Attaching the Wire Reel Stands

C-3

ACCESSORIES

Return to Section TOC

Return to Master TOC

The mounting hardware for mounting the stands is included with the LN-9 GMA. Screws and washers are inserted in their respective mounting holes. To con- nect:

1.Remove the three 3/8 in. hex head bolts from the back of the wire feed unit.

2.Place the wire reel mounting stand mounting bracket in position against the back of the wire feed unit.

3.Replace and tighten the hex head bolts. The long screw and plain washer go into the top hole.

WIRE REEL DOOR KIT

Mounts to K303 or to K445 equipped with an S14543 dust shield housing kit, to completely enclose wire reels against extremely dusty and dirty environments. Includes a hinged door and sliding bottom seal. Install the door according to instructions included with the kit.

SPINDLE FOR READI-REELS AND 2" I.D. SPOOLS (K162-H*)

(60 Lb. Maximum Capacity)

The 2" O.D. spindle kit is for use with the K303. The shaft for the standard 50-60 pound wire coils is removed from the mounting framework, and the K162H is installed in its place. Includes an easily adjustable friction brake for control of overrun.

When used with Readi-Reels, a Readi-Reel Adapter is required.

When used with 8" O.D. spools, a K468 Spindle Adapter is available.

14 Lb. lnnershield coils can be mounted to the spindle using the K435 Adapter.

* Replaces the K162 30 Lb. Spindle Kit.

Install the spindle according to instructions included with the kit:

K162 - 30lb (13.6 kg) – M14573 Mounting instructions K162H - 60 lb (27.2 kg) – M15241 Mounting instructions

CAUTION

DO NOT USE COILS OR SPOOLS HEAVIER THAN 30 LBS. ON THE ORIGINAL K162 SPINDLE.

READI-REEL ADAPTERS

K363-PAdapts Lincoln Readi-Reel coils of electrode (30 lb. and 22 lb.) to a 2" spindle. One-piece construc- tion. Made from a durable molded plastic. Designed for easy loading; adapter remains on spindle for quick changeover. Included with K377 small mounting stand.

K438 Adapts 50-60 lb. Lincoln Readi-Reel coils to a K162-H spindle, or similar 2 inch spindle suitable for 60 lb. spools. Two-piece construction made from a durable flame retardant molded plastic. Designed for minimum loading downtime, the coils easily load with inside adapter half on spindle. Four twist latches lock adapter halves together. Included with K445 50-60 lb. Readi-Reel stand.

60 LB. (27.2 KG) COIL ADAPTER (K1504-1)

Permits 50-60 lb. (22.7-27.2 Kg) coils to be mounted to a 2" (51mm) spindle.

SMALL MOUNTING STAND FOR READI-REEL COILS OR 2" I.D. SPOOLS (K377)

(30 Lb. Maximum Capacity)

This assembly includes a small frame to which is attached a wire reel spindle similar to the K162 spindle. The unit is supplied with the K363 Readi-Reel Adapter for use with the Lincoln 22-30 lb. Readi-Reel Electrode Coils. Without the adapter the unit is capable of han- dling up to 30 lb. spools with a 2 " I.D., a 12" max. O.D., and a 4 " width. For spools with an 8" O.D., a K468 Spindle Adapter is available.

14 lb. lnnershield coils can be mounted to the spindle using the K435 Adapter. The spindle has an easily adjustable braking system.

SMALL MOUNTING STAND FOR 13-14 LB. INNER- SHIELD COILS (K378)

This assembly includes the same smaller frame as used in the K377 and a fully enclosed canister system for de-reeling of the 14 pound coil. This system has a fixed brake for the 14 pound coil.

50-60 LB. WIRE REEL ASSEMBLY FOR CUSTOMER MOUNTING (K299)

This assembly is available only when ordering either the LN-9F GMA 2-Roll or 4-Roll model. It includes a 50-60 lb. wire reel, spindle shaft, adjustable brake, insulation and mounting hardware.

Install the assembly according to instructions included with it.

Lincoln Electric SVM138-A Attaching the Wire Reel Stands, Wire Reel Door KIT, READI-REEL Adapters

Models: SVM138-A

ACCESSORIES