Manuals / Kodak / Computer Equipment / Scanner

Kodak i800 Series manual Grasp the green handle of the lamp connector, 5-18, A-61169 July

Models: i800 Series

1 83

Download 83 pages 52.33 Kb

Page 61

2. Grasp the green handle of the lamp connector.

2. Grasp the green handle of the lamp connector.

3.Slightly raise the edge of the black holder and remove the lamp connector.

4.Grasp the end of the lamp and slowly pull the lamp straight out.

NOTE: Like most fluorescent lamps, these lamps contain a small amount of mercury and should be disposed of in accordance with local regulations.

5-18	A-61169 July 2003

Image 61

Kodak i800 Series manual Grasp the green handle of the lamp connector, 5-18, A-61169 July

Contents

i800 Series Scanners User’s GuideA-61169 Part No. 3E9708 Dangerous voltage. Disconnect the main power before installation IMPORTANT Equipment shall be installed by qualified personnelEuropean Union United StatesPeoples Republic of China Japan Class AClass A TaiwanA-61169 July 1 IntroductionProduct description Standard features resolutions Standard configurations Transport speedSpeeds and Scanner specifications Back of scanner Power switchTop cover Swing out door∙ The Kodak i800 Series Scanners are designed to meet worldwide Turning on the scanner To turn on the scanner 2 Using the ScannerDocuments must be fed under both feed module tires IMPORTANT Proper alignment of documents is very importantUse the guidelines below when preparing your documents for scanning Acceptable document sizes Acceptable document materials Recommended paper weightsMaximum document batch height for automatic feeding Adjusting the side guides on the input trayDownward and upward curl documents Adjusting the output tray 3. Press Start/Resume Scanning documents∙ Press Stop/Pause Continuous and manual feeding Loading long documents in the feederFeeding thick documents 3 Operator Control Panel Functions the scanner Enabling and disablingDisabled scanner functions Navigating through the functions on the control panel menu Using the Diagnostics Settings menu Accessing information Lowering the elevator traymode Running in count-only6. Press Start/Resume 7. Press Stop/Pause menu Using the SettingsChanging the alarm volumecontrast Changing the display0 to 4. 0 = lightest, 4 = darkest termination Changing the SCSI4. Select Return 3. Press Start/Resume Jogging the transport Programmable key assignments The Document Printer 4 Document Printer and Patch ReaderThe Document Printer can print one line per document To change the print position 1. Open the swing out door 1. Remove the ink cartridge from the box and inner wrappings CAUTION Do not touch the ink flow point or you may cause CAUTION Do not puncture the ink bladder with the paper clipimproper ink flow Replacing the ink4. Insert a new, purged ink cartridge 1. Open the swing out door 2. Lift the horizontal transport plate 8. Lower the horizontal transport plate 9. Close the swing out door 7. Re-insert the horizontal belt moduleA-61169 July position Setting the printerPatch types The Patch ReaderPatch 2 ⎯ assigns a Level 2 to the current document 1. Set the documents in the elevator tray 2. Open the swing out door Cleaning the paper path 5 MaintenanceUse the green handles when accessing scanner components Follow the steps below to clean the upper transport area Cleaning the upper transport area4. Place the lower imaging guide on a clean surface 1. Open the top cover 2. Open the bi-fold door7. Release the top turn baffle 6. Place the upper imaging guide on a clean surface8. Vacuum the area 9. Close the top turn baffle Top turn baffle Exit transport plate11. Lower the exit transport plate 10. Lift and hold the exit transport plate and vacuumA-61169 July transport area Cleaning the verticalFollow the steps below to clean the transport area Cleaning the transport area6. Vacuum the floor of the lower transport area 7. Raise the vertical transport plate into its original position3. Close the roller cover 4. Lift the horizontal transport plate 2. Lift the roller cover and vacuum the sensors5. Remove the horizontal belt module Roller cover Sensors6. Vacuum the floor of the horizontal transport area 8. Reinstall the horizontal belt module7. Wipe the upper and lower sensors with a lint-free cloth 9. Lower the horizontal transport plateCleaning the printer and patch head Cleaning the imaging guides Maintenance and replacement procedures Replacing the feed module Replacing the feed module and feed module tires4. Remove one core assembly the bottom housing with the other hand, pull the upper housing up andReplacing the feed To replace the feed module tires6. Install each new tire by gently stretching it over the core Replacing the separation roller Separation roller and tiresReplacing the separation IMPORTANT Do not overstretch the tire it may tearroller tires Changing the separationCleaning the feed module tires and separation roller tires Replacing lamps4. Grasp the end of the lamp and slowly pull the lamp straight out 2. Grasp the green handle of the lamp connector5-18 A-61169 July5. Position the new lamp in the lamp holder Replacing the imaging To replace the imaging guides guides Customizing the side guides for self- centering feeding 4. Remove the spacer and washer 3. Use the screwdriver to release the center screwNOTE Do not overtighten 5-22Changing the output tray side guides 9. Replace the end stop short or tall as required Ordering supplies replacement tires. This kit is used as a replacement when very thindocuments are scanned exclusively DescriptionIMPORTANT Use the green handles when accessing scanner components 6 Troubleshooting/MessagesClearing the document path If there are still lodged documents 3. Open the swing out door Top cover access4. Lift the horizontal transport plate and remove any documents 5. Close the horizontal transport plate 6. Close the swing out door10. Open the upper turn roller and remove any lodged documents Clearing the document path - bi-fold door access11. Close the upper turn roller 12. Close the top cover 13. Open the bi-fold door 14. Remove the imaging guides18. Reinstall the imaging guides 19. Close the bi-fold door Message Listing Operator Control Panel Functions for calibration proceduresUsing the ISIS Driver for instructions Page Message Document Printer and Patch Reader for procedures location Document sensoryou may encounter when using the Kodak i800 Series Scanners Problem solving chartProblem Possible SolutionsPossible Solutions ProblemPossible Solutions Problem5, Maintenance Possible Solutions ProblemChapter 5, “Cleaning the vertical transport area” White lines appear at theKodak is a trademark of Eastman Kodak Company EASTMAN KODAK COMPANY Commercial Imaging Rochester, New YorkPrinted on recycled paper A-61169 7/03 CAT No Eastman Kodak Company Printed in U.S.A