Manuals / Kodak / Computer Equipment / Scanner

Kodak i800 Series manual Set the documents in the elevator tray 2. Open the swing out door

Models: i800 Series

1 83

Download 83 pages 52.33 Kb

Page 43

1.Set the documents in the elevator tray.

Setting the Patch Reader There are 5 patch locations available for patch reading. position

1.Set the documents in the elevator tray.

2.Open the swing out door.

3.Align the patch head with the location of the patch on the documents.

4. Close the swing out door.

NOTE: If patches on the documents change location, repeat the procedure above for the new location.

4-12	A-61169 July 2003

Image 43

Kodak i800 Series manual Set the documents in the elevator tray 2. Open the swing out door

Contents

i800 Series Scanners User’s GuideA-61169 Part No. 3E9708 United States IMPORTANT Equipment shall be installed by qualified personnelDangerous voltage. Disconnect the main power before installation European UnionTaiwan Japan Class APeoples Republic of China Class AA-61169 July 1 IntroductionProduct description Standard features resolutions Standard configurations Transport speedSpeeds and Scanner specifications Swing out door Power switchBack of scanner Top cover∙ The Kodak i800 Series Scanners are designed to meet worldwide Turning on the scanner To turn on the scanner 2 Using the ScannerDocuments must be fed under both feed module tires IMPORTANT Proper alignment of documents is very importantUse the guidelines below when preparing your documents for scanning Acceptable document sizes Acceptable document materials Recommended paper weightsMaximum document batch height for automatic feeding Adjusting the side guides on the input trayDownward and upward curl documents Adjusting the output tray 3. Press Start/Resume Scanning documents∙ Press Stop/Pause Continuous and manual feeding Loading long documents in the feederFeeding thick documents 3 Operator Control Panel Functions the scanner Enabling and disablingDisabled scanner functions Navigating through the functions on the control panel menu Using the Diagnostics Settings menu Accessing information Lowering the elevator traymode Running in count-only6. Press Start/Resume 7. Press Stop/Pause volume Using the Settingsmenu Changing the alarmcontrast Changing the display0 to 4. 0 = lightest, 4 = darkest termination Changing the SCSI4. Select Return 3. Press Start/Resume Jogging the transport Programmable key assignments The Document Printer 4 Document Printer and Patch ReaderThe Document Printer can print one line per document To change the print position 1. Open the swing out door 1. Remove the ink cartridge from the box and inner wrappings Replacing the ink CAUTION Do not puncture the ink bladder with the paper clipCAUTION Do not touch the ink flow point or you may cause improper ink flow4. Insert a new, purged ink cartridge 1. Open the swing out door 2. Lift the horizontal transport plate 8. Lower the horizontal transport plate 9. Close the swing out door 7. Re-insert the horizontal belt moduleA-61169 July position Setting the printerPatch types The Patch ReaderPatch 2 ⎯ assigns a Level 2 to the current document 1. Set the documents in the elevator tray 2. Open the swing out door Cleaning the paper path 5 MaintenanceUse the green handles when accessing scanner components 1. Open the top cover 2. Open the bi-fold door Cleaning the upper transport areaFollow the steps below to clean the upper transport area 4. Place the lower imaging guide on a clean surfaceTop turn baffle Exit transport plate 6. Place the upper imaging guide on a clean surface7. Release the top turn baffle 8. Vacuum the area 9. Close the top turn baffle11. Lower the exit transport plate 10. Lift and hold the exit transport plate and vacuumA-61169 July transport area Cleaning the vertical7. Raise the vertical transport plate into its original position Cleaning the transport areaFollow the steps below to clean the transport area 6. Vacuum the floor of the lower transport areaRoller cover Sensors 2. Lift the roller cover and vacuum the sensors3. Close the roller cover 4. Lift the horizontal transport plate 5. Remove the horizontal belt module9. Lower the horizontal transport plate 8. Reinstall the horizontal belt module6. Vacuum the floor of the horizontal transport area 7. Wipe the upper and lower sensors with a lint-free clothCleaning the printer and patch head Cleaning the imaging guides Maintenance and replacement procedures Replacing the feed module Replacing the feed module and feed module tiresTo replace the feed module tires the bottom housing with the other hand, pull the upper housing up and4. Remove one core assembly Replacing the feed6. Install each new tire by gently stretching it over the core Replacing the separation roller Separation roller and tiresChanging the separation IMPORTANT Do not overstretch the tire it may tearReplacing the separation roller tiresCleaning the feed module tires and separation roller tires Replacing lampsA-61169 July 2. Grasp the green handle of the lamp connector4. Grasp the end of the lamp and slowly pull the lamp straight out 5-185. Position the new lamp in the lamp holder Replacing the imaging To replace the imaging guides guides Customizing the side guides for self- centering feeding 5-22 3. Use the screwdriver to release the center screw4. Remove the spacer and washer NOTE Do not overtightenChanging the output tray side guides 9. Replace the end stop short or tall as required Description replacement tires. This kit is used as a replacement when very thinOrdering supplies documents are scanned exclusivelyIMPORTANT Use the green handles when accessing scanner components 6 Troubleshooting/MessagesClearing the document path 5. Close the horizontal transport plate 6. Close the swing out door Top cover accessIf there are still lodged documents 3. Open the swing out door 4. Lift the horizontal transport plate and remove any documents13. Open the bi-fold door 14. Remove the imaging guides Clearing the document path - bi-fold door access10. Open the upper turn roller and remove any lodged documents 11. Close the upper turn roller 12. Close the top cover18. Reinstall the imaging guides 19. Close the bi-fold door Message Listing Operator Control Panel Functions for calibration proceduresUsing the ISIS Driver for instructions Page Message Document Printer and Patch Reader for procedures location Document sensorPossible Solutions Problem solving chartyou may encounter when using the Kodak i800 Series Scanners ProblemPossible Solutions ProblemPossible Solutions Problem5, Maintenance White lines appear at the ProblemPossible Solutions Chapter 5, “Cleaning the vertical transport area”Printed in U.S.A EASTMAN KODAK COMPANY Commercial Imaging Rochester, New YorkKodak is a trademark of Eastman Kodak Company Printed on recycled paper A-61169 7/03 CAT No Eastman Kodak Company