Lucent Technologies Network Access Module instruction

Using the DS-1 Test Jacks

A-8	INA Module Installation and Configuration Guide

Image 56

Lucent Technologies Network Access Module manual Using the DS-1 Test Jacks

Contents

Merlin Magix Your Responsibility for Your System’s Security Year 2000 Compliance Copyright and Trademarks Page Contents Using the Command Line Interface ContentsUsing the INAWizard Using PMVision TroubleshootingCable Specifications Merlin Magix Administration Index Viii Safety Instructions Important Safety Instructions -SAVE These Instructions Important Safety Instructions -SAVE These Instructions About This Guide AudienceRelated Documentation Merlin Magix Documentation Calling Group Supervisor and Service Observer User Guide SPM, Maintenance and TroubleshootingRelated Documentation Merlin Legend Superscript Communications System, Release PortMaster Documentation Additional References Document Conventions Document AdvisoriesDocument Conventions Convention Use Examples Bold font Limited Warranty Technical SupportINA Module Training Courses USA Dealers and Value-Added Resellers VARS. Call Subscribing to PortMaster Mailing Lists Xvi INA Administration INA ModuleINA Module Description On the Merlin Magix INA Front Panel On the INA ModuleINA Front Panel 1INA Module Front Panel INA Module Collect information about your T1 or PRI line Installation and Configuration StepsInstallation and Configuration Steps Getting Ready for Configuration Set Up T1/PRI on the Merlin MagixSetting Example T1/PRI Provisioning Assign T1/PRI Channels Network SettingsNetwork Settings Settings Example 16172.26.131.37 192.198.32.17Hours 192.198.32.33 Installing the INA Module Install the INA Module in a CarrierConnect Cables Connect a Serial Passthrough Cable Set DIP Switches Set DIP switch 1 to the rightSet DIP switch 2 to the left Connect Cables Connect a T1/PRI Cable Installing the INA ModuleConnect a Console Optional Connect an Ethernet Cable Observe LED BehaviorT1/PRI LEDs Observe LED Behavior System LED System LED Ethernet LEDs 8Ethernet LEDs Using the INAWizard Install the WizardConnect the Workstation to the INA Module Over a LAN Run the Wizard Connect a Console Using the Command Line InterfaceUsing the C0 Console Port Using a Telnet Session Using the Passthrough Serial ConnectionSet the Administrative Password Log Command set password Password Command set ether0 broadcast highlowSet the Ether0 Network Address Set the IP Address and Netmask Set the Default Route Gateway Command set sysname StringSet the System Name Set the System Name Configure the WAN Port Set the Name ServiceSet the Name Server Set the Domain Name Set the Port IP Address Optional Set Up Additional WAN PortsSet the Channel Rate Set the Destination IP Address Set the NetmaskSet the Transport Protocol Apply Filters to the WAN Port Optional Configure the WAN Port Using PMVision Install PMVision Run PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Using Configuration Functions Working with Configuration PanelsSelecting PMVision Functions Selecting PMVision Functions Enter Basic Settings Working with Configuration DisplaysSave Edit Edit System name INA→ Configure→ Snmp Default gateway INA→ Configure→ GlobalName service type INA→ Configure→ Global Name server address INA→ Configure→ Global Using the Backup and Restore Functions Back Up the INA Module Settings Restore the INA Module Settings 6PMVision Backup Dialog Observing LED Behavior Troubleshooting aLED Behavior Possible Cause Solution Attach a console Observing Boot MessagesObserving Boot Messages Press the reboot button Observe the boot messages displayed on the console screen Error at failed Field Possible Message ExplanationMemory address Address Using the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test Jacks Test Jack Label Description and Usage Figure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cable Specifications SignalCables Specified Console Cable Ethernet Connector Transmission Type Cable Type Distance T1/PRI CableEthernet Interface T1/PRI Cable Crossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INAModule System Programming Summary Merlin Magix AdministrationINA Module Administration Options DSU Channel Selection INA Module Administration OptionsActivate or Deactivate the Onboard CSU INA Module Maintenance Options Error EventsINA Module Maintenance Options Selection Description INA ModuleMaintenance Options Menu Maintenance→ Slot→ Slot#→ Enter→ Error EventsHour Event Totals Description Clearing Error Events Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ CurrentMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current Events Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbk Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→Demand Tests Line Loopback Test Surrogate Operation Backup and RestoreINA Module System Interactions Pcmcia Flash Memory Card-Based Upgrade Operation Board RenumberingPrint Reports Other System Interactions Replacement Condition Explanation System EraseFrigid Start System Restart INA Module System Interactions Index Index-1 Index Index-2 Index-3 T1/PRI Index-4 Index-5