S2 Gate Drive Fail, Internal Comm Fail | Liebert 100-1000A instruction

Event Message Help Text

S2 GATE DRIVE FAIL

Source 1 Gate Drive Failure.

The gate drive module for an SCR for Source 2 has failed. This module is contained on the left side gate driver board.

Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the Liebert STS2 system from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.

Contact Liebert Services for technical support at 1-800-LIEBERT (800-543-2378).

This event was written to the Event Log, if so configured.

The alarm has triggered a message to be sent to the modem, if so configured.

If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type CA and press RETURN on your keyboard.

INTERNAL COMM FAIL

Internal CAN Communications Failed.

Communications have failed in the CAN bus between the control board and the touch screen control.

Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the Liebert STS2 system from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.

Contact Liebert Services for technical support at 1-800-LIEBERT (800-543-2378).

This event was written to the Event Log, if so configured.

The alarm has triggered a message to be sent to the modem, if so configured.

If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type CA and press RETURN on your keyboard.

EXTERNAL COMM FAIL

External Communications Failed.

Communications have failed between the control board and the CAN options.

Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the unit from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.

Contact Liebert Services for technical support at 1-800-LIEBERT (800-543-2378).

This event was written to the Event Log, if so configured.

The alarm has triggered a message to be sent to the modem, if so configured.

If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type CA and press RETURN on your keyboard.

123

Image 131

Liebert 100-1000A user manual S2 Gate Drive Fail, Internal Comm Fail

Contents

Liebert STS2 Page Table of Contents Theory of Operation Alarm and Faults Liebert STS2 Touch Screen Display Communication Interfaces Event Message Help Text 17.0 Maintenance Specifications Figures Tables Important Safety Instructions Overview of Manual Safety Precautions Unpacking and Inspections External InspectionsUnloading and Handling Unit Preparation Internal InspectionsHandling Considerations Operating Environment Recommended Minimum Service ClearancesOperating Temperature Range 0 to 40C 32 to 104F Heat Output Recommended derating for high altitude operation Altitude Locating the Liebert STS2 Leveling of the Static Switch Without AnchoringLeveling and Anchoring the Static Switch Using Floor Stand Leveling and Anchoring the Unit to the Floor Power and Control Wiring Input And Output Power Connections Rating Max. number and size Input Junction Box Installation-OptionalInput/output conduit plate specifications Switch Rating Power and Ground Lug Wire Range Input junction box dimensionsInput junction box terminal wire size range Length Width Height Switch Rating Inches mm CB4 CB3 Control Wiring ConnectionsSystem Grounding Source MICB1 MICB2 Isolation Transformer Remote source selection terminal block Remote Source Selection WiringPower Supply Terminal block 1 and terminal block 2 wire connections Programmable relay board pinout Programmable Relay BoardOptimized Transfer Options Liebert IntelliSlot SNMP/Web/Modbus 485 Card Input Contact Isolator BoardComms Board Redundant Output Breaker Key Lockout SwitchLED Display Remote Source Selection Seismic Floor Stand Input Junction Boxes and CablesSeismic Floor Anchors Detail a Installation Drawings Rev PS211800 Rev PS211101 Rev PS211401 PS211801 Liebert STS2 Seismic anchor STS2 System Seismic ANCHORING, Figure Front ONE-LINE Diagram Rev Section A-A ONE-LINE Diagram PS212401 Single output Drawing 800 1000 amp Liebert STS2 withBreaker PS212801 ABB Liebert STS2 non-automatic circuit breaker schedule See Option Location Detail Control connection location diagram 100 600 amp Liebert STS2 Front View with Front Door Removed Option Location Detail Control Wiring See Note J74 J71J72 J73 Table J51 Control wiring for the input contact isolator board option 02-810015-XX No customer ConnectionNo customer Connection DB-9 TXD RXD GND Control wiring for the RS-232 port Input Junction BOX Mimic Description Symbol Installation drawing, seismic floor stand 100-250A Seismic floor stand 100-250A Installation drawing Stand 100-250A Installation drawing, seismic floor PS215003 Rev Height Table Hardware Torque ChartDrawing, seismic floor stand 400-600A Seismic floor stand 400-600A PS216001 Rev PS216002 Rev PS216003 Rev Installation drawing, seismic floor stand 800-1000A Seismic floor stand 800-1000A Right Side View Front Right Isometric View Rear Right Isometric View View Side ViewRight Front View Redundancy System DescriptionIntroduction to Liebert STS2 Operations Modes of Operation Bypass Operator Controls Theory of Operation General Description 7 On/Off Sequence Emergency TransferLoad Current Transfer Inhibit SCR Failure Firmware Detailed Component DescriptionControls Operator Interface Hardware Logic Modules Audible AlarmCircuit Breakers SCRs Operating Instructions for the Touch Screen Interface Normal System Startup Source transfer screen Manual Transfer / Preferred Source Selection To manually select the preferred source Maintenance BypassEnabling Remote Source Selection Touch Screen Viewing Slot for the Source 1 Gate Drive Board Viewing Slot for the Source 2 Gate Drive Board To return to normal mode Bypass Procedures for SourceTo bypass the switch for Source Normal System Shutdown Shutdown in Static Transfer Switch ModeShutdown in Maintenance Bypass Mode Event Mask Alarm and Faults History Log Event and History LogsEvent Log List of Messages Alarm Notes Event messages Alarm Message Description/Cause Action See Configuring the Input Contact Isolator Settings on Communication Interfaces Using the RS-232 Port Keys Function Connecting and Using a TerminalTerminal commands Item Parameter Configuring the Liebert STS2 via the TerminalGroups Parameter Value types Group settings and valuesValue Parameter Event Mask User Comms Options Setting Bitpacked Options with the TerminalOptions1 Hex Critical Option EnablingNon-Critical Option Enabling Binary-hexadecimal conversions Putting the Terminal Command Together Examples of Event Mask Settings Setting Event Masks with the Terminal Liebert STS2 Touch Screen Display Display Overview Backspace Menu Overview Changes disabled Changes enabled Using the Optional Key Lockout SwitchUsing the Password To set or reset the password Event Display Configuration MenuMimic Display Event Controls To set the event masks User SettingsTo access the User Settings dialog box Source Set Points User settings dialog box Sepoint parameters To configure the setpoints for each sourceButton Range Default Comments Liebert STS2 Touch Screen Display Option buttons System SettingsTo access the System Settings menu Comm Options To configure the modem Configuring the Modem Configuring Pager Support To configure the Input Contact Isolator relays Configuring the Input Contact Isolator Settings Relay Setting Definition Configuring the Programmable Relay Board SettingsStandard settings for programmable relays Configuring the Liebert IntelliSlot SNMP/Web/Modbus 485 Card Dual Output Breaker Liebert SiteScan ConfigurationSaving Your Communications Configurations System Options Wye Output Transformer Pole Transfer SwitchSystem ID Shunt To use the Event Log Logs13.11.1Event Log 13.11.2History Log Source Transfers Startup ProcedureBypass Procedure Cleaning the LCD Touch Screen Front Panel Controls LEDs and Buttons and Key Lockout SwitchOperating the Liebert STS2 LED Display Cause. See 12.0 Communication Interfaces for PC terminal LED and Push Button DescriptionLED and push button description Description Action Event Controls Key Lockout Switch Normal System Startup Operations Manual Transfer / Preferred Source Selection Maintenance Bypass 109 Normal System Shutdown When the Liebert STS2 is operating on bypass Input/Output Voltage System ConfigurationSpecifications Frequency Response Time GroundingElectrical Requirements Input Surge Suppression Cooling System ComponentsFrame and Enclosure Casters, Leveling and Seismic Anchoring Color Graphical Display or LED Display AccessCable Entrance Doors MTA plug pinout Pin Signal Name Function / Comments15.2.9 RS-232 Port Terminal Port Connections Fuseless Design RS-232 settingsParameter Setting 15.2.11 RS-232 Interface Parameters S2 SCR Short Event Message Help TextKey S1 SCR Short S2 SCR Open 119 120 S1 SCR Sense Fail S1 Volt Sense FailS2 Volt Sense Fail S1 Gate Drive Fail S2 SCR Sense FailS1 Curr Sense Fail S2 Curr Sense Fail S2 Gate Drive Fail Heat Sink Overtemp S1 OV S1 UVS1 UV RMS S2 UV S1 OF/UFS1 Fail S2 UF/OF S2 UV RMSS2 OV S2 Fail S2 I-PEAK S1 I-PEAK 130 CB5 S1 BYP Closed 132 133 134 135 136 137 Changing the Air Filter Testing the Liebert STS2Maintenance Proper Tightening of Nuts and Bolts Support Information Channel Programmable Relay Board Settings Record Channel PRB Notes Input Contact Isolator Settings Record Page Care Ne tIs t Twor k