Merlin Magix | Lucent Technologies Network Access Module instruction

MERLIN

MAGIX™

Integrated Network

Access (INA) Module

Installation and

Configuration Guide

Lucent Technologies

October 1999

7820-1000-001

Image 1

Lucent Technologies Network Access Module manual Merlin Magix

Contents

Merlin Magix Year 2000 Compliance Your Responsibility for Your System’s Security Copyright and Trademarks Page Contents Using the INAWizard ContentsUsing the Command Line Interface Troubleshooting Using PMVisionCable Specifications Merlin Magix Administration Viii Index Important Safety Instructions -SAVE These Instructions Safety Instructions Important Safety Instructions -SAVE These Instructions Audience About This GuideRelated Documentation Merlin Magix Documentation SPM, Maintenance and Troubleshooting Calling Group Supervisor and Service Observer User GuideRelated Documentation Merlin Legend Superscript Communications System, Release Additional References PortMaster Documentation Document Advisories Document ConventionsDocument Conventions Convention Use Examples Bold font Technical Support Limited WarrantyINA Module Training Courses USA Dealers and Value-Added Resellers VARS. Call Subscribing to PortMaster Mailing Lists Xvi INA Module INA AdministrationINA Module Description On the Merlin Magix INA Front Panel On the INA ModuleINA Front Panel INA Module 1INA Module Front Panel Installation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line Set Up T1/PRI on the Merlin Magix Getting Ready for ConfigurationSetting Example T1/PRI Provisioning Network Settings Network SettingsAssign T1/PRI Channels Settings Example 192.198.32.17 16172.26.131.37Hours 192.198.32.33 Install the INA Module in a Carrier Installing the INA ModuleConnect Cables Connect a Serial Passthrough Cable Set DIP switch 1 to the right Set DIP SwitchesSet DIP switch 2 to the left Connect Cables Connect a Console Optional Installing the INA ModuleConnect a T1/PRI Cable Observe LED Behavior Connect an Ethernet CableT1/PRI LEDs Observe LED Behavior System LED System LED 8Ethernet LEDs Ethernet LEDs Install the Wizard Using the INAWizardConnect the Workstation to the INA Module Over a LAN Run the Wizard Using the C0 Console Port Using the Command Line InterfaceConnect a Console Using the Passthrough Serial Connection Using a Telnet SessionSet the Administrative Password Log Command set ether0 broadcast highlow Command set password PasswordSet the Ether0 Network Address Set the IP Address and Netmask Command set sysname String Set the Default Route GatewaySet the System Name Set the System Name Set the Name Service Configure the WAN PortSet the Name Server Set the Domain Name Set the Channel Rate Set Up Additional WAN PortsSet the Port IP Address Optional Set the Netmask Set the Destination IP AddressSet the Transport Protocol Apply Filters to the WAN Port Optional Configure the WAN Port Install PMVision Using PMVision Run PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Working with Configuration Panels Using Configuration FunctionsSelecting PMVision Functions Selecting PMVision Functions Working with Configuration Displays Enter Basic SettingsSave Edit Default gateway INA→ Configure→ Global Edit System name INA→ Configure→ SnmpName service type INA→ Configure→ Global Name server address INA→ Configure→ Global Back Up the INA Module Settings Using the Backup and Restore Functions 6PMVision Backup Dialog Restore the INA Module Settings LED Behavior Possible Cause Solution Troubleshooting aObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Observe the boot messages displayed on the console screen Press the reboot button Field Possible Message Explanation Error at failedMemory address Address Table A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test Jacks Test Jack Label Description and Usage Using the DS-1 Test Jacks Figure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Signal Cable SpecificationsCables Specified Console Cable T1/PRI Cable Ethernet Connector Transmission Type Cable Type DistanceEthernet Interface T1/PRI Cable Crossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INA Module Administration Options Merlin Magix AdministrationINAModule System Programming Summary Activate or Deactivate the Onboard CSU INA Module Administration OptionsDSU Channel Selection Error Events INA Module Maintenance OptionsINA Module Maintenance Options Selection Description Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events INA ModuleMaintenance OptionsHour Event Totals Description Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current Events Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkDemand Tests Line Loopback Test INA Module System Interactions Backup and RestoreSurrogate Operation Board Renumbering Pcmcia Flash Memory Card-Based Upgrade OperationPrint Reports Other System Interactions Condition Explanation System Erase ReplacementFrigid Start System Restart INA Module System Interactions Index-1 Index Index-2 Index Index-3 Index-4 T1/PRI Index-5