Manuals / Kodak / Computer Equipment / Scanner

Kodak i800 Series manual Separation roller and tires, Replacing the separation roller

Models: i800 Series

1 83

Download 83 pages 52.33 Kb

Page 58

Separation roller and tires

Separation roller and tires

Replacing the separation roller

This section provides procedures for changing the separation roller and tires.

To replace the separation roller:

1.Open the swing out door.

2.Lift the roller cover.

3.Pull the separation pad holder forward and remove the separation roller.

To install the new separation roller:

4.Pull the separation pad holder forward and put the new separation roller in place.

NOTE: Be sure to line up the slots on the separation roller with the holders.

5.Push the separation roller holder back in place.

6.Lower the roller cover.

7.Close the swing out door.

A-61169 July 2003

5-15

Image 58

Kodak i800 Series manual Separation roller and tires, Replacing the separation roller

Contents

i800 Series Scanners User’s GuideA-61169 Part No. 3E9708 European Union IMPORTANT Equipment shall be installed by qualified personnelDangerous voltage. Disconnect the main power before installation United StatesClass A Japan Class APeoples Republic of China Taiwan1 Introduction A-61169 JulyProduct description Standard features resolutions Standard configurations Transport speedSpeeds and Scanner specifications Top cover Power switchBack of scanner Swing out door∙ The Kodak i800 Series Scanners are designed to meet worldwide 2 Using the Scanner Turning on the scanner To turn on the scannerDocuments must be fed under both feed module tires IMPORTANT Proper alignment of documents is very importantUse the guidelines below when preparing your documents for scanning Acceptable document materials Recommended paper weights Acceptable document sizesMaximum document batch height for automatic feeding Adjusting the side guides on the input trayDownward and upward curl documents Adjusting the output tray 3. Press Start/Resume Scanning documents∙ Press Stop/Pause Loading long documents in the feeder Continuous and manual feedingFeeding thick documents 3 Operator Control Panel Functions Enabling and disabling the scannerDisabled scanner functions Navigating through the functions on the control panel menu Accessing information Lowering the elevator tray Using the Diagnostics Settings menuRunning in count-only mode6. Press Start/Resume 7. Press Stop/Pause Changing the alarm Using the Settingsmenu volumecontrast Changing the display0 to 4. 0 = lightest, 4 = darkest Changing the SCSI termination4. Select Return 3. Press Start/Resume Jogging the transport Programmable key assignments 4 Document Printer and Patch Reader The Document PrinterThe Document Printer can print one line per document To change the print position 1. Open the swing out door 1. Remove the ink cartridge from the box and inner wrappings improper ink flow CAUTION Do not puncture the ink bladder with the paper clipCAUTION Do not touch the ink flow point or you may cause Replacing the ink4. Insert a new, purged ink cartridge 1. Open the swing out door 2. Lift the horizontal transport plate 8. Lower the horizontal transport plate 9. Close the swing out door 7. Re-insert the horizontal belt moduleA-61169 July Setting the printer positionThe Patch Reader Patch typesPatch 2 ⎯ assigns a Level 2 to the current document 1. Set the documents in the elevator tray 2. Open the swing out door Cleaning the paper path 5 MaintenanceUse the green handles when accessing scanner components 4. Place the lower imaging guide on a clean surface Cleaning the upper transport areaFollow the steps below to clean the upper transport area 1. Open the top cover 2. Open the bi-fold door8. Vacuum the area 9. Close the top turn baffle 6. Place the upper imaging guide on a clean surface7. Release the top turn baffle Top turn baffle Exit transport plate11. Lower the exit transport plate 10. Lift and hold the exit transport plate and vacuumA-61169 July Cleaning the vertical transport area6. Vacuum the floor of the lower transport area Cleaning the transport areaFollow the steps below to clean the transport area 7. Raise the vertical transport plate into its original position5. Remove the horizontal belt module 2. Lift the roller cover and vacuum the sensors3. Close the roller cover 4. Lift the horizontal transport plate Roller cover Sensors7. Wipe the upper and lower sensors with a lint-free cloth 8. Reinstall the horizontal belt module6. Vacuum the floor of the horizontal transport area 9. Lower the horizontal transport plateCleaning the printer and patch head Cleaning the imaging guides Maintenance and replacement procedures Replacing the feed module and feed module tires Replacing the feed moduleReplacing the feed the bottom housing with the other hand, pull the upper housing up and4. Remove one core assembly To replace the feed module tires6. Install each new tire by gently stretching it over the core Separation roller and tires Replacing the separation rollerroller tires IMPORTANT Do not overstretch the tire it may tearReplacing the separation Changing the separationReplacing lamps Cleaning the feed module tires and separation roller tires5-18 2. Grasp the green handle of the lamp connector4. Grasp the end of the lamp and slowly pull the lamp straight out A-61169 July5. Position the new lamp in the lamp holder Replacing the imaging To replace the imaging guides guides Customizing the side guides for self- centering feeding NOTE Do not overtighten 3. Use the screwdriver to release the center screw4. Remove the spacer and washer 5-22Changing the output tray side guides 9. Replace the end stop short or tall as required documents are scanned exclusively replacement tires. This kit is used as a replacement when very thinOrdering supplies DescriptionIMPORTANT Use the green handles when accessing scanner components 6 Troubleshooting/MessagesClearing the document path 4. Lift the horizontal transport plate and remove any documents Top cover accessIf there are still lodged documents 3. Open the swing out door 5. Close the horizontal transport plate 6. Close the swing out door11. Close the upper turn roller 12. Close the top cover Clearing the document path - bi-fold door access10. Open the upper turn roller and remove any lodged documents 13. Open the bi-fold door 14. Remove the imaging guides18. Reinstall the imaging guides 19. Close the bi-fold door Operator Control Panel Functions for calibration procedures Message ListingUsing the ISIS Driver for instructions Page Message Document Printer and Patch Reader for procedures Document sensor locationProblem Problem solving chartyou may encounter when using the Kodak i800 Series Scanners Possible SolutionsProblem Possible SolutionsPossible Solutions Problem5, Maintenance Chapter 5, “Cleaning the vertical transport area” ProblemPossible Solutions White lines appear at thePrinted on recycled paper A-61169 7/03 CAT No Eastman Kodak Company EASTMAN KODAK COMPANY Commercial Imaging Rochester, New YorkKodak is a trademark of Eastman Kodak Company Printed in U.S.A