Accessory Connections, External Speakers | Kenwood TM-V71A, TM-V71E

Accessory Connections

nExternal Speakers

If you plan to use external speakers, choose speakers with an impedance of

8 Ω. The external speaker jacks accept a 3.5 mm (1/8”) mono (2-conductor) plug. We recommend using SP-50B speakers.

There are 2 speaker jacks on the rear of the transceiver: SP 1 and SP 2.

Refer to page 71 to determine how the speakers will be used.

SP 1 jack

External speakers (SP-50B)

SP 2 jack

nMicrophone

To communicate using voice, connect the supplied microphone to the MIC jack on the left side of the transceiver. Press firmly on the plug until the locking tab clicks.

MIC jack

Microphone connector

Page 15

Image 15

Kenwood TM-V71A, TM-V71E instruction manual Accessory Connections, External Speakers, Microphone

Contents

144/430 MHz FM Dual Bander 144/440 MHz FM Dual Bander Writing Conventions Followed in this Manual FeaturesThis transceiver has the following main features Thank You One or more of the following statements may be applicable When Condensation Occurs Inside the Transceiver Precautions Contents Using Ctcss Ctcss Frequency ID Using DCS DCS Code IDManual Dialing Automatic dialer VGS-1 Optional Voice Guide & Storage Unit Dtmf Key Lock Options Part Number Quantity Supplied AccessoriesMobile Installation Preparation Mobile Operation Power Cable Connection Fixed Station Operation Fuse Location Fuse Current Rating Located on the DC connectorSupplied DC power cable Replacing Fuses Antenna Connection Front Panel Orientation Accessory Connections External SpeakersMicrophone Front Panel Getting Acquainted 0PF2 REVLOW PF1 Display Indicator Description Appears while accessing the Menu Sub-Panel Rear Panel Microphone MC-59 Press the switch again to switch the transceiver OFF Switching the Power ON/ OFFAdjusting the Volume Press the switch to switch the transceiver on Adjusting the Squelch Selecting a BandBand a left Band SEL control Band B right Band SEL control Selecting Dual band mode/ single band Mode Frequency ranges Selecting a frequency band Selecting an Operating mode VFO ModeMemory Channel Mode Transmitting Call Channel ModePress Call to enter Call Channel mode When you finish speaking, release the PTT switch Press F, Tuning control to access the Menu Menu ModeMenu Access Menu Configuration ANN.SPD DT.SPD MIC.LCK Repeat steps 2 and 3 to enter the remaining characters Rotate the Tuning control to select your desired characterPress the Tuning control to set the selected character Character Entry Key Character Display with each press of the key Microphone Keypad Character Entry Repeater Access Operating Through RepeatersSelecting an Offset Direction Activating the Tone Function Selecting an Offset Frequency Frequency Rotate the Tuning control to select your desired frequencySelecting a Tone Frequency Press F, Tone Automatic Repeater Offset K and E Types Only Transmitting a 1750 Hz Tone Reverse FunctionAutomatic Simplex Checker ASC Press F, Tone 1s to run the Tone Frequency ID scan Tone Frequency ID Memory Channels Simplex & Repeater or ODD-SPLIT Memory CHANNEL?Parameter Simplex Odd-split Storing Simplex and Standard Repeater Frequencies Storing Odd-Split Repeater FrequenciesCall Channel Memory Simplex Recalling a Memory Channel Call Channel Memory Odd-SplitMemory Recall Method Clearing a Memory Channel Turn the transceiver power OFFPress MR + Power on Press the Tuning control to clear the Memory channel Press F, VFO Switching the Memory Name/ Frequency DisplayMemory-TO-VFO TRansfer Channel Display FUnction KEY KEY 1s While KEY + Key Name Programmable Memory PM Application Examples Storing Data in PM Channels Recalling PM ChannelsPress F, PM Auto PM Channel store PM Channel ResetPress F + Power on Press the Tuning control again to reset the PM channels Scan Type Scan Range Scan VFO Scan Selecting a Scan Resume Method To quit Memory Scan, press MR again Memory ScanLocking Out a Memory Channel Press MR 1s Memory Group Channel Range To quit Group Scan, press the Tuning control againGroup Scan Memory Group Link Setting Scan Limits Program ScanPress VFO To quit Program Scan, press VFO again Using Program Scan To quit Call Scan, press Call again To quit MHz Scan, press the Tuning control againMHz Scan Call Scan Continuous Tone Coded Squelch System Ctcss Using Ctcss Press Enter again to complete the setting Press F, Tone 1s Ctcss FREQuency ID Using DCS Rotate the Tuning control to select your desired DCS codeDigital Coded Squelch DCS DCS Code DCS Code ID 1209 1336 1447 1633 697 770 852 941 Dual Tone MULTI-FREQUENCY DtmfManual Dialing Dtmf Hold Storing a Dtmf Code in Memory Automatic Dialer Selecting a Transmit Speed Transmitting Stored Dtmf Codes Selecting a Pause Duration Dtmf Key Lock Storing EchoLink memory What is EchoLink? Transmitting EchoLink Memory TxD RxD Setting Up EchoLink Sysop ModeEchoLink Sysop Mode on TM-V71 EchoLink Sysop Mode OFF TM-V71 Auto Display Brightness POWER-ON MessageAuxiliary Functions Display Brightness To turn Key Lock on or OFF, press F 1s Key LockBacklight Color Microphone Key Lock Beep Volume Key BeepProgrammable VFO Changing the Frequency Step Size Programmable Function Keys Transceiver Front PanelMicrophone Keys Frequency Direct Entry Automatic Power OFF APO Meter Squelch Advanced Intercept Point AIPSquelch Hang Time Switching FM/AM Mode Beat ShiftSpeaker Mute Selecting an Output Power TIME-OUT Timer TOTMute Hang Time Speaker Band Output External Speaker ConfigurationSetup Masking a Band Display Partition Bar Memory Name Location Weather Alert K Type Models OnlyWeather Channel Channel No Enter your password Power On Password Current frequency/code VGS-1 Optional Voice Guide & Storage UnitVoice Announcements Operation Announcement Auto Voice Announcement Volume Voice Announcement LanguageVoice Announcement Speed Voice Memos Voice Recorder Conversation Recorder Playback Playback RepeatPlayback Repeat Interval CROSS-BAND/ LOCKED-BAND Operation K Type Models only Press Tone + Power on Repeater Hold Repeater IDEntering your Repeater ID Data Terminal Speed Data terminal pinsPacket Operation Data Band PC Port Speed SQC Output Setting Preparation Wireless Operation K Type Models only Control Operation Operation Dtmf Command Transceiver Reset Menu Mode Memory control program MCP-2A Using the MCP-2A SoftwareUsing the MCP-2A software, you can Options PC terminal pins Connecting the PG-5G/ PG-5H interface cablesInstalling the DFK-3D panel kit Installing the Sub-Panel Operation panel Installing the Panel BracketClean and dry the installation location Connect the supplied sub-panel to Installing the Line Filter Connecting the PG-5F extension cableConnecting Using a Single Extension Kit Connecting Using Two Extension Kits Installing the VGS-1 Unit Insert the VGS-1 unit into the connector On the transceiverFrom the remaining cushions, select Cleaning MaintenanceService Service Note Troubleshooting Problem Probable Cause Corrective ActionUP/DWN Specifications GeneralType M4 Type Receiver Transmitter