T1/PRI Cable

Table B-2shows the pinouts for a category 5 unshielded, ungrounded, twisted pair cable, as specified by the EIA/TIA-568-B wiring standard, with an RJ-48C connection

Table B-2T1/E1 RJ-48C Connector Pinout

T1 Port

			Direction to or
			from the INA
RJ-48C	Signal	Definition	Module

1	RXD (Ring)	Receive Data	Input
2	RXD (Tip)
4	TXD (Ring)	Transmit Data	Output
5	TXD (Tip)

Ethernet Interface

Table B-3provides specifications for the 10Mbps baseband IEEE 802.3-compatible Ethernet interface.

Table B-3Ethernet Interface

Ethernet	Connector		Transmission
Type	Type	Cable Type	Distance

RJ-48C	RJ-48C for 10BaseT	Category 5	Hub distance—328ft (100m) maximum
		unshielded	Repeaters—four maximum
		twisted pair

B-2	INA Module Installation and Configuration Guide

Page 58

Image 58

Lucent Technologies Network Access Module manual T1/PRI Cable, Ethernet Interface

Contents

Merlin Magix Your Responsibility for Your System’s Security Year 2000 Compliance Copyright and Trademarks Page Contents Using the INAWizard ContentsUsing the Command Line Interface Cable Specifications Using PMVisionTroubleshooting Merlin Magix Administration Index Viii Safety Instructions Important Safety Instructions -SAVE These Instructions Important Safety Instructions -SAVE These Instructions Related Documentation About This GuideAudience Merlin Magix Documentation Related Documentation Calling Group Supervisor and Service Observer User GuideSPM, Maintenance and Troubleshooting Merlin Legend Superscript Communications System, Release PortMaster Documentation Additional References Document Conventions Document ConventionsDocument Advisories Convention Use Examples Bold font INA Module Training Courses Limited WarrantyTechnical Support USA Dealers and Value-Added Resellers VARS. Call Subscribing to PortMaster Mailing Lists Xvi INA Module Description INA AdministrationINA Module On the Merlin Magix INA Front Panel On the INA ModuleINA Front Panel 1INA Module Front Panel INA Module Installation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line Setting Example Getting Ready for ConfigurationSet Up T1/PRI on the Merlin Magix T1/PRI Provisioning Network Settings Network SettingsAssign T1/PRI Channels Settings Example Hours 16172.26.131.37192.198.32.17 192.198.32.33 Connect Cables Installing the INA ModuleInstall the INA Module in a Carrier Connect a Serial Passthrough Cable Set DIP switch 2 to the left Set DIP SwitchesSet DIP switch 1 to the right Connect Cables Connect a Console Optional Installing the INA ModuleConnect a T1/PRI Cable T1/PRI LEDs Connect an Ethernet CableObserve LED Behavior Observe LED Behavior System LED System LED Ethernet LEDs 8Ethernet LEDs Connect the Workstation to the INA Module Using the INAWizardInstall the Wizard Over a LAN Run the Wizard Using the C0 Console Port Using the Command Line InterfaceConnect a Console Set the Administrative Password Using a Telnet SessionUsing the Passthrough Serial Connection Log Set the Ether0 Network Address Command set password PasswordCommand set ether0 broadcast highlow Set the IP Address and Netmask Set the System Name Set the Default Route GatewayCommand set sysname String Set the System Name Set the Name Server Configure the WAN PortSet the Name Service Set the Domain Name Set the Channel Rate Set Up Additional WAN PortsSet the Port IP Address Optional Set the Transport Protocol Set the Destination IP AddressSet the Netmask Apply Filters to the WAN Port Optional Configure the WAN Port Using PMVision Install PMVision Run PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Selecting PMVision Functions Using Configuration FunctionsWorking with Configuration Panels Selecting PMVision Functions Save Enter Basic SettingsWorking with Configuration Displays Edit Name service type INA→ Configure→ Global Edit System name INA→ Configure→ SnmpDefault gateway INA→ Configure→ Global Name server address INA→ Configure→ Global Using the Backup and Restore Functions Back Up the INA Module Settings Restore the INA Module Settings 6PMVision Backup Dialog LED Behavior Possible Cause Solution Troubleshooting aObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Press the reboot button Observe the boot messages displayed on the console screen Memory address Error at failedField Possible Message Explanation Address Using the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test Jacks Test Jack Label Description and Usage Figure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cables Specified Cable SpecificationsSignal Console Cable Ethernet Interface Ethernet Connector Transmission Type Cable Type DistanceT1/PRI Cable T1/PRI Cable Crossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INA Module Administration Options Merlin Magix AdministrationINAModule System Programming Summary Activate or Deactivate the Onboard CSU INA Module Administration OptionsDSU Channel Selection INA Module Maintenance Options INA Module Maintenance OptionsError Events Selection Description Hour Event Totals INA ModuleMaintenance OptionsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events Description Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Current Events Demand Tests Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Line Loopback Test INA Module System Interactions Backup and RestoreSurrogate Operation Print Reports Pcmcia Flash Memory Card-Based Upgrade OperationBoard Renumbering Other System Interactions Frigid Start ReplacementCondition Explanation System Erase System Restart INA Module System Interactions Index Index-1 Index Index-2 Index-3 T1/PRI Index-4 Index-5