Screen, Rudder Threshold set up | Lowrance electronic LMF-200

1.Press MENU, use the UP and DOWN keys to select PAGES and press MENU. Select SET POP-UPand press MENU.

2.The Set Pop-up menu will appear with three options: Pages, Threshold and Stay Time. Select THRESHOLD and press MENU.

3.Select TRIM TABS from the Threshold menu and press MENU.

4.Use the UP and DOWN keys to choose a threshold between 3 and 50 percent. Press MENU. You will be taken back to the main display.

Rudder Threshold set up:

Make sure Rudder has been selected on the Pop-up Pages menu before setting a threshold. If Rudder is not selected on the Pop-up Page menu, a Rudder pop-up will not appear, regardless of the threshold.

1.Press MENU, use the UP and DOWN keys to select PAGES and press MENU. Highlight SET POP-UPand press MENU.

2.The Set Pop-up menu will appear with three options: Pages, Threshold and Stay Time. Select THRESHOLD and press MENU.

3.Select RUDDER from the Threshold menu and press MENU.

4.Use the UP and DOWN keys to choose a threshold between 3 and 40 degrees. Press MENU and you will be taken back to the main display.

Screen

The Screen menu allows you to adjust the appearance of the screen. There are three options in the screen menu: Backlight, Contrast and Reverse Video.

Backlight

The Backlight feature allows you to brighten or dim the light in the LMF-200.

To adjust Backlight:

1.Press MENU, use the UP and DOWN keys to select SCREEN and press MENU. The Screen menu will appear with three options: Backlight, Contrast and Rev Video.

2.Select BACKLIGHT and press MENU, which will open the Backlight menu with two options: BL Sync and Adjust.

3.To adjust the backlight, select ADJUST and press MENU. A flashlight graphic will appear.

4.Use the UP and DOWN keys to set the backlight to a desired level.

5.Press MENU to accept the new setting and return to the main display.

Backlight Sync (BL Sync)

By turning on the Backlight Sync function, all the backlight levels for components on the LowranceNet may be controlled by any of the gauges or display units in the network. If you adjust the backlight on

18

Image 24

Lowrance electronic LMF-200 manual Screen, Rudder Threshold set up, To adjust Backlight, Backlight Sync BL Sync

Contents

LMF-200 Copyright 2006 Lowrance Electronics, Inc All rights reserved Visit our web site Table of Contents Backlight Sync BL Sync Iii Page Introduction Page Preparation Recommended Tools and Supplies Installation Sequence Mounting the Gauge Wiring LMF-200 cable connections Connecting to a Nmea 2000 Network CompatibilityNetwork Backbone and Network Nodes Adding a Network Node Additional Network Information Menu Commands Understanding this ManualUp and Down keys Menu key Boat Setup To execute Boat Setup Timeout Basic MenuPages Viewing Pages Page Screen Rotation Options Pages Menu To add a page to the display RemoveTo remove a page from the display Autoscroll Pop-ups Setup To set a Pop-UpStay Time To set Stay Time RPM Threshold set up Engine Trim Threshold set upTrim Tabs Threshold set up Pop-up Thresholds Rudder Threshold set up To adjust BacklightScreen Backlight Audio Setup To adjust ContrastContrast Reverse Video Rev Video System Setup Menu Sonar Alarms To set the Shallow AlarmTo set the Deep Alarm Timeout To reset Eng/Tank configurationReset To reset values To access the Nmea Information screen To access System Information screenNmea Info System Information To set Engine Warnings Speed RangeTo set Speed Range Pressure Range To set Pressure Range UnitsTo change Speed and Distance units To change Temperature units To change Pressure unitsTo change Depth units To change GPS units Fuel Setup To change Volume unitsRefill Tank Refill T To refill tank To use Partial Fill Economy Speed Eco spdTo change Economy Speed Source Fuel Remaining Source FRem Src Customizing Pages To customize the Single Digital To customize the Dual Digital To Customize the Gauge To Customize the Fuel Manager To Customize Trim Tabs EP-35 Temperature Configuration To configure EP-35 Temp Sensor To unconfigure EP-35 temp sensor To reconfigure an EP-35 temp sensorIf all temps configured Configuration name unavailable EP-10 Fuel Flow Configuration If desired configuration name available To configure Fuel Flow To unconfigure an EP-10 Fuel Flow To reconfigure an EP-10 Fuel Flow If all fuel flows configured Configuration name unavailable If configuration name available EP-15 Fluid Level Configuration Fluid Level menu To configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To unconfigure EP-15 Fluid Level To reconfigure EP-15 Fluid Level To execute Reset command Level WarningTo set a Level Warning Suzuki Engine Interface Configuration To configure Suzuki Engine Interface To unconfigure a Suzuki Engine Interface To reconfigure a Suzuki Engine Interface If all interfaces configured Configuration name unavailable Fuel Warning Calibrating EP Sensors EP-10 Fuel Flow CalibrationFuel Flow Accuracy Refill Tank To calibrate an EP-10 Fuel Flow Reset Calibration To execute Reset Calibration commandPartial Fill EP-15 Fluid Level Calibration To execute 2-Point calibration Point Calibration To execute 3-Point calibration To execute 5-Point calibration To Reset Calibration Calibrating Fuel Flow in a Suzuki Engine InterfaceEngine Interface Accuracy To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-free Accessory Ordering Information for all countries Visit our web site