B-29

 

OPERATION

B-29

TOC

TOC

PROCEDURE/MEMORY PANEL OPERA-

USER MEMORIES

 

TION

 

 

Recall a memory with memory buttons

 

 

 

 

 

 

Section

Master

 

 

 

 

The Dual Procedure/Memory Panel performs three

To recall a user a memory, press one of the six user

 

 

 

 

functions:

 

 

to

to

 

 

 

memory buttons. The memory is recalled when the but-

• Weld procedure selection

 

 

ton is released. Do not hold the button for more than

Return

Return

 

 

• Memory save and recall

 

 

two seconds when recalling a user memory.

 

 

 

 

 

 

 

 

• Limits setting

 

 

Recall a memory with the gun trigger

 

 

 

 

 

 

 

 

 

There are two procedure memories (A and B) and six

If desired, memories 2 through 6 can be recalled with

 

 

user memories (1-6).

 

 

 

 

 

 

 

the gun trigger. For example, to recall memory 3, quick-

 

 

Procedure Memory vs. User Memory

 

ly pull and release the gun trigger 3 times without weld-

 

 

 

 

 

ing.

 

 

 

Procedure memory is used while welding. Changes to

Note: the POWER FEED® Wire Feeders are factory

 

 

the weld procedure (WFS, voltage, arc control, etc.)

TOC

TOC

immediately change the contents inside the selected

set with this feature disabled. Use the SETUP menu

procedure memory.

 

 

and change P.4 to enable memory recall with the gun

 

 

 

 

Section

Master

 

 

 

trigger.

 

User memories work by copying the weld procedure

Save a memory with memory buttons

 

to

to

from one of the six memories into either the A or B pro-

pressed, the corresponding LED will illuminate. After

Return

Return

cedure. Weld procedures are saved into the memories

 

 

To save a memory, press and hold the desired memo-

 

 

only when the operator chooses.

 

ry button for two seconds. When the button is initially

 

 

 

USER

 

two seconds, the LED will turn off. Do not hold the but-

 

 

PROCEDURE

MEMORIES

 

ton for more than 5 seconds when saving a user mem-

 

 

 

 

 

 

MEMORY

 

 

ory.

 

 

 

 

 

 

 

 

 

 

 

 

M

MEMORY

 

M

Note that memories may be locked using Weld

 

 

PROCEDURE

 

 

 

 

 

 

 

 

 

 

Manager from a P.C. or Palm application to prevent

 

 

A

GUN

B

1

2

3

 

 

 

 

 

 

 

accidental overwrite of the memories. If an attempt is

 

 

 

 

 

 

 

 

 

TOC

TOC

 

 

 

 

HOLD 2 SECONDS TO SAVE

 

 

made to save

a

memory when

memory saving is

 

 

 

4

5

6

 

locked, the message "Memory save is Disabled!" will

 

 

 

 

 

 

Section

Master

 

 

 

 

appear briefly in the MSP4 display.

 

 

 

 

 

 

 

 

RECALL

 

SAVE

 

to

to

 

 

 

 

 

 

 

PRESS 1

 

PRESS 2

 

 

 

 

 

 

 

 

SECOND

SECONDS

 

Return

Return

Using Procedure Memories

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M

MEMORY

M

Procedure memories can be selected by choosing

PROCEDURE

 

 

 

either "A" or "B" procedure directly with the memory

A GUN B

1

2

3

 

panel, or by selecting "GUN" and using a dual proce-

 

 

 

 

dure gun to select between procedure "A" and "B".

 

 

HOLD 2 SECONDS TO SAVE

 

 

 

 

 

When selecting procedures with the gun switch, "A" or

 

4

5

6

"B" will flash to show which procedure is active.

 

 

 

 

 

 

 

 

M

MEMORY

M

 

 

PROCEDURE

 

 

 

TOC

TOC

A GUN B

1

2

3

 

 

 

 

 

to Section

to Master

 

 

HOLD 2 SECONDS TO SAVE

 

 

4

5

6

PRESS TO

 

 

 

Return

Return

SELECT

 

 

 

PROCEDURE OR

 

 

 

QUICK TRIGGER-

 

 

 

WHILE

 

 

POWER FEED® 25M

 

 

WELDING

 

 

Page 47
Image 47
Lincoln Electric SVM185-A service manual PROCEDURE/MEMORY Panel Opera User Memories Tion