Manuals / Kodak / Computer Equipment / Scanner

Kodak i800 Series manual Position the new lamp in the lamp holder

Models: i800 Series

1 83

Download 83 pages 52.33 Kb

Page 62

5. Position the new lamp in the lamp holder.

5. Position the new lamp in the lamp holder.

IMPORTANT: Make sure that the clear surface of the lamp is positioned facing the imaging guides. (NOTE: The imaging guides are not installed in the illustration above.) Replace one lamp at a time to ensure the correct connector is inserted with each lamp; otherwise lamps may not function properly.

6.Push firmly on the end of the lamp to seat the lamp into the socket on the other end.

7.Replace the green lamp connector and push it in firmly so the connector is fully seated.

8.Close the bi-fold door.

9.Allow 10 minutes for the lamps to warm up.

10.Calibrate the scanner. See Chapter 3, Operator Control Panel Functions for procedures.

A-61169 July 2003

5-19

Image 62

Kodak i800 Series manual Position the new lamp in the lamp holder

Contents

A-61169 Part No. 3E9708 User’s Guidei800 Series Scanners European Union IMPORTANT Equipment shall be installed by qualified personnelDangerous voltage. Disconnect the main power before installation United StatesClass A Japan Class APeoples Republic of China Taiwan1 Introduction A-61169 JulyProduct description Standard features Speeds and Standard configurations Transport speedresolutions Scanner specifications Top cover Power switchBack of scanner Swing out door∙ The Kodak i800 Series Scanners are designed to meet worldwide 2 Using the Scanner Turning on the scanner To turn on the scannerUse the guidelines below when preparing your documents for scanning IMPORTANT Proper alignment of documents is very importantDocuments must be fed under both feed module tires Acceptable document materials Recommended paper weights Acceptable document sizesDownward and upward curl documents Adjusting the side guides on the input trayMaximum document batch height for automatic feeding Adjusting the output tray ∙ Press Stop/Pause Scanning documents3. Press Start/Resume Loading long documents in the feeder Continuous and manual feedingFeeding thick documents 3 Operator Control Panel Functions Enabling and disabling the scannerDisabled scanner functions Navigating through the functions on the control panel menu Accessing information Lowering the elevator tray Using the Diagnostics Settings menuRunning in count-only mode6. Press Start/Resume 7. Press Stop/Pause Changing the alarm Using the Settingsmenu volume0 to 4. 0 = lightest, 4 = darkest Changing the displaycontrast Changing the SCSI termination4. Select Return 3. Press Start/Resume Jogging the transport Programmable key assignments 4 Document Printer and Patch Reader The Document PrinterThe Document Printer can print one line per document To change the print position 1. Open the swing out door 1. Remove the ink cartridge from the box and inner wrappings improper ink flow CAUTION Do not puncture the ink bladder with the paper clipCAUTION Do not touch the ink flow point or you may cause Replacing the ink4. Insert a new, purged ink cartridge 1. Open the swing out door 2. Lift the horizontal transport plate A-61169 July 7. Re-insert the horizontal belt module8. Lower the horizontal transport plate 9. Close the swing out door Setting the printer positionThe Patch Reader Patch typesPatch 2 ⎯ assigns a Level 2 to the current document 1. Set the documents in the elevator tray 2. Open the swing out door Use the green handles when accessing scanner components 5 MaintenanceCleaning the paper path 4. Place the lower imaging guide on a clean surface Cleaning the upper transport areaFollow the steps below to clean the upper transport area 1. Open the top cover 2. Open the bi-fold door8. Vacuum the area 9. Close the top turn baffle 6. Place the upper imaging guide on a clean surface7. Release the top turn baffle Top turn baffle Exit transport plateA-61169 July 10. Lift and hold the exit transport plate and vacuum11. Lower the exit transport plate Cleaning the vertical transport area6. Vacuum the floor of the lower transport area Cleaning the transport areaFollow the steps below to clean the transport area 7. Raise the vertical transport plate into its original position5. Remove the horizontal belt module 2. Lift the roller cover and vacuum the sensors3. Close the roller cover 4. Lift the horizontal transport plate Roller cover Sensors7. Wipe the upper and lower sensors with a lint-free cloth 8. Reinstall the horizontal belt module6. Vacuum the floor of the horizontal transport area 9. Lower the horizontal transport plateCleaning the printer and patch head Cleaning the imaging guides Maintenance and replacement procedures Replacing the feed module and feed module tires Replacing the feed moduleReplacing the feed the bottom housing with the other hand, pull the upper housing up and4. Remove one core assembly To replace the feed module tires6. Install each new tire by gently stretching it over the core Separation roller and tires Replacing the separation rollerroller tires IMPORTANT Do not overstretch the tire it may tearReplacing the separation Changing the separationReplacing lamps Cleaning the feed module tires and separation roller tires5-18 2. Grasp the green handle of the lamp connector4. Grasp the end of the lamp and slowly pull the lamp straight out A-61169 July5. Position the new lamp in the lamp holder Replacing the imaging To replace the imaging guides guides Customizing the side guides for self- centering feeding NOTE Do not overtighten 3. Use the screwdriver to release the center screw4. Remove the spacer and washer 5-22Changing the output tray side guides 9. Replace the end stop short or tall as required documents are scanned exclusively replacement tires. This kit is used as a replacement when very thinOrdering supplies DescriptionClearing the document path 6 Troubleshooting/MessagesIMPORTANT Use the green handles when accessing scanner components 4. Lift the horizontal transport plate and remove any documents Top cover accessIf there are still lodged documents 3. Open the swing out door 5. Close the horizontal transport plate 6. Close the swing out door11. Close the upper turn roller 12. Close the top cover Clearing the document path - bi-fold door access10. Open the upper turn roller and remove any lodged documents 13. Open the bi-fold door 14. Remove the imaging guides18. Reinstall the imaging guides 19. Close the bi-fold door Operator Control Panel Functions for calibration procedures Message ListingUsing the ISIS Driver for instructions Page Message Document Printer and Patch Reader for procedures Document sensor locationProblem Problem solving chartyou may encounter when using the Kodak i800 Series Scanners Possible SolutionsProblem Possible Solutions5, Maintenance ProblemPossible Solutions Chapter 5, “Cleaning the vertical transport area” ProblemPossible Solutions White lines appear at thePrinted on recycled paper A-61169 7/03 CAT No Eastman Kodak Company EASTMAN KODAK COMPANY Commercial Imaging Rochester, New YorkKodak is a trademark of Eastman Kodak Company Printed in U.S.A