9. Basic functions
9.3Run Command setting
Run via the Run and STOP/RST key
| Group |
|
| LED Display |
|
| Parameter Name |
|
| Set |
|
| Min/Max |
|
| Factory |
|
| Unit |
|
|
|
|
|
|
|
| Value |
|
| Range |
|
| Defaults |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Drive |
|
| drv |
|
| [Drive mode] |
|
| 0 |
| 0/3 |
| 1 |
|
|
|
| ||
| group |
|
|
|
| (Run/Stop mode) |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| drC |
|
| [Direction of motor rotation | - |
|
| F/r |
|
| F |
|
|
|
| ||
|
|
|
|
|
| select] |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set drv – [Drive mode] to 0.
Motor starts to accelerate by pressing the Run key while run frequency is set. Motor decelerates to stop by pressing the STOP/RST key.
Selecting rotation direction is available at drC - [Direction of motor rotation select] when run command is issued via Run key on keypad.
drC | [Direction of motor | F | Forward |
| rotation select] |
|
|
| R | Reverse | |
|
|
|
|
FX : Counter clockwise
Run command setting 1 via FX and RX terminals
| Group |
|
| LED Display |
|
| Parameter Name |
|
| Set |
|
| Min/Max |
|
| Factory |
|
| Unit |
|
|
|
|
|
|
|
| Value |
|
| Range |
|
| Defaults |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Drive |
|
| drv |
|
| [Drive mode] |
|
| 1 |
| 0/3 |
| 1 |
|
|
|
| ||
| group |
|
|
|
| (Run/Stop mode) |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| I/O group |
|
| I20 |
|
| 0 |
| 0/24 |
| 0 |
|
|
|
| |||||
|
|
|
|
|
| P1 define] |
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| I21 |
|
| 1 |
| 0/24 |
| 1 |
|
|
|
| |||||
|
|
|
|
|
| P2 define] |
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set drv – [Drive mode] to 1.
Set I20 and I21 to 0 and 1 to use P1 and P2 as FX and RX terminals. “FX” is Forward run command and “RX” Reverse run.
Operation will stop when both FX and RX terminals are turned ON or OFF.
Frequency |
|
FX |
|
RX |
|