCX9000 Liquid-Cooled Drive, CH72 Drives Consisting of Several Modules Table 2-2 Several Module Drive Dimensions Mounting Bracket IncludedFigure 2-7 Drive Mounted Inside Mounting Bracket Figure 2-8 LCX9000 Liquid-Cooled Drive with Mounting Bracket, CH63 Figure 2-9 LCX9000 Liquid-Cooled Drive, CH74, IP00 Bottom6-Pulse Supply 12-Pulse Supply Cooling Drinking Water SpeciﬁcationTable 2-3 Drinking Water Chemical Speciﬁcation Table 2-4 Drinking Water Quality Recommendations - Maximum Values Table 2-5 Drinking Water Quality Recommendations - Desired Values Table 2-6 Process Water Speciﬁcation Exchanger Figure 2-10 Example of Cooling SystemHeat Figure 2-11 Example PI-Diagram of Cooling System and Connections Table 2-7 Information About Cooling Agent and Its Circulation Table 2-9 Coolant Volumes and Temperatures Condensation Figure 2-12 Safe Operating Conditions in Relation to Condensation Table 2-10 Liquid Connector Types All Pressure Values at Nominal Flow Cooling System ConnectionsFigure 2-13 Aluminum Hose Adapters Figure 2-14 External Thread of Hose Figure 2-15 Pressure Loss - CH6x Pressure Losses Table 2-11 Pressure Losses - CH6xOutﬂow Hoses and Table 2-12 Pressure Losses - CH7x Figure 2-16 Pressure Loss - CH7xThe following main line hose materials are acceptable plastic PVC rubber EPDM only aluminium other stainless and acid-proof materials Installation of Flow Switch About Flow Switch InstallationFigure 2-17 Flow Switch Hose Connection, Fast Connector Electrical Fast Connector Lock Screw, Cable Seal and Clamp Figure 2-18 Direction of Coolant Circulation External Cooling Fan for CH4 Drive Derating Table 2-16 Input Choke Dimensioning, 6-Pulse Supply Input Chokes Installation of Input Choke Figure 2-19 Example of Input Chokes for Liquid-Cooled Sizes Up to 62AFigure 2-20 Example of Input Chokes for Liquid-Cooled Sizes 87 - 145A and 590A Table 2-17 Choke Dimensions Sizes 23 - 145A and 590A January Table 2-18 Choke Dimensions Sizes 261 - 1150A LCX9000 Liquid-Cooled Drives User Manual Chapter 3 - Power Wiring Power ConnectionsMains Cable Motor Cable Cable Data Table 3-1 Cable Types Required to Meet StandardsTable 3-2 Cable Sizes 400 Table 3-2 Cable Sizes 400 - 500V Continued Units with 6-pulse supplyUnits with 12-pulse supply Three grounding terminals per mounting plate, see Page Table 3-4 Tightening Torques of Bolts Table 3-3 Cable Sizes 525See the tightening torques of bolts in Table Fuse Sizes, Drives Table 3-5 Fuse Sizes for LCX9000 Liquid-Cooled 500V Drives Table 3-6 Fuse Sizes for LCX9000 Liquid-Cooled 690V Drives Fuse information The maximum length of the motor cables is 984 feet 300m Cable Installation Instructions4. If cable insulation checks are needed, see Page Figure 3-1 Maximum Terminal Stresses Installation Space Figure 3-2 Installation Space Cable Installation and the UL Standards Grounding of Power UnitFigure 3-3 Grounding Terminal on Mounting Plate Cable and Motor Insulation Checks 3-12 Chapter 4 - Control Wiring and Internal Connections Figure 4-1 Control Board Figure 4-2 Basic and Option Board Connections of the Control Board Figure 4-3 Drives Connected in Parallel Control Board Power-Up Figure 4-4 Connection of Control Board Cable from the Power BoardSee Figures 4-4 and WRONG Terminal J1 Upper Figure 4-5 Connection of Control Board Cable from the Power Board Control ConnectionsCORRECT Terminal J2 Lower Figure 4-6 I/O Terminals of the Two Basic Boards Figure 4-7 General Wiring Diagram of the Basic I/O Board OPT-A9 Figure 4-8 General Wiring Diagram of the Basic Relay Board OPT-A2 Galvanic Isolation Barriers Control CablesFigure 4-9 Galvanic Isolation Barriers Control Terminal Signals Table 4-1 Control I/O Terminal Signals Digital Input Signal Inversions Figure 4-10 Positive/Negative LogicJumper Selections on the OPT-A9 Basic Board Figure 4-11 Jumper Blocks on OPT-A9 Figure 4-12 Jumper Selection for OPT-A9 AI1 ModeAI2 Mode AO1 Mode Installing the Control Unit Mounting Box Figure 4-14 Control Unit Installed into the Mounting BoxControl Unit Mounting Box Figure 4-13 Control Unit Mounting Box Table 4-2 Installing the Control Unit Mounting Box Table 4-2 Installing the Control Unit Mounting Box Continued January MN04005001E Connections between Power Unit ASIC and Driver Boards Internal Connections Figure 4-15 Terminals and Connections between ASIC and Driver Board CH61, CH62 and CH72 Table 4-3 Terminals CH61, CH62 and CH72X9 OEVA feedback X15 Charging relay output X6 DC terminal X29 Flow supervision input Table 4-4 Terminals CH63 Connect to WL on Phase V/W driver board Table 4-5 Terminals between Driver Boards CH64 and CH74 Connections between Power Unit ASIC and the Control Unit Figure 4-18 Remove Cover to Access Power UnitConnections with Round Cable Connections with Optical Cable Figure 4-19 Optical Cable Adapter Board Table 4-6 Terminals on Adapter BoardSupply voltage 24Vin from power unit Control board connection Indicators on the Keypad Display Chapter 5 - Menu InformationKeypad Operation Figure 5-1 Control Keypad and Drive Status Indications Drive Status Indicators Table 5-1 Drive Status IndicatorsControl Place Indicators Table 5-2 Control Place Indicators Keypad Pushbuttons Status LEDs Green - Green - RedTable 5-3 Status LEDs Green - Green - Red Text Lines Table 5-5 Button Descriptions Figure 5-3 Keypad Display Data Menu NavigationMonitor Figure 5-4 Keypad Navigation Chart Monitoring Menu M1 Figure 5-5 Monitoring Menu Table 5-6 Monitored Signals Parameter Menu M2 Keypad Control Menu M3 Figure 5-6 Parameter Value Change ProcedureTable 5-7 Keypad Control Parameters, M3 Figure 5-7 Selection of Control Place Keypad Reference Selection of Control PlaceKeypad Direction Figure 5-8 Normal State, No Faults Active Faults Menu M4STOP Button Activated Fault Types Figure 5-9 Fault Display Table 5-8 Fault TypesFault Time Data Record Fault Type Symbol Table 5-9 Fault Time Recorded Data Fault History Menu M5Real Time Record Table 5-10 Real Time Record Figure 5-10 Fault History Menu System Menu M6 Table 5-11 System Menu Functions Table 5-11 System Menu Functions Continued 5-16 Figure 5-11 Selection of Language Application Selection Selection of LanguageFigure 5-12 Change of Application Copy Parameters Parameter Sets S6.3.1Figure 5-13 Storing and Loading of Parameter Sets Upload parameters to keypad To keypad, S6.3.2 Figure 5-14 Parameter Copy to Keypad Automatic Parameter Backup P6.3.4Download parameters to drive From keypad, S6.3.3 Figure 5-15 Parameter Comparison Parameter ComparisonP2.1.2= 20.0 Hz Figure 5-16 Password Setting Password S6.5.1Security Parameter Lock P6.5.2 Figure 5-17 Parameter LockingStart-Up Wizard P6.5.3 Figure 5-18 Activation of Start-Up Wizard Keypad Settings Figure 5-20 Keypad Settings SubmenuDefault Page P6.6.1 Figure 5-21 Default Page Function Default page in the operating menu P6.6.2 Timeout Time P6.6.3Figure 5-22 Timeout Time Setting Contrast Adjustment P6.6.4 HMI Acknowledge Timeout P6.7.3 Hardware SettingsFigure 5-23 HMI Acknowledge Timeout Number of retries to receive HMI acknowledgement P6.7.4 System infoTotal Counters Table 5-12 Counter Pages Table 5-13 Resettable Counters Figure 5-24 Counter ResetTrip Counters Software S6.8.3 Applications S6.8.4 Table 5-15 Applications Information PagesFigure 5-25 Applications Info Submenu Hardware S6.8.5 Expander Boards S6.8.6 Figure 5-26 Expander Board Information MenusDebug Menu S6.8.7 Expander Board Menu M7 Further Keypad Functions Expander Board ParametersTable 5-17 Expander Board Parameters Board OPTA1 Figure 5-27 Expander Board Information Menu Safety Precautions Chapter 6 - Start-Up Sequence of Operation Page January Appendix A - Fault Codes Table A-1 Fault Codes Table A-1 Fault Codes Continued Table A-1 Fault Codes Continued Load Test with Motor DC Link Test without Motor January Figure B-1 Main Circuit and Control Diagram, CH3 Main Circuit and Control DiagramsAppendix B - Technical Reference Figure B-2 Main Circuit and Control Diagram, CH4 Figure B-3 Main Circuit and Control Diagram, CH5Term ATerm Figure B-4 Main Circuit and Control Diagram, CH61 Figure B-5 Main Circuit and Control Diagram, CH61, ControlSPF1 H8...H13 Figure B-7 Main Circuit and Control Diagram, CH63, Module Figure B-6 Main Circuit and Control Diagram, CH63, ModuleVB00491 Figure B-8 Main Circuit and Control Diagram, CH63, Control Figure B-9 Main Circuit and Control Diagram, CH72 Figure B-10 Main Circuit and Control Diagram, CH72, Control Figure B-11 Main Circuit and Control Diagram, CH74, Phase U Figure B-12 Main Circuit and Control Diagram, CH74, Control Figure B-13 Fan Mounting Pallet - Hot Dip Zinc Coated Fan DimensionsFigure B-14 Fan Support January B-10 Page Company Information Eaton Electrical Inc2007 Eaton Corporation All Rights Reserved Printed in USA Publication No. MN04005001E/CPG January