Manuals / Kodak / Computer Equipment / Scanner

Kodak i800 Series manual Cleaning the printer and patch head

Models: i800 Series

1 83

Download 83 pages 52.33 Kb

Page 52

Cleaning the printer and patch head

Cleaning the printer and patch head

A-61169 July 2003

Follow the steps below to clean the Document Printer 1 and Patch Reader head. Complete instructions for the Document Printer and Patch Reader can be found in Chapter 4.

1.Remove the Document Printer head and clean it with a dry, lint-free cloth.

White clip

2. Reinstall the Document Printer head in the desired position.

IMPORTANT: Be sure the cable is always kept in place by the white clip to prevent the cable from interfering with the imaging path.

3. Remove the patch head and clean it with a dry, lint-free cloth.

4.Replace the patch head in the desired position.

5.Close the swing out door.

5-9

Image 52

Kodak i800 Series manual Cleaning the printer and patch head

Contents

i800 Series Scanners User’s GuideA-61169 Part No. 3E9708 IMPORTANT Equipment shall be installed by qualified personnel Dangerous voltage. Disconnect the main power before installationEuropean Union United StatesJapan Class A Peoples Republic of ChinaClass A Taiwan1 Introduction A-61169 JulyProduct description Standard features resolutions Standard configurations Transport speedSpeeds and Scanner specifications Power switch Back of scannerTop cover Swing out door∙ The Kodak i800 Series Scanners are designed to meet worldwide 2 Using the Scanner Turning on the scanner To turn on the scannerDocuments must be fed under both feed module tires IMPORTANT Proper alignment of documents is very importantUse the guidelines below when preparing your documents for scanning Acceptable document materials Recommended paper weights Acceptable document sizesMaximum document batch height for automatic feeding Adjusting the side guides on the input trayDownward and upward curl documents Adjusting the output tray 3. Press Start/Resume Scanning documents∙ Press Stop/Pause Loading long documents in the feeder Continuous and manual feedingFeeding thick documents 3 Operator Control Panel Functions Enabling and disabling the scannerDisabled scanner functions Navigating through the functions on the control panel menu Accessing information Lowering the elevator tray Using the Diagnostics Settings menuRunning in count-only mode6. Press Start/Resume 7. Press Stop/Pause Using the Settings menuChanging the alarm volumecontrast Changing the display0 to 4. 0 = lightest, 4 = darkest Changing the SCSI termination4. Select Return 3. Press Start/Resume Jogging the transport Programmable key assignments 4 Document Printer and Patch Reader The Document PrinterThe Document Printer can print one line per document To change the print position 1. Open the swing out door 1. Remove the ink cartridge from the box and inner wrappings CAUTION Do not puncture the ink bladder with the paper clip CAUTION Do not touch the ink flow point or you may causeimproper ink flow Replacing the ink4. Insert a new, purged ink cartridge 1. Open the swing out door 2. Lift the horizontal transport plate 8. Lower the horizontal transport plate 9. Close the swing out door 7. Re-insert the horizontal belt moduleA-61169 July Setting the printer positionThe Patch Reader Patch typesPatch 2 ⎯ assigns a Level 2 to the current document 1. Set the documents in the elevator tray 2. Open the swing out door Cleaning the paper path 5 MaintenanceUse the green handles when accessing scanner components Cleaning the upper transport area Follow the steps below to clean the upper transport area4. Place the lower imaging guide on a clean surface 1. Open the top cover 2. Open the bi-fold door6. Place the upper imaging guide on a clean surface 7. Release the top turn baffle8. Vacuum the area 9. Close the top turn baffle Top turn baffle Exit transport plate11. Lower the exit transport plate 10. Lift and hold the exit transport plate and vacuumA-61169 July Cleaning the vertical transport areaCleaning the transport area Follow the steps below to clean the transport area6. Vacuum the floor of the lower transport area 7. Raise the vertical transport plate into its original position2. Lift the roller cover and vacuum the sensors 3. Close the roller cover 4. Lift the horizontal transport plate5. Remove the horizontal belt module Roller cover Sensors8. Reinstall the horizontal belt module 6. Vacuum the floor of the horizontal transport area7. Wipe the upper and lower sensors with a lint-free cloth 9. Lower the horizontal transport plateCleaning the printer and patch head Cleaning the imaging guides Maintenance and replacement procedures Replacing the feed module and feed module tires Replacing the feed modulethe bottom housing with the other hand, pull the upper housing up and 4. Remove one core assemblyReplacing the feed To replace the feed module tires6. Install each new tire by gently stretching it over the core Separation roller and tires Replacing the separation rollerIMPORTANT Do not overstretch the tire it may tear Replacing the separationroller tires Changing the separationReplacing lamps Cleaning the feed module tires and separation roller tires2. Grasp the green handle of the lamp connector 4. Grasp the end of the lamp and slowly pull the lamp straight out5-18 A-61169 July5. Position the new lamp in the lamp holder Replacing the imaging To replace the imaging guides guides Customizing the side guides for self- centering feeding 3. Use the screwdriver to release the center screw 4. Remove the spacer and washerNOTE Do not overtighten 5-22Changing the output tray side guides 9. Replace the end stop short or tall as required replacement tires. This kit is used as a replacement when very thin Ordering suppliesdocuments are scanned exclusively DescriptionIMPORTANT Use the green handles when accessing scanner components 6 Troubleshooting/MessagesClearing the document path Top cover access If there are still lodged documents 3. Open the swing out door4. Lift the horizontal transport plate and remove any documents 5. Close the horizontal transport plate 6. Close the swing out doorClearing the document path - bi-fold door access 10. Open the upper turn roller and remove any lodged documents11. Close the upper turn roller 12. Close the top cover 13. Open the bi-fold door 14. Remove the imaging guides18. Reinstall the imaging guides 19. Close the bi-fold door Operator Control Panel Functions for calibration procedures Message ListingUsing the ISIS Driver for instructions Page Message Document Printer and Patch Reader for procedures Document sensor locationProblem solving chart you may encounter when using the Kodak i800 Series ScannersProblem Possible SolutionsProblem Possible SolutionsPossible Solutions Problem5, Maintenance Problem Possible SolutionsChapter 5, “Cleaning the vertical transport area” White lines appear at theEASTMAN KODAK COMPANY Commercial Imaging Rochester, New York Kodak is a trademark of Eastman Kodak CompanyPrinted on recycled paper A-61169 7/03 CAT No Eastman Kodak Company Printed in U.S.A