Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
| OPERATION |
| ||||
|
| GTAW (TIG) WELDING |
|
|
|
|
|
| The POWER FEED® / Power Wave system is excellent | ||||
|
| for Touch Start TIG welding. |
|
|
|
|
|
| The system supports TIG torches with or without gas | ||||
|
| control valves. TIG torches with gas control valves con- | ||||
|
| nect directly to the gas flow regulator. For TIG torches | ||||
|
| without gas control valves, connect the output gas | ||||
|
| hose on the wire feeder to the TIG torch gas hose. | ||||
|
| The wire feeder gas solenoid may be enabled or dis- | ||||
|
| abled by parameter P.8 in the | ||||
|
| operations section. |
|
|
|
|
|
|
|
|
|
|
|
Touch Start | TIG | No Foot / Hand Amptrol |
| With Foot / Hand Amptrol | ||
Weld Sequence |
|
|
|
|
| |
|
| 1. Adjust the arc amperage with the left knob | 1. Adjust the maximum arc amperage with |
| ||
|
| on the display panel. |
| the left knob on the display panel. | ||
|
| 2. Turn the right knob on the display panel | 2. Touch the tungsten to the work piece. | |||
|
| until the Output Control is ON. Gas will | 3. | Press the foot pedal or slide the hand | ||
|
| start to flow. |
| amptrol a slight amount. Gas will start to | ||
TIG torches without | 3. Touch the tungsten to the work piece. |
| flow. | |||
4. Lift the tungsten to create an arc and weld. | 4. | Lift the tungsten to create an arc. | ||||
|
| 5. Stop welding by turning the Output Control | 5. | Regulate the arc current with the foot | ||
|
| to OFF, or by pulling away the tungsten |
| pedal or hand amptrol. | ||
|
| from the work. | 6. | Stop welding by releasing the foot pedal or | ||
|
| 6. Gas flow will continue for a short time and |
| hand amptrol, or by pulling the tungsten | ||
|
| then |
| away from the work. | ||
|
|
| 7. | Gas will continue for a short time and then | ||
|
|
|
| |||
|
|
|
|
| ||
|
| 1. Adjust the arc amperage with the left knob | 1. Adjust the maximum arc amperage with | |||
|
| on the display panel. |
| the left knob on the display panel. | ||
|
| 2. Turn the right knob on the display panel | 2. Touch the tungsten to the work piece. | |||
|
| until the Output Control is ON. | 3. | Press the foot pedal or slide the hand | ||
TIG torches | with | 3. Open the gas valve on the TIG torch. |
| amptrol a slight amount. | ||
4. Touch the tungsten to the work piece. | 4. Open the gas valve on the TIG torch. | |||||
|
| 5. Lift the tungsten to create an arc and weld. | 5. | Lift the tungsten to create an arc. | ||
|
| 6. Stop welding by turning the Output Control | 6. | Regulate the arc current with the foot | ||
|
| to OFF, or by pulling away the tungsten |
| pedal or hand amptrol. | ||
|
| from the work. | 7. | Stop welding by releasing the foot pedal or | ||
|
| 7. Close the gas valve on the TIG torch. |
| hand amptrol, or by pulling the tungsten | ||
|
|
|
| away from the work. | ||
|
|
| 8. | Close the gas valve on the TIG torch. | ||
|
|
|
|
|
|
|
