Manuals / Brands / Photography / Security Camera / JVC / Photography / Security Camera

JVC LST0728-001C Note :, Camera Control Terminal (VR-N900U), 3 Mount to the rack using screws C, When operating method is different

1 168

Download 168 pages, 22.21 Mb

Camera Control Terminal (VR-N900U)

Use connection cables according to the table below. Also make sure that you read through the instruction manual of the equipment to be connected.

Signal	Pin No.

RX+	1

RX-	2

TX-	3

TX+	4

GND	5

NC	6

NC	7

NC	8

NC	9

(D-sub 9 pin, male)

Differences when operating VR-N1600U/E and VR-N900U

The name of control buttons and operating methods may vary between VR-N1600U/E and VR-N900U. Such circumstances will be indicated using the rules below.

When name of control button is different

AIndicated accordingly using [button name of VR-N1600U/E] and (button name of VR-N900U)

Bmark is inserted at the end of the sentence

AB

Press the [16/ENTER](ZOOM IN/ENTER)button. When operating method is different

The operation for the respective model is stated, and the model name is indicated at the end of the sentence.

Mounting to a Rack

Use the supplied rack mount bracket to mount this unit to the EIA rack. For the installation to the rack, consult the specialist or dealer.

1 Mount the rack mount bracket using screw (1)

●Use the 4 screws (M4 x 10 mm) supplied to fasten this unit at the two sides.

2 Remove the foot screws B (4 pcs) at the bottom of the unit

●Remove the foot.

3 Mount to the rack using screws C

●Use the 4 screws (M5 x 11 mm) supplied to fasten this unit to the rack.

Rack Mount

Bracket

(4 Screws)

Note :

●Do not place any object on this unit when it is mounted to the rack. Doing so may cause it to lose balance and drop or fall, hence resulting in injuries or damages.

●When mounting more than one of this unit to the rack, make sure to mount each at a distance that is at least equivalent to one unit.

●When remounting the removed foot, make sure to use same screws (M3x6 mm). Using a longer screw may cause malfunction.

21

Contents

VR-N1600U/E(A) VR-N900U(B) Powered by Milestone Page SAFETY PRECAUTIONS (for USA) SAFETY PRECAUTIONS PRECAUTIONS WHEN MOUNTING RACK CAUTION INFORMATION (FOR CANADA) RENSEIGNEMENT (POUR CANADA) WARNING (FOR EUROPE): SICHERHEITSVORKEHRUNGEN (for Germany) Page Page E/VR-N900U Getting Started Supports RAID1 (VR-N1600U/E) Automatic detection of network cameras Supports HDD expansion Simultaneous recording up to 9 channels at 120 ips (VR-N900U) 1. Grant of Use 2. Copyright 3. No Warranties 4. Limitation of Liability 5. Miscellaneous Microsoft Software License Terms for: WindowsXP Embedded Runtime 2 Additional Licensing Requirements and/or Use Rights 3 Scope of License Page Microsoft Software License Terms for: (continued) 4 Windows Update Agent (also known as Software Update Services) Product Support Backup Copy Proof Of License 12 Liability Limitations 13 Export Restrictions Getting Started Preparation Basic Operation Applications Others Locations of Storage and Use Handling Precautions Precautions for Handling Hard Disk Drive Clock Precautions when Moving this Unit Precautions for Handling Power Cords Maintenance Energy Conservation Copyright CDE L[STOP(PB)] Button M[PLAY] Button N[SKIP] Button OJog dial PShuttle dial W X YZ a b ef h j l n g i km o Front Panel CDE F G H I J K L M N O A [OPERATE] Button/Indicator J[SEARCH] Button K[KEY] Button L[ALARM CLEAR] Button M[REC/STOP] Button N[STOP(PB)] Button W[POWER] switch X[AC IN 120V H 240VH 50Hz/60Hz] power input terminal Y[RESET] Z[AUDIO IN 1/AUDIO IN 2] audio input terminals 1/2 (RCA) a[AUDIO OUT] audio output terminal (RCA) j[ALARM IN 1 to 4] alarm input terminals 1 to k[EMERGENCY] emergency input terminal l[ALARM RESET] alarm reset input terminal m[EXT REC IN] external recording input terminal n[OPE ON/OFF] Operate ON/OFF terminal Page Camera Control Terminal (VR-N900U) When name of control button is different Press the [16/ENTER](ZOOM IN/ENTER)button. When operating method is different 1 Mount the rack mount bracket using screw (1) Setting Operation Lock Canceling Operation Lock Before Starting Up Starting the Unit 1 Turn on the power switch at the rear panel Selecting a Language 1 Select a language Automatic Registration of Cameras 2 Check to ensure that the camera is detected 3 Replace the detected camera accordingly in sequence Automatic Registration of Cameras (continued) 7 Enter the password for the network camera 10 Repeat the steps from 5 to 7 for every detected camera 12 Repeat Step 10 for each camera Preparation VR-N1600U/E Page Entering Characters Using a Mouse 1 Press the [KEY] button on the front panel 3 Click on the character 1 Press the [KEY] button 2 Move the mouse pointer with the keypad (arrow key) Page Basic Operation Switching the Power On 1 Connect the power cable 2 Turn AONB the power switch at the rear panel Switching the Power Off Page 1 Press and hold the [REC/STOP] button for at least 2 seconds 3 Select an item For details on the main menu settings, refer to [Main Menu List] (A Page 68) Page 1 Press the [SELECT] button 2 Enter the camera number with the keypad Operating the Camera Pan/Tilt 1 Press the [PTZ/PRESET] button to switch the keypad to the PTZ mode 2 Press the 1 to 9 key on the keypad Zoom In/Zoom Out 1 Select [Live] from the main menu Viewing Images Using the PTZ Features 1 Click the PTZ navigation button in the [PTZ Control] section Using Preset Positions Viewing Images Using the PTZ Features (continued) Digital Zoom 1 Click the [v] button on the [Presets] list in the [PTZ Control] section 2 Select a preset position from the preset list Manually Triggering an Event Triggering Outputs Camera Shortcut Menus Displaying the [Browse] Screen 2 When the [Live] screen appears, press the [LIVE/BROWSE] button again Searching Recorded Image Using a Specific Date/Time 1 Press the [SEARCH] button on the [Browse] screen 2 Use the keypad to enter the search date and time Playing, Skipping and Stopping Recorded Images Control using the [PLAY], [SKIP], and [STOP(PB)] buttons on the front panel Playing Back 1 Press the [PLAY] button Skipping Notes: 2 Double-clickthe [Browse] tab on the NVR Viewer Searching Recorded Image Using [Time Navigation] 1 Double-clickthe [Time Navigation] bar on the [Browse] screen 2 Select the search date/time from the box 3 Click the [Go To] button Searching Recorded Image Using the Timeline Browser Timeline Colors and Lines Searching Recorded Image Using Sequence 1 Double-clickthe [Sequence] bar on the [Browse] screen 2 Click [Get Sequence] Searching Recorded Image from the Alert List 1 Double-clickthe [Alerts] bar on the [Browse] screen 2 Click [] on the [Alerts] list and select an event from the list 3 Click the [Get List] button Smart Search Browse Button [Time] Slider [Playback] Slider Listening to Audio Sound Burning a CD/DVD 1Double-clickthe [Export] bar on the [Browse] screen 2Enter the start date and time 3Enter the end date and time Burning a CD/DVD (continued) 5 Select the export format if you have selected [AVI/JPEG Export...] 6 Select the required frame rate if you have selected the [AVI] format 10 Specify the export destination 16 Press the [Burn] button 11 Click [Export] 12 When export is complete, connect the CD/DVD drive to this unit 13 Press and hold the [FUNCTION] key in front, and press [4] on the keypad Deleting Temporary Files (Operation on the Unit) 1 Select the temporary files you want to delete from the data list 2 Click the [Erase Sel Data] button Deleting Data from a CD-RW(Operation on the Unit) 1 Insert the CD-RW Operation from a Surveillance Computer 1 Double-clickthe [Print] bar on the [PLAY] screen 2 Click the [Print...] button in the [Print] section 4 Click the [Print] button to start printing Recording Modes Recording Control Mode (A Page 53) Manual Recording Mode [EXT REC IN] Signal Recording Mode Emergency Recording Mode Selecting the Recording Control Mode Selecting the Manual Recording Mode 1 Press the [REC/STOP] button Scheduler Setting 1 Select [Camera Record Setting] from the main menu Scheduler Setting (continued) 4 Select [Set] from [Mode] 5 Select the [Online] check box 6 Specify the date to switch online in the calendar section 7 The Schedule Settings window appears Camera/Alert Scheduler Screen A B C Display Bar Specifying Image Recording Settings 2 Select a camera from [Device Manager] and click [Settings...] Settings Conditionally Settings (continued) Setting Picture Quality 2 Select a camera from [Device Manager] and click [Camera Settings] 3 Click [Image Quality...] Specifying Audio Recording Settings Precautions when enabling the analog audio source of VR-N1600U/E Renaming Cameras and Assigning Camera Numbers 1 Select a camera name and right-clickon it, followed by clicking [Edit] Screen Display (Groups and Views) Creating Groups and Views Creating a Group 1 Select [Screen Setup] from the main menu 2 Select the root folder in which you want to create a new group 3 Click the [Create New Group] button in the [Views] section 2 Click the [Rename] button Creating Groups and Views (continued) 3 Enter a name for the new view 3 Overwrite the existing group or view name with a new name Renaming a Group/View Adding Cameras to a View 1 Select a view 2 Click the [+] mark to the left of [Server] under [System Overview] Adjusting Camera Settings 1 Select the camera you want to adjust on the [Screen Setup] screen Using Your Views on Different Computers Adjusting Camera Settings (continued) 4 To adjust the settings on other cameras, repeat Steps 2 to 1 Double-clickthe [Setup] tab on the NVR Viewer 2 Select the folder you want to use in the [Views] section 3 Release the mouse button at the position Adding Hot Spots (Enlarged Images) Using the [Html Page] 1 Click [Html Page] under [System Overview] 2 Drag and drop at the required position using the mouse Type in the URL and click [OK] Select [Html Page] under [Views], and specify Applications List of Menu Screens Unit Setting Unit Setting 1 (continued) NONE Average File Size Page OS Setting Network Adapter OS Setting (continued) Page Image Server Setting Page Image Server Setting (continued) Page Auto Detect Setting Enable Page Page Camera Record Setting Page Optional Installation 2 Click [Add Device...] 3 Enter the IP address or DNS host name that can be identified by the system 4 If an administrator password is specified for the device, enter the password 5 Enter a unique name for the device that has been detected 6 Click [Finish] Page D E F G [CAMERA CONTROL] Terminal at the Rear of VR-N900U (VR-N900U) Stopping the Recording Server Display the [PTZ Preset Positions for Device Name] Window 2 Click the [Service Manager...] button 3 Click the [Pause] button 3 Click the [PTZ Preset Positions...] button Moving to Preset Positions by Events 1 Display the [PTZ Preset Positions for Device Name] window (A Page 90) Defining a Preset Position 2 Move the camera and determine the position using the [PTZ View] 4 Click the [Set Position] button and name the preset position Auto PTZ Patrolling 2 Click the [Setup...] button of [Patrolling] A B C D Auto PTZ Patrolling (continued) Specifying Patrol Timing PTZ Patrolling Actions Upon Detection of Motion 1 Select the [Disable patrolling schedule if motion is detected] check box 2 Select the conditions for resuming PTZ patrolling I/O Settings 1 Click the [I/O Setup...] button on the [Camera Record Setting] screen I/O Settings (continued) Specifying an Input Event 3 Select the required event from the [Available Input Event(S)] list and click the button to add the event 2 Click the [Add new event...] button Input/Output Terminal on Rear Panel Rear Panel Input Terminals Output Terminals Specifying a VMD Event 2 Click the [Add VMD Event(Motion Detection)] button Specifying an Output 2 Click the [Add new output event...] button [Advanced] Screen 1 Click the [Advanced...] button on the [I/O Setup] screen 2 Specify the following items Configuring Event Buttons 2 Select [Global] (apply to all cameras) or a specific camera 3 Click [Add new event...] to add the event button Specifying Generic Events AC B 2 Select Generic and click [Add new event...] AGeneral Event settings BNotification settings CEvent rules string 5 Repeat 2 to 4 for each event Specifying an Output Port Event Notification Settings 2 Click the [Event Notifications...] button 1 Select [I/O Control] from the [Camera Record Setting] screen Camera Output Settings Specifying Output via Motion Detection Select an output from the [All Output] list button between the [All Output] and [On Motion Detected] lists Defining Motion Detection Exclusion Regions Setting Buttons and Check Boxes Specifying Motion Detection 2 Specify [Noise Sensitivity] and [Motion Sensitivity] Page E-mailSettings 1 Click [Camera Recording Administator]-[ArchiveSetup] K J G H 4 Select the camera for which archive is to be created Setting Items and Buttons Precautions when Changing NAS Archive Settings Precautions when Changing Archive Settings Specify the Database Settings 1 Select [Flash Memory Utility] from the main menu Save Setting Date 2 Select [Save Setting Date] 3 Press the [OK] button 4 Select [Remove Flash Memory] Reading Preset Data 2 Select [Load Setting Data] 3 Select the setting to load, followed by pressing [Load] 4 The [Load Setting Data?] confirmation message appears. Press [OK] 5 Press [Close] to return to the [Flash Memory Utility] screen Specifying IP Lease 1 Select [Auto Detect Setting] from [Main Menu] 2 Select [Enable] in [IP Lease] 3 Specify the following items under [IP Lease Parameter] 4 Click [OK] Using the Auto Detect Feature 1VR-N900U 1 Click [Auto Detect] 3 Configure the analog input (VR-N900U) 4 Click [Entry] 1 Exit NVR Viewer 2 Select [Language Setting] from the main menu 3 Select a language 4 Click the [OK] button 1 Select [HDD Utility] from the main menu 1 Select [Return to default setting] from the main menu 2 Click [OK] User Administration User Settings Defining User Rights 1 Select [Restrict user access] in the [User Administration] section 2 Click [User Access...] 3 Select the user for which user right is to be specified from the [User] list 5 Select the camera to allow access from the [Defined Cameras] 6 Click [] to move to [Viewable by selected user] 8 Repeat the same procedures for other users Master/Slave Settings Adding Slave Servers 1Select [Slaves] in the [Master/Slave Setup] section 2Select [Add Slave] on the [Slave Administration] screen 3Select [Hostname]/[Port] on the [Add New Slave] screen 1 Click the [Start] button, followed by clicking [Control Panel] System requirements Computer Network Settings 2 Click [Network and Internet Connections]- [Network Connections] 10 Set [Default gateway] to 3 Select the network to which NVR is connected 11 Click the [OK] button 12 Click the [OK] button on the [Local Area Connections Proparties] screen 4 Right-clickand select [Properties] Install the NVR Viewer on the Computer 3 Click the [Run] button 4 Click [Next] and follow the installation instructions 2 Click [Download and install NVR Viewer locally] Login to the NVR Viewer 1 Double-clickthe NVR Viewer shortcut on the desktop 5 Installation complete Login to NVR Viewer (Continued) 2 Specify your login information in the following fields 3 Click the [Connect] button 4 Set the display language according to the country of use Uses of the NVR Viewer Exiting/Logging Out of the NVR Viewer Logging Out 1 Click the [Log Out] button Exiting Connection 1 Refer to [System Connection Example] Registering camera that supports bidirectional audio Audio Transmission 1 Start up the NVR Viewer to check the live images of the camera 5 Press the [Disconnect] button to disconnect the camera 1 Select [Event Audio Setting] from [Main Menu] A B Audio Copying 1 Click [Audio files copy] on the [Event Audio Setting] screen Setting Copy 2Click [Setting copy] B Copy C Cancel Password Communication Settings 1Click [Communication setting] on the [Event Audio Setting] screen B Transfer port C Transfer Displaying the HDD Meter Changing the HDD Meter Settings 1Insert a commercially available flash memory device into the serial terminal 2Select [Unit Setting 2] from the main menu 3Select the [Enable of SNMP] check box in the [SNMP setting] section 5Specify the SNMP community name 6Press [Copy extension MIB onto the flash memory] in the [SNMP setting] section List of Status that can be Obtained from this Unit List of TRAP Supported by this Unit Compatible Network Cameras Connecting a UPS 2 Select AUPS ModeB and press the [OK] button 3 Connect the UPS communication cable to the [SERIAL] port on the rear panel 4 Connect the power cable of this unit to the UPS power output connector 4 Switch on the power of this unit 5 Check the entry in the [Volume] field, and click the [Initialize] button NAS Pressing a Button for Two Seconds or Longer [REC CONTROL] Combining a Button with the [FUNCTION] Button [FUNCTION] + [REC CONTROL] [FUNCTION] + [LIVE/BROWSE](VR-N1600U/E) 2 Select AOn motionB or AOn eventB Zoom Iris Focus Speed Preset Page Starting the Export Viewer 4 Double-clickthe data folder in the list on the right side of the Explorer 5 Double-click[Browser.exe] in the list on the right side of the Explorer Viewing Exported Data Viewing Data on a Specific Date/Time Using Date/Time Selection 1 Click the [K] button for date selection 2 Select a specific date from the calendar 3 Click the [K] button for time selection, and select a specific time Select a joystick from the selected joystick list 1 Click the [K] button at the top right corner of the screen 2 Select [Joystick Setup] from the menu that appears 5 Assign an action to each joystick button in the [Button Setup] section Disabling Joystick Operation 1 Click [HDD Utility] under [Main Menu] (A Page 116) 2 Click [Details] 6 Click [Close] 7 Click [Main Menu]-[CameraRecord Setting]- [Archive Setup...] (A Page 108) 8 Deselect the [Automatic path selection] check box Page Page 9 channel recording without audio recording or additional HDD upgrade 4 Channel Recording/No Audio Recording/No Additional HDD 4 Channel Recording/2 Channel Audio Recording/No Additional HDD 4 Channel Recording/No Audio Recording/Additional HDD (1 TB x 1 Unit) 4 Channel Recording/2 Channel Audio Recording/Additional HDD (1 TB x 1 Unit) Page Page Page Page Page Page Actions when Warning Indicator Lights Up VR-N1600U/E General Interface Compression Format Recording VR-N900U General