26
|
| (335 MM) | (335 MM) | (396 MM) | (335 MM) | (335 MM) | REAR FLOOR |
|
|
|
|
|
|
|
| |
SEE | NOTE (7) | 13.2" | 13.2" | 15.6" | 13.2" | 13.2" | BRACKET | (2) |
|
|
|
|
|
|
| |
FOR SPACING |
|
|
|
| BACK | WALL | SEE NOTE |
|
|
|
|
|
|
| ||
|
|
|
| FOR SPACING |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| REAR | CABINET |
|
|
|
|
| |
|
|
|
|
|
|
|
|
| BASE | BRACKET | BACK |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| WALL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| APPROX | 1/2" |
|
|
|
|
|
|
|
|
|
|
|
| FLOOR | LINE | REAR F LOOR |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| BRACKET |
|
|
|
|
| (832 MM) |
|
|
|
|
|
|
|
|
| FLOOR | ANCHOR |
|
|
|
|
|
|
|
|
|
|
|
|
|
| HARDWARE |
|
|
|
| ||
| 32.75" |
|
|
|
|
|
|
|
|
| (NOT SUPPLIED ) |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| FRONT |
|
|
|
| FIGURE | 2 |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| WALL |
|
|
|
|
|
|
|
|
|
| FRONT | DOOR | FRONT | CABINET | |
|
|
|
|
|
|
|
|
|
|
| OF CABINET | BASE | BRACKET |
| ||
| SIDE |
|
|
|
|
|
|
|
|
|
| SUPPLIED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| HARDWARE |
|
|
|
|
| FRONT | FLOOR | (310 MM) | (289 MM) |
| (817MM) |
| (144 MM) |
|
| FLOOR ANCHOR |
|
|
| ||
| BRACKET | 12.2" | 11.4" |
| 32.2" |
| 5.7" |
|
|
| HARDWARE |
|
|
|
| |
|
| (107 MM) |
|
|
|
|
| NOT SUPPLIED |
|
|
|
| ||||
|
| (107 MM) | (107 MM) |
|
|
| (107 MM) |
|
|
|
|
|
|
|
| |
|
| 4.2" | 4.2" | 4.2" |
|
|
| 4.2" |
|
|
|
|
|
| FLOOR | LINE |
| TOP VIEW |
| FRONT FLOOR | |
| BRACKET | |||
SYSTEM SEISMIC ANCHORING, FIGURE 1 |
| FIGURE 3 | ||
|
|
|
|
|
NOTES:
Figure 13 Seismic anchor drawing: 800 – 1000 amp Liebert STS2
1. RECOMMENDED | FLOOR | ANCHOR: | 1/2" | ITW | RAMSET/RED | HEAD | |||
SELF DRILLING ANCHOR, | ICBO | OR | EQUIVALENT | (NOT |
| ||||
(SUPPLIED). FOLLOW MANUFACTURER'S INSTRUCTIONS. |
|
|
| ||||||
2. POSITION | REAR | FLOOR | BRACKETS | ON FLOOR | AT LEAST | .75" |
| ||
FROM BACK | WALL. | MARK | LOCATION | A ND DRILL | HOLES (FIG. 1) | TO | |||
A MINIMUM DEPTH OF 4.12" INTO THE CONCRETE.
3.INSTALL REAR CABINET BASE BRACKET (FIG. 2) TO EXISTING HOLES ON UNDERSIDE OF UNIT WITH TABS FACING BACK WALL.
USE SUPPLIED HARDWARE AND TORQUE TO 365
NOTE, LOOSEN LEVELING BOLT LOCKING NUT AND TIGHTEN AFTER BRACKET IS SECURED.
4.INSTALL FRONT CABINET BASE BRACKET (FIG. 3) TO EXISTING
HOLES | ON U NDERSIDE | OF UNIT WITH BENT FLANGE FACING FRONT. |
USE SUPPLIED HARDWARE AND TORQUE TO 365 | ||
NOTE, | LOOSEN LEVELING BOLT LOCKING NUT AND TIGHTEN AFTER | |
BRACKET IS SECURED. |
| |
5. MOVE | CABINET INTO | P OSITION | W ITH REAR TABS INTO S LOTS OF | |
FLOOR BRACKET. TABS TO EXTEND AT LEAST 1/2" THROUGH FLOOR | ||||
BRACKET | (FIG. | 2). THEN | ATTACH | FRONT FLOOR BRACKETS TO FRONT |
CABINET | BASE | BRACKET | BUT DO N OT FULLY T IGHTEN HARDWARE. | |
6. MARK | HOLE LOCATIONS AND REMOVE BRACKETS. DRILL AND INSTALL | |||
FLOOR | BRACKETS. | UNIT | DOOR CAN BE REMOVED |
| FOR BETTER | ACCESS. | |||||||
REINSTALL | FRONT | FLOOR | BRACKETS | TO FRONT | CABINET | BRACKETS | WITH | ||||||
SUPPLIED HARDWARE AND TORQUE TO 235 |
|
|
| ||||||||||
7. IF SIDE | WALLS | ARE | PRESENT, | 5.0 INCH MINIMUM | D ISTANCE | FROM | EITHER | ||||||
SIDE WALL | IS REQUIRED. |
|
|
|
|
|
|
|
|
| |||
8. REAR | A ND FRONT | FLOOR | BRACKETS, | AND REAR | AND | FRONT | CABINE T | ||||||
BASE BRACKETS | ARE | 1010 | STEEL | AND | APPROX. | .25 INCH | THICK. |
| |||||
PS211805
Rev. 0
Installation Drawings
