Return to Section TOC
Return to Master TOC
OPERATION | ||
| Steel and Stainless |
|
220 | 1.06 |
WFS AMPS | VOLTS TRIM |
Less | More | Shorter | Longer |
Deposition | Deposition | Arc | Arc |
MSP4 OPERATION
Return to Section TOC
Section TOC
Return to Master TOC
Master TOC
WELD MODE
ELECTRODE AND GAS |
| WIRE SIZE |
| |||
0.030 | 0.035 | 0.045 | 0.052 | |||
|
| |||||
Steel(Crisp) | Ar(Mix) | 95 | 12 | 22 | 201 | |
Steel(Soft) | Ar(Mix) | 14 | 19 | 28 | ||
Stainless | Ar/ CO2 | 66 | 36 | 46 | ||
Stainless | Ar/ CO2 | 62 | 32 | 42 | ||
Stainless | Ar/He/CO2 | 34 | 44 | |||
| WAVEFORM CONTROL TECHNOLOGY | ||
| 12 | STEEL | |
IR PORT | .035" | ||
SETUP | |||
|
| ||
| Pulse Crisp ArMix | ||
WELD MODE |
| START OPTIONS | |
ARC CONTROL |
| END OPTIONS | |
SET
START OPTIONS | ||
PREFLOW TIME |
| DESCRIPTION |
|
|
|
0 - 10 seconds |
| Adjusts the time that shielding |
|
| gas flows after the trigger is |
|
| pulled and prior to feeding wire. |
|
|
|
Off, 50 to150 in/min. |
| |
|
| speed from the time the trigger |
|
| is pulled until an arc is estab- |
|
| lished. |
Start Procedure |
| The Start Procedure controls |
|
| the WFS, Trim a t a specified |
|
| time at t he beg inni ng of the |
|
| weld. During the start time, the |
|
| machine will ramp up or down |
|
| from the Start Procedure to the |
|
| preset Welding Procedure. |
|
| |
|
|
|
Return to
Return to Section TOC
Return to
Return to Master TOC
| ARC CONTROL | ||
ARC |
|
| DESCRIPTION |
FOCUS |
|
|
|
|
| Arc Focus adjusts the arc from | |
10.0 (STIFF) |
|
| a wide, soft arc good for out of |
|
|
| position work to a narrow, stiff |
|
|
| arc preferred for faster trav el |
|
|
| speeds. The pulse frequency is |
|
|
| lower with a soft arc and higher |
|
|
| with a stiff arc. |
|
|
|
|
|
|
|
|
| END OPTIONS | ||||
EFFECT / RANGE |
|
|
| FUNCTION |
|
|
|
|
|
|
|
Postflow Time: |
|
|
| Adjusts the time that shielding |
|
0 to 10 seconds |
|
|
| gas flows after the welding out- |
|
|
|
|
| put turns off. |
|
Burnback: 0 to .25 |
|
|
| Th e burnba ck tim e is the |
|
|
|
|
| ||
Seconds |
|
|
| amount of time that the weld |
|
|
|
|
| output continues after the wire |
|
|
|
|
| stops feeding. It prevents the |
|
|
|
|
| wire from sticking in the puddle |
|
|
|
|
| and prepares the end of the |
|
|
|
|
| wire for the next arc start. |
|
Crater Procedure |
|
|
| Crater P rocedure controls the |
|
|
|
|
| WFS and Trim for a specified |
|
|
|
|
| time at the end of the weld |
|
|
|
|
| after the trigger is released. |
|
|
|
|
| Dur ing the Crat er tim e, t he |
|
|
|
|
| machine will ramp up or down |
|
|
|
|
| from the Weld Proced ure to |
|
|
|
|
| the Crater Procedure. |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
