Lucent Technologies Network Access Module specs

Copyright and Trademarks

MLX-10, MLX-20L, MLX-28D, MLS-6, MLS-12, MLS-12D, MLS-18D, MLS-34D, PortMaster, ComOS, and MERLIN are registered trademarks and PMVision and MERLIN MAGIX are trademarks of Lucent Technologies. All other marks are the product of their respective owners.

Page 3

Image 3

Lucent Technologies Network Access Module manual Copyright and Trademarks

Contents

Merlin Magix Year 2000 Compliance Your Responsibility for Your System’s Security Copyright and Trademarks Page Contents Contents Using the INAWizardUsing the Command Line Interface Merlin Magix Administration Using PMVisionTroubleshooting Cable Specifications Viii Index Important Safety Instructions -SAVE These Instructions Safety Instructions Important Safety Instructions -SAVE These Instructions Merlin Magix Documentation About This GuideAudience Related Documentation Merlin Legend Superscript Communications System, Release Calling Group Supervisor and Service Observer User GuideSPM, Maintenance and Troubleshooting Related Documentation Additional References PortMaster Documentation Convention Use Examples Bold font Document ConventionsDocument Advisories Document Conventions USA Dealers and Value-Added Resellers VARS. Call Limited WarrantyTechnical Support INA Module Training Courses Subscribing to PortMaster Mailing Lists Xvi On the Merlin Magix INA AdministrationINA Module INA Module Description On the INA Module INA Front PanelINA Front Panel INA Module 1INA Module Front Panel Installation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line T1/PRI Provisioning Getting Ready for ConfigurationSet Up T1/PRI on the Merlin Magix Setting Example Network Settings Network SettingsAssign T1/PRI Channels Settings Example 192.198.32.33 16172.26.131.37192.198.32.17 Hours Connect a Serial Passthrough Cable Installing the INA ModuleInstall the INA Module in a Carrier Connect Cables Connect Cables Set DIP SwitchesSet DIP switch 1 to the right Set DIP switch 2 to the left Installing the INA Module Connect a Console OptionalConnect a T1/PRI Cable Observe LED Behavior Connect an Ethernet CableObserve LED Behavior T1/PRI LEDs System LED System LED 8Ethernet LEDs Ethernet LEDs Over a LAN Using the INAWizardInstall the Wizard Connect the Workstation to the INA Module Run the Wizard Using the Command Line Interface Using the C0 Console PortConnect a Console Log Using a Telnet SessionUsing the Passthrough Serial Connection Set the Administrative Password Set the IP Address and Netmask Command set password PasswordCommand set ether0 broadcast highlow Set the Ether0 Network Address Set the System Name Set the Default Route GatewayCommand set sysname String Set the System Name Set the Domain Name Configure the WAN PortSet the Name Service Set the Name Server Set Up Additional WAN Ports Set the Channel RateSet the Port IP Address Optional Apply Filters to the WAN Port Optional Set the Destination IP AddressSet the Netmask Set the Transport Protocol Configure the WAN Port Install PMVision Using PMVision Using a Crossover Cable Run PMVisionRun PMVision Using PMVision Communicate with the INA ModuleCommunicate with the INA Module Selecting PMVision Functions Using Configuration FunctionsWorking with Configuration Panels Selecting PMVision Functions Edit Enter Basic SettingsWorking with Configuration Displays Save Name server address INA→ Configure→ Global Edit System name INA→ Configure→ SnmpDefault gateway INA→ Configure→ Global Name service type INA→ Configure→ Global Back Up the INA Module Settings Using the Backup and Restore Functions 6PMVision Backup Dialog Restore the INA Module Settings Troubleshooting a LED Behavior Possible Cause SolutionObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Observe the boot messages displayed on the console screen Press the reboot button Address Error at failedField Possible Message Explanation Memory address Table A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test Jacks Test Jack Label Description and Usage Using the DS-1 Test Jacks Figure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Console Cable Cable SpecificationsSignal Cables Specified T1/PRI Cable Ethernet Connector Transmission Type Cable Type DistanceT1/PRI Cable Ethernet Interface RJ-45 Connector Crossover CableCrossover Cable Crossover Cable Merlin Magix Administration INA Module Administration OptionsINAModule System Programming Summary INA Module Administration Options Activate or Deactivate the Onboard CSUDSU Channel Selection Selection Description INA Module Maintenance OptionsError Events INA Module Maintenance Options Description INA ModuleMaintenance OptionsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events Hour Event Totals Current Events Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Line Loopback Test Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Demand Tests Backup and Restore INA Module System InteractionsSurrogate Operation Other System Interactions Pcmcia Flash Memory Card-Based Upgrade OperationBoard Renumbering Print Reports System Restart ReplacementCondition Explanation System Erase Frigid Start INA Module System Interactions Index-1 Index Index-2 Index Index-3 Index-4 T1/PRI Index-5