7. Function list
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Function group 2 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LED |
|
| Parameter |
|
| Min/Max |
|
| Description |
|
| Factory |
|
| Adjustable |
|
| Page |
|
| display |
|
| name |
|
| range |
|
|
|
| defaults |
|
| during run |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| H16 |
|
| [Skip |
|
|
|
|
|
|
| 35.0 |
|
| X |
|
|
|
| |
|
|
|
| frequency high |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| limit 3] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| H17 |
|
|
| 1/100 [%] |
| Set the speed reference value to form a curve |
| 40 |
|
| X |
|
| ||||||
|
|
|
| accel/decel |
|
|
|
|
| at the start during accel/decel. If it is set higher, |
|
|
|
|
|
|
|
|
|
|
|
|
|
| start side |
|
|
|
|
| linear zone gets smaller. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| H18 |
|
|
| 1/100 [%] |
| Set the speed reference value to form a curve |
| 40 |
|
| X |
|
|
|
| ||||
|
|
|
| accel/decel |
|
|
|
|
| at the end during accel/decel. If it is set higher, |
|
|
|
|
|
|
|
|
|
|
|
|
|
| end side |
|
|
|
|
| linear zone gets smaller. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| H19 |
|
| [Output phase |
| 0/1 |
|
| Inverter turns off the output when the |
| 0 |
|
| O |
|
| ||||
|
|
|
| loss protection |
|
|
|
|
| phase of the inverter output (U, V, W) is not |
|
|
|
|
|
|
|
|
|
|
|
|
|
| select] |
|
|
|
|
| properly connected. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| H20 |
|
| [Power On |
| 0/1 |
|
| This parameter is activated when drv is set |
| 0 |
|
| O |
|
| ||||
|
|
|
| Start select] |
|
|
|
|
| to 1 or 2 (Run/Stop via Control terminal). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Motor starts acceleration after AC power |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| is applied while FX or RX terminal is ON. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| H21 |
|
| [Restart after |
| 0/1 |
|
| This parameter is active when drv is set to |
| 0 |
|
| O |
|
|
|
| ||
|
|
|
| fault reset] |
|
|
|
|
| 1 or 2 (Run/Stop via Control terminal). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Motor accelerates after the fault condition |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| is reset while the FX or RX terminal is ON. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1) Set H10 to 1 to be displayed.
# H17, 18 is used when F2, F3 is set to 1